Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


** A rather new looking Marshall " MA100H " valve head landed on my bench
today - but it looked a bit different. On the back it says " Made in Vietnam
" - so this is the first non UK made ( ie assembled) Marshall, at least
that I have ever seen.

The amp was silent, valves all lit up but no output whatsoever and no extra
current draw when the Standby switch was closed. OK - so where is the damn
HT fuse ? Nothing on the back so it must be inside - another first for a
Marshall valve amp. On the PCB is a 630mA delay fuse - very blown -
fitting a new one got the amp running.

Bit of poking about finds that both 1/4 inch QCs on the PCB used for output
valve grid drive are very loose - easy fixed. But was this the cause of
fuse blowing? Nope.

That 630 mA HT fuse should be 1 amp at least, since it is fitted in the
secondary of the PT. On test, the fuse had to pass just over 1 amp rms when
the amp is over-driven. The primary AC current draw is 2 amps rms at the
same time ( ie 480VA) .

On sine wave test, there is significant crossover distortion on the CRO
screen at 1/2 output and above. The bias setting seemed OK - there are two
trims inside and a pair of 1 ohm resistors in each pair of output valve
cathodes.

On checking the screen B+ supply, the cause is simple. There is no filter
choke of course ( what are they ?) and instead a 470 ohm ,7W resistor. So
the screen B+ supply falls like a rock soon as the amp is driven. Guess
this helps the crappy Chinese EL34s to survive overdriving.

Besides the above bad points, there are lots more.

The AC tranny is undersized - it looks like a 250VA type and needs to be
400VA to withstand hard use in this amp. Even sitting on the bench with a
605mA idle current from the AC supply, the internal temp rise is almost 40
degrees C. A couple of hours of heavy metal on a warm night will see it off.

The same * ridiculously fragile* plastic shaft pots as used on other recent
Marshalls have been fitted - one light bump on the knob = nasty
intermittent fault.

There is no AC voltage selector fitted and no internal option either,
another first in a Marshall valve head. All the fasteners are metric too,
not one single concession in sight to the brand's UK origin.

There ARE two small screw-in bulbs ( labelled 12V ) fitted inside the
cabinet that illuminate the whole chassis and the "Marshall" logo through
the open weave cloth. These are not ordinary 12 volt dial lamps but special
dual, orange LEDs - one chip connected for each polarity when fed with AC.

Next the these is a non Accutronics ( Belton ?) reverb tank.

All the jack sockets ( 7 of them ) are very fragile, PCB mount types.

Every single part in the amp looks like it came either from China, Korea or
Taiwan and then assembled in Vietnam.

Good points:
--------------

The 4 x EL34 output valves and the 12AX7 PI are on ceramic sockets, hand
wired to the two trannys and the PCB.

The main PCB looks like it is easy to get lose and invert for servicing.

The amp is pretty cheap to buy.

But a used example from the 1980s is a way better product, full of UK made
transformers and other parts that have proved their ability to survive in a
Marshall.



..... Phil





  #2   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 31
Default Vietnamese Marshall

On Apr 28, 1:39*pm, "Phil Allison" wrote:
** A rather new looking Marshall " MA100H " valve head landed on my bench
today - but it looked a bit different. On the back it says " Made in Vietnam
" *- *so this is the first non UK made ( ie assembled) Marshall, at least
that I have ever seen.

The amp was silent, valves all lit up but no output whatsoever and no extra
current draw when the Standby switch was closed. OK - so where is the damn
HT fuse ? Nothing on the back so it must be inside - another first for a
Marshall valve amp. On the PCB is a 630mA delay fuse - *very blown -
fitting a new one got the amp running.

Bit of poking about finds that both 1/4 inch QCs on the PCB used for output
valve grid drive are very loose *- easy fixed. But was this the cause of
fuse blowing? *Nope.

That 630 mA HT fuse should be 1 amp at least, since it is fitted in the
secondary of the PT. *On test, the fuse had to pass just over 1 amp rms when
the amp is over-driven. *The primary AC current draw is 2 amps rms at the
same time ( ie 480VA) .

On sine wave test, there is significant crossover distortion on the CRO
screen at 1/2 output and above. *The bias setting seemed OK - *there are two
trims inside and a pair of 1 ohm resistors in each pair of output valve
cathodes.

On checking the screen B+ supply, the cause is simple. There is no filter
choke of course ( what are they ?) and instead a 470 ohm ,7W resistor. So
the screen B+ supply falls like a rock soon as the amp is driven. *Guess
this helps the crappy Chinese EL34s to survive overdriving.

