I have a 2 1/2 year old, 27" Sanyo DS27930 TV that began to
occasionally turn itself off last week, but now won't turn on at all -
it just makes a buzzing noise for a few seconds when I try to turn it
on, and then turns itself off. 9 months ago it fell off its stand onto
a carpeted floor, but worked fine after that until this problem
cropped up.

I'm trying to decide if I should repair or replace it. According to
Consumer Reports, "It doesn't make economic sense to repair
off-warranty ... conventional TV sets under 30 inches." Do the experts
here agree with Consumer Reports' recommendation, or should I pay
($40) for an estimate to see how much it would cost to have it
repaired?

TIA,
Harry

HarryB wrote:
I have a 2 1/2 year old, 27" Sanyo DS27930 TV that began to
occasionally turn itself off last week, but now won't turn on at all -
it just makes a buzzing noise for a few seconds when I try to turn it
on, and then turns itself off. 9 months ago it fell off its stand onto
a carpeted floor, but worked fine after that until this problem
cropped up.

I'm trying to decide if I should repair or replace it. According to
Consumer Reports, "It doesn't make economic sense to repair
off-warranty ... conventional TV sets under 30 inches." Do the experts
here agree with Consumer Reports' recommendation, or should I pay
($40) for an estimate to see how much it would cost to have it
repaired?

TIA,
Harry


You're probably looking at $100 or so for the repair and you could
expect a few more years out of it then. Only you can determine if that's
worth it.

If the $40 is deducted from the repair, and the repair is a simple one, then
it may pay to repair. Also, you have to consider that after the repair is
done, there is no guarantee of how long the rest of the set will last. The
average repair for most common faults in TV sets, with about 1 hour of
labour, can range from about $70 to $120 depending on the time and parts
involved.

Generally speaking, it does not pay to service any TV set or appliance
unless it is a fairly expensive device, it is less than about 3 years old,
and it has had very little use.

--

JANA
_____


"HarryB" wrote in message
...
I have a 2 1/2 year old, 27" Sanyo DS27930 TV that began to
occasionally turn itself off last week, but now won't turn on at all -
it just makes a buzzing noise for a few seconds when I try to turn it
on, and then turns itself off. 9 months ago it fell off its stand onto
a carpeted floor, but worked fine after that until this problem
cropped up.

I'm trying to decide if I should repair or replace it. According to
Consumer Reports, "It doesn't make economic sense to repair
off-warranty ... conventional TV sets under 30 inches." Do the experts
here agree with Consumer Reports' recommendation, or should I pay
($40) for an estimate to see how much it would cost to have it
repaired?

TIA,
Harry

100$ to do some soldering ? I do those for 35 or 40$ . It takes less
than an hour and i get the customer back many times over on other items
and they tell others .
The extra business far outweighs trying to rip people off .

Why are you assuming that anyone is ripping people off? Read the posts and
respond with something useful, if you have something useful to say.

Leonard

"Ken G." wrote in message
...
100$ to do some soldering ? I do those for 35 or 40$ . It takes less
than an hour and i get the customer back many times over on other items
and they tell others .
The extra business far outweighs trying to rip people off .


--------------------------------------------------------------------------------
I am using the free version of SPAMfighter for private users.
It has removed 3592 spam emails to date.
Paying users do not have this message in their emails.
Try SPAMfighter for free now!

Ken G. wrote:
100$ to do some soldering ? I do those for 35 or 40$ . It takes less
than an hour and i get the customer back many times over on other items
and they tell others .
The extra business far outweighs trying to rip people off .



Depends if it's JUST soldering, or if other work is needed. Often bad
solder joints pop other parts.

Ken G. wrote:

100$ to do some soldering ? I do those for 35 or 40$ . It takes less
than an hour and i get the customer back many times over on other items
and they tell others .
The extra business far outweighs trying to rip people off .

Well Ken, if you have a shop with overhead, employees to pay, manuals to
buy, and the usual "everybody gets to the money first" that's why it
cost more. If you running a hobby business out of your basement
that another issue.

