Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to sci.electronics.repair
|
|||
|
|||
Set Top Box connection to a TV (Dick Smith Electronics G1185)
Hi,
I have a 2 year old set top box (Dick Smith Electronics G1185) which I understand recvieves digital TV stations and converts the signal suitable for an analogue TV. My TV is quite old so it is basically a VHF receiver although it can receive one UHF channel 28. How do I connect the set top box to my TV? Perhaps you have this model? The back of the set top box has connects labelled: TV Arial TV/VCR ANT INT TV OUT RS232 L R Video Out SPDIF SVIDEO I assume that I connect my indoor arial to the "TV Arial" and my TV to "TV/VCR". What TV channel do I tune my TV to get the output signal. Needless to say I have lost the manual. I have tried channel 3 which is an old standard for VCRs I have had in the past. Thanks for any help. |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Set Top Box connection to a TV (Dick Smith Electronics G1185)
On Sun, 2 May 2010 21:23:27 -0700 (PDT), wrote:
Hi, I have a 2 year old set top box (Dick Smith Electronics G1185) which I understand recvieves digital TV stations and converts the signal suitable for an analogue TV. My TV is quite old so it is basically a VHF receiver although it can receive one UHF channel 28. Does it get channel 3 or 4? That's all you need. Set the box on 3 or 4 (there's a switch somewhere proobably.) and set the tv to the same channel. If all the connections have been made and you have plugged in the set top box and turned it on and the tv on, do you see anything on the tv? If not, set the box to the other number and set the tv to the same channel. If you can't find any switch, just connect and try channels 3 and 4 on the tv. How do I connect the set top box to my TV? Perhaps you have this model? The back of the set top box has connects labelled: TV Arial Connect an aerial. If your stations are near, within 10 or 20 miles, you can probalby just put a thin stiff wire in the center hole of the connector and stretch the wire out. Make it at least 3 feet long but maybe 6 or 7 feet would be better. For info on how many stations you should be able to get and what direction they are from where your tv is, check out www.tvfool.com . TV/VCR Connect a piece of co-axial cable from here to your tv. Does your tv have a connector like the one here? If so no problem . How old is your old tv? Does it have a knob to turn to change stations or just up and down buttons, or numeric buttons, like you used to press 1 and 3 to go to channel 13. And you press 3 to go to 3? If it's the latter, it almost surely has a co-axial connector on the back. If it's the former, a knob to turn to change channels, they can get dirty and sometimes not work well on a given channel. Try holding the knob a little bit off the place it comes to rest and see if it works then, or if the static on the screen changes. If it won't work on 3 or 4 To clean the connections, turn the knob back and forth through channels 3 and 4 a few times. That can help a lot. ANT INT It has both this and TV Arial? Do they look different? What do they look like? TV OUT RS232 L R Video Out SPDIF SVIDEO If your tv is old, I doubt you have an svideo jack on it. Is your tv stereo. Does it have RCA jacks. (See images.google.com to see what an RCA jack looks like.) What connections do you have on your tv. What are they labeled? How many of them physically resemble any of these last 7 on your box? I assume that I connect my indoor arial to the "TV Arial" and my TV to "TV/VCR". What TV channel do I tune my TV to get the output signal. Needless to say I have lost the manual. I have tried channel 3 which is an old standard for VCRs I have had in the past. Thanks for any help. -- Posters should say what U,S. state if any they live in. Why do so many keep their state as secret as their own name? IANAL. That is, I am not a lawyer. |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Set Top Box connection to a TV (Dick Smith Electronics G1185)