Besides the above bad points, there are lots more.

The AC tranny is undersized *- *it looks like a 250VA type and needs to be
400VA to withstand hard use in this amp. Even sitting on the bench with a
605mA idle current from the AC supply, the internal temp rise is almost 40
degrees C. A couple of hours of heavy metal on a warm night will see it off.

The same * ridiculously fragile* *plastic shaft pots as used on other recent
Marshalls have been fitted *- *one light bump on the knob = *nasty
intermittent fault.

There is no AC voltage selector fitted and no internal option either,
another first in a Marshall valve head. All the fasteners are metric too,
not one single concession in sight to the brand's UK origin.

There ARE two small screw-in bulbs ( labelled 12V ) fitted inside the
cabinet that illuminate the whole chassis and the "Marshall" logo through
the open weave cloth. *These are not ordinary 12 volt dial lamps but special
dual, orange LEDs *- one chip connected for each polarity when fed with AC.

Next the these is a non Accutronics ( Belton ?) reverb tank.

All the jack sockets ( 7 of them ) are very fragile, PCB mount types.

Every single part in the amp looks like it came either from China, Korea or
Taiwan and then assembled in Vietnam.

Good points:
--------------

The 4 x EL34 output valves and the 12AX7 PI are on ceramic sockets, hand
wired to the two trannys and the PCB.

The main PCB looks like it is easy to get lose and invert for servicing.

The amp is pretty cheap to buy.

But a used example from the 1980s is a way better product, full of UK made
transformers and other parts that have proved their ability to survive in a
Marshall.

.... *Phil


Good info. Haven't had one of these cross my path yet. Just finished
up on a DSL100 that had to have the main pcb replaced due to the bias
instability issue caused by crappy board material. The replacements
look to be FR4 or similar good quality stuff.
  #3   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 818
Default Vietnamese Marshall



"Phil Allison" wrote in message
...

** A rather new looking Marshall " MA100H " valve head landed on my bench
today - but it looked a bit different. On the back it says " Made in
Vietnam " - so this is the first non UK made ( ie assembled) Marshall,
at least that I have ever seen.

The amp was silent, valves all lit up but no output whatsoever and no
extra current draw when the Standby switch was closed. OK - so where is
the damn HT fuse ? Nothing on the back so it must be inside - another
first for a Marshall valve amp. On the PCB is a 630mA delay fuse - very
blown - fitting a new one got the amp running.

Bit of poking about finds that both 1/4 inch QCs on the PCB used for
output valve grid drive are very loose - easy fixed. But was this the
cause of fuse blowing? Nope.

That 630 mA HT fuse should be 1 amp at least, since it is fitted in the
secondary of the PT. On test, the fuse had to pass just over 1 amp rms
when the amp is over-driven. The primary AC current draw is 2 amps rms at
the same time ( ie 480VA) .

On sine wave test, there is significant crossover distortion on the CRO
screen at 1/2 output and above. The bias setting seemed OK - there are
two trims inside and a pair of 1 ohm resistors in each pair of output
valve cathodes.

On checking the screen B+ supply, the cause is simple. There is no filter
choke of course ( what are they ?) and instead a 470 ohm ,7W resistor. So
the screen B+ supply falls like a rock soon as the amp is driven. Guess
this helps the crappy Chinese EL34s to survive overdriving.

Besides the above bad points, there are lots more.

The AC tranny is undersized - it looks like a 250VA type and needs to be
400VA to withstand hard use in this amp. Even sitting on the bench with a
605mA idle current from the AC supply, the internal temp rise is almost 40
degrees C. A couple of hours of heavy metal on a warm night will see it
off.

The same * ridiculously fragile* plastic shaft pots as used on other
recent Marshalls have been fitted - one light bump on the knob = nasty
intermittent fault.

There is no AC voltage selector fitted and no internal option either,
another first in a Marshall valve head. All the fasteners are metric too,
not one single concession in sight to the brand's UK origin.

There ARE two small screw-in bulbs ( labelled 12V ) fitted inside the
cabinet that illuminate the whole chassis and the "Marshall" logo through
the open weave cloth. These are not ordinary 12 volt dial lamps but
special dual, orange LEDs - one chip connected for each polarity when fed
with AC.

Next the these is a non Accutronics ( Belton ?) reverb tank.

All the jack sockets ( 7 of them ) are very fragile, PCB mount types.

Every single part in the amp looks like it came either from China, Korea
or Taiwan and then assembled in Vietnam.

