Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
LASER Galvo mirror adhesive
Mirrors keep falling off my "Cosmic Storm" Lightshow LASER. Not only the
galvanometer X Y scanners beam mirrors but the proximity switch mirrors inside the galvos themselves. I'm thinking of using high impact crazy glue or old NOS radio TV cement 9 (the red stuff) -Joe NOSPAM |
#2
Posted to sci.electronics.repair
|
|||
|
|||
LASER Galvo mirror adhesive
Joe wrote:
Mirrors keep falling off my "Cosmic Storm" Lightshow LASER. Not only the galvanometer X Y scanners beam mirrors but the proximity switch mirrors inside the galvos themselves. I'm thinking of using high impact crazy glue or old NOS radio TV cement 9 (the red stuff) -Joe NOSPAM Go to any Automotive Supply store and get their RearView mirror repair Kit !!! Yukio YANO |
#3
Posted to sci.electronics.repair
|
|||
|
|||
LASER Galvo mirror adhesive
"Joe" writes:
Mirrors keep falling off my "Cosmic Storm" Lightshow LASER. Not only the galvanometer X Y scanners beam mirrors but the proximity switch mirrors inside the galvos themselves. I'm thinking of using high impact crazy glue or old NOS radio TV cement 9 (the red stuff) DO NOT use Crazy glue. I'd suggest 2 part Epoxy. 5 minute Epoxy is probably adequate and can be removed more easily than the long cure type, though that's stronger. --- sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/ Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/ +Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm | Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html Important: Anything sent to the email address in the message header above is ignored unless my full name AND either lasers or electronics is included in the subject line. Or, you can contact me via the Feedback Form in the FAQs. |
#4
Posted to sci.electronics.repair
|
|||
|
|||
LASER Galvo mirror adhesive
"Sam Goldwasser" wrote in message ... "Joe" writes: Mirrors keep falling off my "Cosmic Storm" Lightshow LASER. Not only the galvanometer X Y scanners beam mirrors but the proximity switch mirrors inside the galvos themselves. I'm thinking of using high impact crazy glue or old NOS radio TV cement 9 (the red stuff) DO NOT use Crazy glue. I'd suggest 2 part Epoxy. 5 minute Epoxy is probably adequate and can be removed more easily than the long cure type, though that's stronger. Two surface-coat 'impact' adhesive might also be a good bet, as this has very instant 'grab' characteristics when both surfaces are dry and then brought together, but has the added advantage of retaining a degree of flexibility in the bond, which may be helpful where a mass is being thrown about with 'instantaneous' stops. Based on the same thinking, a superior quality silicone rubber compound might also work well. Arfa |
#5
Posted to sci.electronics.repair
|
|||
|
|||
LASER Galvo mirror adhesive
agreed,the silicone in a layer thin enough to capture surface deficencies
but not thick enough to allow for flexibility would be optimal. it bonds to glass easily and is waterproof. and easily cleaned up before it gels. th only dr wback is 24 hour cure time to full strength where the mirror must be held motionless or it will creep "Arfa Daily" wrote in message ... "Sam Goldwasser" wrote in message ... "Joe" writes: Mirrors keep falling off my "Cosmic Storm" Lightshow LASER. Not only the galvanometer X Y scanners beam mirrors but the proximity switch mirrors inside the galvos themselves. I'm thinking of using high impact crazy glue or old NOS radio TV cement 9 (the red stuff) DO NOT use Crazy glue. I'd suggest 2 part Epoxy. 5 minute Epoxy is probably adequate and can be removed more easily than the long cure type, though that's stronger. Two surface-coat 'impact' adhesive might also be a good bet, as this has very instant 'grab' characteristics when both surfaces are dry and then brought together, but has the added advantage of retaining a degree of flexibility in the bond, which may be helpful where a mass is being thrown about with 'instantaneous' stops. Based on the same thinking, a superior quality silicone rubber compound might also work well. Arfa |
#6
Posted to sci.electronics.repair
|
|||
|
|||
LASER Galvo mirror adhesive
In article UnFcj.1423$OH6.1253@trndny03,
Joe wrote: Mirrors keep falling off my "Cosmic Storm" Lightshow LASER. Not only the galvanometer X Y scanners beam mirrors but the proximity switch mirrors inside the galvos themselves. I'm thinking of using high impact crazy glue or old NOS radio TV cement 9 (the red stuff) I'm impressed with polyester glue for lots of general purpose use where the very highest strength isn't needed. It seems to bond to a larger variety of materials than many. The downside is it takes an hour or so to set enough to hold and 24 to get to full strength. Dunno about brands everywhere but one in the UK is Evostick Serious Glue. -- *He who laughs last has just realised the joke. Dave Plowman London SW To e-mail, change noise into sound. |
#7
Posted to sci.electronics.repair
|
|||
|
|||
LASER Galvo mirror adhesive
Thanks Sam, I tried all including windshield mirror repair kit.
Best fix is yes the smallest dab of 5 minute GC epoxy then re-adjust the Galvo brackets. And thanks to all who replied...the LASER is holding in action with the band Green Machine with a 30MW DPS @ 3.6 VDC http://www.greenmachineband.com/ -Joe "Sam Goldwasser" wrote in message ... "Joe" writes: Mirrors keep falling off my "Cosmic Storm" Lightshow LASER. Not only the galvanometer X Y scanners beam mirrors but the proximity switch mirrors inside the galvos themselves. I'm thinking of using high impact crazy glue or old NOS radio TV cement 9 (the red stuff) DO NOT use Crazy glue. I'd suggest 2 part Epoxy. 5 minute Epoxy is probably adequate and can be removed more easily than the long cure type, though that's stronger. --- sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/ Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/ +Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm | Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html Important: Anything sent to the email address in the message header above is ignored unless my full name AND either lasers or electronics is included in the subject line. Or, you can contact me via the Feedback Form in the FAQs. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Oval mirror - mirror leaning on tree.JPG (0/2) | Woodworking Plans and Photos | |||
fixing mirror - mirror screws and bushes | UK diy | |||
Remove Wall Mirror with Adhesive | Home Repair | |||
Mirror adhesive OK? | UK diy | |||
Interlocking Suspended Ceiling/Fixing Trunking - Self adhesive or Impact adhesive. | UK diy |