Your not doing your customer a favor if your out of business in a year.
The shop my dad used to work at (now closed) it was a minimum $110
for TV's + parts.

The price of TV's has come down, but the cost of fixing them has not.

Bob

----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----

On 17 Mar, 04:58, HarryB wrote:
I have a 2 1/2 year old, 27" Sanyo DS27930 TV that began to
occasionally turn itself off last week, but now won't turn on at all -
it just makes a buzzing noise for a few seconds when I try to turn it
on, and then turns itself off. 9 months ago it fell off its stand onto
a carpeted floor, but worked fine after that until this problem
cropped up.

I'm trying to decide if I should repair or replace it. According to
Consumer Reports, "It doesn't make economic sense to repair
off-warranty ... conventional TV sets under 30 inches." Do the experts
here agree with Consumer Reports' recommendation, or should I pay
($40) for an estimate to see how much it would cost to have it
repaired?

TIA,
Harry

Always get a free quote. If your repair shop wont do that, find
another one. Backstreet type shops are often a lot cheaper, and often
the only worthwhile option with electronics.

The repair age is not dead yet, but theres now more thats not worth
repairing than is.


NT

wrote in message
oups.com...
On 17 Mar, 04:58, HarryB wrote:
I have a 2 1/2 year old, 27" Sanyo DS27930 TV that began to
occasionally turn itself off last week, but now won't turn on at all -
it just makes a buzzing noise for a few seconds when I try to turn it
on, and then turns itself off. 9 months ago it fell off its stand onto
a carpeted floor, but worked fine after that until this problem
cropped up.

I'm trying to decide if I should repair or replace it. According to
Consumer Reports, "It doesn't make economic sense to repair
off-warranty ... conventional TV sets under 30 inches." Do the experts
here agree with Consumer Reports' recommendation, or should I pay
($40) for an estimate to see how much it would cost to have it
repaired?

TIA,
Harry

Always get a free quote. If your repair shop wont do that, find
another one. Backstreet type shops are often a lot cheaper, and often
the only worthwhile option with electronics.

The repair age is not dead yet, but theres now more thats not worth
repairing than is.

Bad advice. A shop that gives free estimates or "backstreet" type shops are
often the most likey to rip you off or give you ineffective service IME.

Leonard

--------------------------------------------------------------------------------
I am using the free version of SPAMfighter for private users.
It has removed 3592 spam emails to date.
Paying users do not have this message in their emails.
Try SPAMfighter for free now!

On 18 Mar, 01:32, "Leonard Caillouet" wrote:
wrote in message
oups.com...

Always get a free quote. If your repair shop wont do that, find
another one. Backstreet type shops are often a lot cheaper, and often
the only worthwhile option with electronics.

The repair age is not dead yet, but theres now more thats not worth
repairing than is.

Bad advice. A shop that gives free estimates or

I never recommend free estimates. A shop that only gives estimates is
generally not satisfactory imho (excepting dealership repair of high
price goods). An agreed price, ie a quote, is a basic of good business
practice.


"backstreet" type shops are
often the most likey to rip you off or give you ineffective service IME.

Dealerships charge unworkable prices most of the time, the nicer
independants do as often than not, backstreeters are a lot more likely
to get realistic IME. They have much lower overheads and need
business, plus they have cheaper ways of doing things, such as using
reclaimed parts.

It all depends where you are though, not everywhere's the same by any
means.

As for ineffective repairs, its just basic business sense when dealing
with unknowns, insist on seeing the item work before you pay.


NT

I agree with Meow. Also, Sanyo TV's are a good buy, & usually worth
repairing, if you get a free estimate, & have a
reasonable shop, or buddy in the business. If the TV worked after
being dropped, you MAY have a break in the main
board, likely be the flyback transformer, & it finally arced out
across the break, you may have a bad horizontal output.
Dani.



On Mar 17, 2:58 am, HarryB wrote:
I have a 2 1/2 year old, 27" Sanyo DS27930 TV that began to
occasionally turn itself off last week, but now won't turn on at all -
it just makes a buzzing noise for a few seconds when I try to turn it
on, and then turns itself off. 9 months ago it fell off its stand onto
a carpeted floor, but worked fine after that until this problem
cropped up.