Does it get channel 3 or 4? That's all you need. Set the box on 3 or 4 (there's a switch somewhere proobably.) and set the tv to the same channel. If all the connections have been made and you have plugged in the set top box and turned it on and the tv on, do you see anything on the tv? If not, set the box to the other number and set the tv to the same channel. If you can't find any switch, just connect and try channels 3 and 4 on the tv. The TV does get channel 3 & 4. I did tune the TV to 3 and 4 and I don't get anything although the front of the set top box shows "signal". The box does not have a switch which says 3 or 4. It has both this and TV Aerial? Do they look different? What do they look like? Both TV Aerial and ANT INT look the same - I think they are called BNC you know where a coax cable goes in. That is what is confusing If your tv is old, I doubt you have an svideo jack on it. Is your tv stereo. Does it have RCA jacks. (See images.google.com to see what an RCA jack looks like.) What connections do you have on your tv. What are they labeled? How many of them physically resemble any of these last 7 on your box? My TV does not have SVIDEO. It has "A/V" and when I around the back I see 4 connectors in that area. The top row is labelled "IN" and bottom row "OUT" and the first column is labelled "Audio" and "Video". I suppose the set top box is sending out stereo and the TV epects mono - I can probably plug either L(Left) or R(Right) into that connector and "Video out" to "video" and press "A/V" on my TV. So in summary I: Connected a indoor aerial to "TV Aerial" Connected the "TV/VCR" to TV's "ANT" Switched my TV to channels 1,3,4 but I don't get anything 1. Anyone have any ideas? 2. I guess the next thing would be to try it on A/V Thanks for any help |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Set Top Box connection to a TV (Dick Smith Electronics G1185)
2. I guess the next thing would be to try it on A/V ** The DSE set top box only outputs video signals - so you MUST use the AV inputs on your TV. ..... Phil |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Set Top Box connection to a TV (Dick Smith Electronics G1185)
In message , Phil Allison
writes 2. I guess the next thing would be to try it on A/V ** The DSE set top box only outputs video signals - so you MUST use the AV inputs on your TV. http://www.productreview.com.au/showitem.php?item_id=53445 This does say "Optional UHF Modulator, PAL G/I/K, NTSC". What 'optional' means is anyone's guess! [Turn off / Turn on?] But it obviously isn't Ch3 or 4. How come the VHF TV set can actually receive one UHF channel? Is that a special Australia 'feature'? If your TV set does have A/V inputs, you're better off using them instead of trying to get the set-top box output onto Ch28 (assuming you can). -- Ian |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Set Top Box connection to a TV (Dick Smith Electronics G1185)
On Mon, 3 May 2010 22:54:54 +0100, Ian Jackson wrote:
In message , Phil Allison writes 2. I guess the next thing would be to try it on A/V ** The DSE set top box only outputs video signals - so you MUST use the AV inputs on your TV. http://www.productreview.com.au/showitem.php?item_id=53445 This does say "Optional UHF Modulator, PAL G/I/K, NTSC". What 'optional' means is anyone's guess! [Turn off / Turn on?] But it obviously isn't Ch3 or 4. How come the VHF TV set can actually receive one UHF channel? Is that a special Australia 'feature'? Nah, years ago it was standard to use a modulator output (usually on VCRs) tuned to one of the low VHF channels. These days one expects to find A/V on a TV. Grant. -- http://bugs.id.au/ |
#7
Posted to sci.electronics.repair
|
|||
|
|||
Set Top Box connection to a TV (Dick Smith Electronics G1185)
"Ian Jackson" Phil Allison 2. I guess the next thing would be to try it on A/V ** The DSE set top box only outputs video signals - so you MUST use the AV inputs on your TV. http://www.productreview.com.au/showitem.php?item_id=53445 This does say "Optional UHF Modulator, PAL G/I/K, NTSC". What 'optional' means is anyone's guess! ** Obviously it is a *factory option* not fitted to the DSE boxes. ...... Phil |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
buy electronics, sell electronics , auction electronics new, used electronics marketplace rHnI | Electronics Repair | |||
Protection Diodes On the Dick Smith Meter | Electronics Repair | |||
Dick smith ESR meter ? Where to buy in the US? | Electronics Repair | |||
Low ohms, (Dick Smith ESR meter), measurement problems | Electronics Repair |