Good points:
--------------

The 4 x EL34 output valves and the 12AX7 PI are on ceramic sockets, hand
wired to the two trannys and the PCB.

The main PCB looks like it is easy to get lose and invert for servicing.

The amp is pretty cheap to buy.

But a used example from the 1980s is a way better product, full of UK made
transformers and other parts that have proved their ability to survive in
a Marshall.



.... Phil







I've an Ampeg SVT Classic here thats "manufactured in Vietnam".

Have to say the build quality seems good. The pots and sockets even seem to
be the retro style chunky Western parts.
I've seen quite a few of these now, never noticed the Vietnam connection
before, but they have always seemed to be solidly built.

I got 340 Watts out of the 6 x Sovtek 6550's today.



Gareth.

  #4   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"boardjunkie1"

Good info. Haven't had one of these cross my path yet. Just finished
up on a DSL100 that had to have the main pcb replaced due to the bias
instability issue caused by crappy board material. The replacements
look to be FR4 or similar good quality stuff.


** Seen that problem a few times - it's an absolute nightmare.

Marshall should make new PCBs available for free.


..... Phil


  #5   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Phil Allison"

** A rather new looking Marshall " MA100H " valve head landed on my bench
today - but it looked a bit different.



** Anyone located a schem for this POS on the net ??



.... Phil






  #6   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Phil Allison"

On the PCB is a 630mA delay fuse - very blown - fitting a new one got the
amp running.

That 630 mA HT fuse should be 1 amp at least, since it is fitted in the
secondary of the PT. On test, the fuse had to pass just over 1 amp rms
when the amp is over-driven.



** Just for clarity - the 630mA delay fuse was as fitted in the factory and
as labelled on the PCB.


..... Phil


  #7   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Vietnamese Marshall



"Phil Allison" wrote in message
...

"Phil Allison"

** A rather new looking Marshall " MA100H " valve head landed on my bench
today - but it looked a bit different.



** Anyone located a schem for this POS on the net ??



... Phil


I have three different issue numbers of schematics for the MA100, but none
seem to identify specifically an MA100 "H". If they are any use to you,
contact me off-group.

Arfa

  #8   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Arfa Daily"

I have three different issue numbers of schematics for the MA100, but none
seem to identify specifically an MA100 "H". If they are any use to you,
contact me off-group.



** Marshall sell ( note not make) an MA100H and an MA100C.

H = head and C = combo.

Decades ago, H-H made an amp called the MA100.


...... Phil









  #9   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Vietnamese Marshall



"Phil Allison" wrote in message
...

"Arfa Daily"

I have three different issue numbers of schematics for the MA100, but
none seem to identify specifically an MA100 "H". If they are any use to
you, contact me off-group.



** Marshall sell ( note not make) an MA100H and an MA100C.

H = head and C = combo.

Decades ago, H-H made an amp called the MA100.


..... Phil



So are my schematics for the Marshall MA100 any use to you ? If so, contact
me and I'll send them to you ...

Arfa

  #10   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Arfa Daily"
"Phil Allison"

I have three different issue numbers of schematics for the MA100, but
none seem to identify specifically an MA100 "H". If they are any use to
you, contact me off-group.


** Marshall sell ( note not make) an MA100H and an MA100C.

H = head and C = combo.

Decades ago, H-H made an amp called the MA100.


So are my schematics for the Marshall MA100 any use to you ? If so,
contact me and I'll send them to you ...



** You can send them to " " if you like.


...... Phil








  #11   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Vietnamese Marshall



"Phil Allison" wrote in message
...

"Arfa Daily"
"Phil Allison"

I have three different issue numbers of schematics for the MA100, but
none seem to identify specifically an MA100 "H". If they are any use to
you, contact me off-group.

** Marshall sell ( note not make) an MA100H and an MA100C.

H = head and C = combo.

Decades ago, H-H made an amp called the MA100.


So are my schematics for the Marshall MA100 any use to you ? If so,
contact me and I'll send them to you ...



** You can send them to " " if you like.


..... Phil


Done.

Arfa

  #12   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Arfa Daily"

So are my schematics for the Marshall MA100 any use to you ? If so,
contact me and I'll send them to you ...



** You can send them to " " if you like.


Done.


** Thanks.

I'll let you know if they are for the same amp.


...... Phil




  #13   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Vietnamese Marshall



"Phil Allison" wrote in message
...

"Arfa Daily"

So are my schematics for the Marshall MA100 any use to you ? If so,
contact me and I'll send them to you ...


** You can send them to " " if you like.


Done.


** Thanks.

I'll let you know if they are for the same amp.