I'm trying to decide if I should repair or replace it. According to
Consumer Reports, "It doesn't make economic sense to repair
off-warranty ... conventional TV sets under 30 inches." Do the experts
here agree with Consumer Reports' recommendation, or should I pay
($40) for an estimate to see how much it would cost to have it
repaired?

TIA,
Harry

On Mar 17, 12:58 am, HarryB wrote:
I'm trying to decide if I should repair or replace it. According to
Consumer Reports, "It doesn't make economic sense to repair
off-warranty ... conventional TV sets under 30 inches." Do the experts
here agree with Consumer Reports' recommendation, or should I pay
($40) for an estimate to see how much it would cost to have it
repaired?

I'll assume you're not inclined to attempt a repair yourself. If so,
then I would first determine what a new set will cost. These days,
even a new large-screen TV is fairly inexpensive--often less than
$300. If that isn't appealing, consider picking up a second hand set
(via Craigslist, for example).

Acquiring a second-hand set may seem laughable (and stingy), but
considering that high-definition TV is less than two years away, and
any standard format set you have now will shortly become obsolete
(unless you spend additional money for a yet-to-be-available converter
box), this is a reasonable option.

On the other hand, if you're mechanically inclined, you could open it
up and see if there's any obvious damage to an accessible component.
If you spot the problem, this may save the repair shop the time--and
your money--to diagnose the problem. I did this a few years back with
a set that would pulse on and off, sometimes in the middle of the
night (frightening!). I knew the problem was in the power supply, so
I took the set to a local repair shop and accurately describe the
symtoms. The repairman said, "Oh yeah, that's a common problem with
the XYZ transistor in the high-voltage line--Thanks!" The repair bill
was about $50. That was 17 years ago, and the set still works.

-Dave

In article . com,
says...
Acquiring a second-hand set may seem laughable (and stingy), but
considering that high-definition TV is less than two years away, and
any standard format set you have now will shortly become obsolete
(unless you spend additional money for a yet-to-be-available converter
box), this is a reasonable option.

Just to clarify, 2 years is the changeover to DIGITAL-only broadcasting.
There is no requirement that it be HD. Stations are free to use their
frequency allocation any way they want. Many just multi-cast multiple SD
feeds.

--
If there is a no_junk in my address, please REMOVE it before replying!
All junk mail senders will be prosecuted to the fullest extent of the
law!!
http://home.att.net/~andyross

"Andrew Rossmann" wrote in message
.net...
In article . com,
says...
Acquiring a second-hand set may seem laughable (and stingy), but
considering that high-definition TV is less than two years away, and
any standard format set you have now will shortly become obsolete
(unless you spend additional money for a yet-to-be-available converter
box), this is a reasonable option.

Just to clarify, 2 years is the changeover to DIGITAL-only broadcasting.
There is no requirement that it be HD. Stations are free to use their
frequency allocation any way they want. Many just multi-cast multiple SD
feeds.

--

Not exactly true. They AFAIK are required to have one unencrypted sub
channel. The rest is up to the station. The FCC recently made a rule change
that made The Tube go away. A crystal ball is required to know how it will
turn out.

Digital, including HD, is here. Analog goes away in 2 years. Have been
watching all the networks through antenna for 2-1/2 years. All the stations
I receive have HD in the evening(at least). I'd kick myself if I'd waited
this long to go digital.

In article ,
lid says...
Not exactly true. They AFAIK are required to have one unencrypted sub
channel. The rest is up to the station. The FCC recently made a rule change
that made The Tube go away. A crystal ball is required to know how it will
turn out.

Maybe "The Tube" is gone by you, but it's still here in the Chicago area
on WGN 9.2.

The FCC did recently rule that ALL subchannels have to comply with E/I
(Education/Information) rules. Before, it was assumed only the primary
needed to comply. I don't know if it's national, but here in Chicago,
they run some zoo program that talks about animals with jazz playing in
the background on Saturday mornings.

There are several stations here in the Chicago area that only carry one
or more SD's.

