The answering machine portion of this 3 handset DECT phone is unresponsive.
I'd be happy to just turn it "off" but it is stuck "on." A simple reset
from the handset did not work. The base [and handsets] have 2 rows of gold
plated dots [handset battery compartment is 1/2 X 1/4 inch grid, base is
slightly larger but accessible through holes in back] that would appear to
be a service port of sorts. Anyone know if these could be used to fix or
disable the answering machine? Thanks.

On Sat, 1 Oct 2011 10:05:04 -1000, "John Keiser"
wrote:

The answering machine portion of this 3 handset DECT phone is unresponsive.
I'd be happy to just turn it "off" but it is stuck "on." A simple reset
from the handset did not work.

The answering machine message memory might be full. Try emptying the
old messages from memory.

Otherwise, try a grand reset.

You should reset the telephone system. Complete the following steps:
Step 1: Disconnect the power from the telephone base.

Step 2: Disconnect the battery pack from the handset(s).

Step 3: Wait 5 minutes, then reconnect the power to the telephone
base.

Step 4: Connect the battery pack to the handset(s) and install the
battery cover. Wait several seconds for the handset(s) to link with
the base.

Step 5: At the handset, reset the Date and Time.

http://www.vtechphones.com/vtechphones/index.cfm/support/general/frequently-asked-questions-faqs/


--
Jeff Liebermann
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

Jeff,
"0" messages appear.
I had tried the grand reset to no avail. Was hoping for an even grander
reset.
Phones function well enough.
Mostly curious about the service "port" as I my old stand alone answering
machine is working compatibly at the moment.
Thank you.

"Jeff Liebermann" wrote in message
...
On Sat, 1 Oct 2011 10:05:04 -1000, "John Keiser"
wrote:

The answering machine portion of this 3 handset DECT phone is
unresponsive.
I'd be happy to just turn it "off" but it is stuck "on." A simple reset
from the handset did not work.

The answering machine message memory might be full. Try emptying the
old messages from memory.

Otherwise, try a grand reset.

You should reset the telephone system. Complete the following steps:
Step 1: Disconnect the power from the telephone base.

Step 2: Disconnect the battery pack from the handset(s).

Step 3: Wait 5 minutes, then reconnect the power to the telephone
base.

Step 4: Connect the battery pack to the handset(s) and install the
battery cover. Wait several seconds for the handset(s) to link with
the base.

Step 5: At the handset, reset the Date and Time.

http://www.vtechphones.com/vtechphones/index.cfm/support/general/frequently-asked-questions-faqs/


--
Jeff Liebermann
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

On Sat, 1 Oct 2011 14:49:45 -1000, "John Keiser"
wrote:

"0" messages appear.
I had tried the grand reset to no avail. Was hoping for an even grander
reset.
Phones function well enough.

Oh well. So much for the easy fixes.

Mostly curious about the service "port" as I my old stand alone answering
machine is working compatibly at the moment.

My guess(tm) is that it's a JTAG port used to load firmware and
initialized (serialize) the phone. I did some Googling but didn't
find anything specific for Vtech DECT phones. If you succeed in
finding or building an RS-232 converter for interfacing to the port,
you'll probably find a rather primitive command set, no help, no
menus, and cryptic commands and incantations. It will also lack any
easy way to recover from mistakes. Y're welcome to try it, but
methinks it's not worth the effort. However, you might want to open
the base and inspect the base for crappy soldering.

--
Jeff Liebermann
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

Ah! Yes, they are likely JTAG ports. Beyond my ability to tinker with.
Solder joints "looked" ok when I opened the base but there is a flex cable
connector I may explore in the interest of good fun.
Thanks.



"Jeff Liebermann" wrote in message
...
On Sat, 1 Oct 2011 14:49:45 -1000, "John Keiser"
wrote:

"0" messages appear.
I had tried the grand reset to no avail. Was hoping for an even grander
reset.
Phones function well enough.

Oh well. So much for the easy fixes.

Mostly curious about the service "port" as I my old stand alone answering
machine is working compatibly at the moment.

My guess(tm) is that it's a JTAG port used to load firmware and
initialized (serialize) the phone. I did some Googling but didn't
find anything specific for Vtech DECT phones. If you succeed in
finding or building an RS-232 converter for interfacing to the port,
you'll probably find a rather primitive command set, no help, no
menus, and cryptic commands and incantations. It will also lack any
easy way to recover from mistakes. Y're welcome to try it, but
methinks it's not worth the effort. However, you might want to open
the base and inspect the base for crappy soldering.

--
Jeff Liebermann
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558