..... Phil



OK. Noted.

Arfa

  #16   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Arfa Daily"
"Phil Allison"

I'll let you know if they are for the same amp.

OK. Noted.


** I have all the schems now and they are certainly for the same amp.

Only thing I can spot different is that 630mA HT fuse shown in the output
of the bridge rectifier where I see it fitted in the AC input. Makes no
difference to the rms current flow in the part.


Fair enough. I'll know if one crosses my bench ...



** Update: On careful perusing of the schems, I see a more differences
compared to the Vietnamese one I have.

1. The Vietnamese have used 12V LED bulbs instead of 12 volt filament
lamps.

2. The power and output transformers carry quite different numbers.

3. The EL34s have their heaters wired in parallel rather than series
parallel.


The Vietnamese Marshalls seem to be special versions or clones of the
similar UK models.


..... Phil





  #17   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Vietnamese Marshall



"Phil Allison" wrote in message
...

"Arfa Daily"
"Phil Allison"

I'll let you know if they are for the same amp.

OK. Noted.


** I have all the schems now and they are certainly for the same amp.

Only thing I can spot different is that 630mA HT fuse shown in the
output of the bridge rectifier where I see it fitted in the AC input.
Makes no difference to the rms current flow in the part.


Fair enough. I'll know if one crosses my bench ...



** Update: On careful perusing of the schems, I see a more differences
compared to the Vietnamese one I have.

1. The Vietnamese have used 12V LED bulbs instead of 12 volt filament
lamps.

2. The power and output transformers carry quite different numbers.

3. The EL34s have their heaters wired in parallel rather than series
parallel.


The Vietnamese Marshalls seem to be special versions or clones of the
similar UK models.


.... Phil





Interesting. As Vietnam is your end of the world, I wonder if they are a
version specially assembled there for the Oz market, to avoid the costs of
shipping such heavy items all the way from the UK. I'll see if I can probe
around any Marshall contacts to find out if they know anything.

Arfa

  #18   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 31
Default Vietnamese Marshall

On May 2, 2:10*am, "Arfa Daily" wrote:
"Phil Allison" wrote in message

...











"Arfa Daily"
"Phil Allison"


I'll let you know if they are for the same amp.


OK. Noted.


** I have all the schems now and they are certainly for the same amp.


Only thing I can spot different is that 630mA HT fuse shown in the
output of the bridge rectifier where I see it fitted in the AC input.
Makes no difference to the rms current flow in the part.


Fair enough. I'll know if one crosses my bench ...


** Update: On careful perusing of the schems, I see a more differences
compared to the Vietnamese one I have.


1. *The Vietnamese have used 12V LED bulbs instead of 12 volt filament
lamps.


2. *The power and output transformers carry quite different numbers.


3. *The EL34s have their heaters wired in parallel rather than series
parallel.


The Vietnamese Marshalls seem to be special versions or clones of the
similar UK models.


.... *Phil


Interesting. As Vietnam is your end of the world, I wonder if they are a
version specially assembled there for the Oz market, to avoid the costs of
shipping such heavy items all the way from the UK. I'll see if I can probe
around any Marshall contacts to find out if they know anything.

Arfa


Mind beaming a copy of that schemo in this direction?
  #19   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Arfa Daily"

The Vietnamese Marshalls seem to be special versions or clones of the
similar UK models.

Interesting. As Vietnam is your end of the world, I wonder if they are a
version specially assembled there for the Oz market, to avoid the costs of
shipping such heavy items all the way from the UK.



** No way.

Vietnam made MA100H and MA100C amps are sold world wide in 235V and 120V
versions - as Google search will proves.

Far more likely, initial assembly began the UK a couple of years ago and
then was shifted to Vietnam cos they could do it cheaper even than the
Chinese.



..... Phil



  #20   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,716
Default Vietnamese Marshall


"Arfa Daily"


Interesting. As Vietnam is your end of the world, I wonder if they are a
version specially assembled there for the Oz market,



** See the "Overview" on page 2 of the pdf.

http://www.marshallamps.com/download...a-handbook.pdf


Also note the pic of the back panel and the specs on page 4 of the pdf.


..... Phil








  #21   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Vietnamese Marshall



"boardjunkie1" wrote in message
...
On May 2, 2:10 am, "Arfa Daily" wrote:
"Phil Allison" wrote in message

...











"Arfa Daily"
"Phil Allison"


I'll let you know if they are for the same amp.


OK. Noted.


