Home |
Search |
Today's Posts |
![]() |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
![]()
Posted to sci.electronics.repair
|
|||
|
|||
![]()
I am looking for the 6 pin connector [LEMO?] that is used to connect a Tek P6407 probe to the rear of a Tek 2430A digital 'scope. Can anyone suggest a type/series and a source or a NG that is likely to be knowledgable on this??
Thanks. Neil S. |
#2
![]()
Posted to sci.electronics.repair
|
|||
|
|||
![]()
On 3/26/2012 11:55 AM, nesesu wrote:
I am looking for the 6 pin connector [LEMO?] that is used to connect a Tek P6407 probe to the rear of a Tek 2430A digital 'scope. Can anyone suggest a type/series and a source or a NG that is likely to be knowledgable on this?? Thanks. Neil S. Why not call up the TEK service department? If they're in a good mood, they might look up the vendor part number for you. If you have the probe manual, there might be a tek part number in that. Would make the service dept job easier getting the vendor number. There's always lemo.com and mouser is listed as a distributor. google is your friend. |
#3
![]()
Posted to sci.electronics.repair
|
|||
|
|||
![]()
nesesu wrote in
news:[email protected]: I am looking for the 6 pin connector [LEMO?] that is used to connect a Tek P6407 probe to the rear of a Tek 2430A digital 'scope. Can anyone suggest a type/series and a source or a NG that is likely to be knowledgable on this?? Thanks. Neil S. If it's a silver,pull-lock ring type connector with a half-circle inner piece and 3 pin and 3 female receptors,then it's a LEMO connector. a miniature LEMO,IIRC. you probably can download the probe manual on the TEK website,and that should have the manufacturer and their part number along with the TEK part number. Digi Key ought to have them. TEK may list it as a complete cable assembly too. -- Jim Yanik jyanik at localnet dot com |
#4
![]()
Posted to sci.electronics.repair
|
|||
|
|||
![]()
On Monday, March 26, 2012 6:43:21 PM UTC-7, Jim Yanik wrote:
nesesu wrote in news:[email protected]: I am looking for the 6 pin connector [LEMO?] that is used to connect a Tek P6407 probe to the rear of a Tek 2430A digital 'scope. Can anyone suggest a type/series and a source or a NG that is likely to be knowledgable on this?? Thanks. Neil S. If it's a silver,pull-lock ring type connector with a half-circle inner piece and 3 pin and 3 female receptors,then it's a LEMO connector. a miniature LEMO,IIRC. you probably can download the probe manual on the TEK website,and that should have the manufacturer and their part number along with the TEK part number. Digi Key ought to have them. TEK may list it as a complete cable assembly too. -- Jim Yanik jyanik at localnet dot com Looking in the P6407 manual, the connector is part of the the cable assembly, so it is not so easy to find out the series and number of the LEMO part. I have never seen the actual plug that fits the connector but it appears to be a push-pull locking type. Since the likely one is $42+, I want to be absolutely sure before buying one. Lemo has several that look much the same and they do not seem to show any dimensional details of the mating parts, just the outside dimensions so it is difficult to be certain of which one I need, when I can only take measurements of where the plug barrel fits the chassis connecor. Neil S. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Forum | |||
Tektronix TDS210 | Electronics Repair | |||
Agilent vs Tektronix... | Electronics | |||
Tektronix 442 pot 20k | Electronics Repair | |||
Tektronix TDS 540 and options | Electronics Repair | |||
Tektronix T932A | Electronics Repair |