** I have all the schems now and they are certainly for the same amp.


Only thing I can spot different is that 630mA HT fuse shown in the
output of the bridge rectifier where I see it fitted in the AC input.
Makes no difference to the rms current flow in the part.


Fair enough. I'll know if one crosses my bench ...


** Update: On careful perusing of the schems, I see a more differences
compared to the Vietnamese one I have.


1. The Vietnamese have used 12V LED bulbs instead of 12 volt filament
lamps.


2. The power and output transformers carry quite different numbers.


3. The EL34s have their heaters wired in parallel rather than series
parallel.


The Vietnamese Marshalls seem to be special versions or clones of the
similar UK models.


.... Phil


Interesting. As Vietnam is your end of the world, I wonder if they are a
version specially assembled there for the Oz market, to avoid the costs
of
shipping such heavy items all the way from the UK. I'll see if I can
probe
around any Marshall contacts to find out if they know anything.

Arfa


Mind beaming a copy of that schemo in this direction?


'Tis beamed ... Let me know if any probs

Arfa

  #22   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 31
Default Vietnamese Marshall

On May 2, 11:54*am, "Arfa Daily" wrote:
"boardjunkie1" wrote in message

...









On May 2, 2:10 am, "Arfa Daily" wrote:
"Phil Allison" wrote in message


...


"Arfa Daily"
"Phil Allison"


I'll let you know if they are for the same amp.


OK. Noted.


** I have all the schems now and they are certainly for the same amp.


Only thing I can spot different is that 630mA HT fuse shown in the
output of the bridge rectifier where I see it fitted in the AC input.
Makes no difference to the rms current flow in the part.


Fair enough. I'll know if one crosses my bench ...


** Update: On careful perusing of the schems, I see a more differences
compared to the Vietnamese one I have.


1. *The Vietnamese have used 12V LED bulbs instead of 12 volt filament
lamps.


2. *The power and output transformers carry quite different numbers.


3. *The EL34s have their heaters wired in parallel rather than series
parallel.


The Vietnamese Marshalls seem to be special versions or clones of the
similar UK models.


.... *Phil


Interesting. As Vietnam is your end of the world, I wonder if they are a
version specially assembled there for the Oz market, to avoid the costs
of
shipping such heavy items all the way from the UK. I'll see if I can
probe
around any Marshall contacts to find out if they know anything.


Arfa


Mind beaming a copy of that schemo in this direction?


'Tis beamed ... *Let me know if any probs

Arfa


Right ahn...got it. Thanks bud...
  #23   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Vietnamese Marshall



"boardjunkie1" wrote in message
...
On May 2, 11:54 am, "Arfa Daily" wrote:
"boardjunkie1" wrote in message

...









On May 2, 2:10 am, "Arfa Daily" wrote:
"Phil Allison" wrote in message


...


"Arfa Daily"
"Phil Allison"


I'll let you know if they are for the same amp.


OK. Noted.


** I have all the schems now and they are certainly for the same
amp.


Only thing I can spot different is that 630mA HT fuse shown in the
output of the bridge rectifier where I see it fitted in the AC
input.
Makes no difference to the rms current flow in the part.


Fair enough. I'll know if one crosses my bench ...


** Update: On careful perusing of the schems, I see a more
differences
compared to the Vietnamese one I have.


1. The Vietnamese have used 12V LED bulbs instead of 12 volt
filament
lamps.


2. The power and output transformers carry quite different numbers.


3. The EL34s have their heaters wired in parallel rather than
series
parallel.


The Vietnamese Marshalls seem to be special versions or clones of
the
similar UK models.


.... Phil


Interesting. As Vietnam is your end of the world, I wonder if they are
a
version specially assembled there for the Oz market, to avoid the
costs
of
shipping such heavy items all the way from the UK. I'll see if I can
probe
around any Marshall contacts to find out if they know anything.


Arfa


Mind beaming a copy of that schemo in this direction?


'Tis beamed ... Let me know if any probs

Arfa


Right ahn...got it. Thanks bud...


Welcome ...

Arfa

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
First Marshall use of PbF ? / Test for PbF N_Cook Electronics Repair 3 March 25th 10 04:31 PM
Marshall AVT50 N_Cook Electronics Repair 1 December 15th 08 09:29 PM
Marshall JCM 2000 N_Cook Electronics Repair 8 November 20th 08 11:13 AM
name of a vietnamese hardwood [email protected] Woodworking 1 October 14th 06 05:09 PM
Marshall G80R CD redamp75 Electronics Repair 1 February 3rd 05 04:11 AM


All times are GMT +1. The time now is 03:40 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"