On the other hand, the main PBS station, WTTW-11, is going overboard. It
reduced it's HD from 1080i to 720p (for PBS-HD), and how has THREE SD
subchannels (simulcast of the analog, PBS Create, the new Spanish-
language V-me.)

--
If there is a no_junk in my address, please REMOVE it before replying!
All junk mail senders will be prosecuted to the fullest extent of the
law!!
http://home.att.net/~andyross

"Andrew Rossmann" wrote in message
. net...
In article ,
lid says...
Not exactly true. They AFAIK are required to have one unencrypted sub
channel. The rest is up to the station. The FCC recently made a rule
change
that made The Tube go away. A crystal ball is required to know how it
will
turn out.

Maybe "The Tube" is gone by you, but it's still here in the Chicago area
on WGN 9.2.

The FCC did recently rule that ALL subchannels have to comply with E/I
(Education/Information) rules. Before, it was assumed only the primary
needed to comply. I don't know if it's national, but here in Chicago,
they run some zoo program that talks about animals with jazz playing in
the background on Saturday mornings.


From posts in the HD group I'd guess still having The Tube is the exception.
Mostly pointing out that rules are still changing.

There are several stations here in the Chicago area that only carry one
or more SD's.


I said in my area. Sure you have SD channels but you also have all the HD
channels. Dayton,OH isn't exactly huge and has all HD. Small cities may have
SD only stations. Characterizing the nation as being mostly SD is wrong.

On the other hand, the main PBS station, WTTW-11, is going overboard. It
reduced it's HD from 1080i to 720p (for PBS-HD), and how has THREE SD
subchannels (simulcast of the analog, PBS Create, the new Spanish-
language V-me.)

--

I'm getting 3 PBS stations through cable. 2 of the stations are as you say
except the last SD is an Ohio channel. PQ is terrible on it. Not aware of
them making changes to HD here. The third channel from Cincinnati is HD and
one SD, 24/7. Great PQ. My HDTV is 720p so the extra bandwidth for the SD
subchannels would be a good thing. It's going to be different for everyone.

Captain Midnight wrote:

"Andrew Rossmann" wrote in message
.net...
In article . com,
says...
Acquiring a second-hand set may seem laughable (and stingy), but
considering that high-definition TV is less than two years away, and
any standard format set you have now will shortly become obsolete
(unless you spend additional money for a yet-to-be-available converter
box), this is a reasonable option.

Just to clarify, 2 years is the changeover to DIGITAL-only broadcasting.
There is no requirement that it be HD. Stations are free to use their
frequency allocation any way they want. Many just multi-cast multiple SD
feeds.

--

Not exactly true. They AFAIK are required to have one unencrypted sub
channel. The rest is up to the station. The FCC recently made a rule change
that made The Tube go away. A crystal ball is required to know how it will
turn out.

Digital, including HD, is here. Analog goes away in 2 years. Have been
watching all the networks through antenna for 2-1/2 years. All the stations
I receive have HD in the evening(at least). I'd kick myself if I'd waited
this long to go digital.


For some people that means all TV goes away in two years. There is
no way that I am going to buy a new HD TV set just to watch the same old
crap that I see right now. In fact, about the only TV I watch is the
news, and even it isn't worth paying for. I'll keep one TV and the DVD
player till one of them quit working, and have the cable turned off.


--
Service to my country? Been there, Done that, and I've got my DD214 to
prove it.
Member of DAV #85.

Michael A. Terrell
Central Florida

Michael A. Terrell wrote:
Captain Midnight wrote:

"Andrew Rossmann" wrote in message
st.net...

In article . com,
says...

Acquiring a second-hand set may seem laughable (and stingy), but
considering that high-definition TV is less than two years away, and
any standard format set you have now will shortly become obsolete
(unless you spend additional money for a yet-to-be-available converter
box), this is a reasonable option.

Just to clarify, 2 years is the changeover to DIGITAL-only broadcasting.
There is no requirement that it be HD. Stations are free to use their
frequency allocation any way they want. Many just multi-cast multiple SD
feeds.

--

Not exactly true. They AFAIK are required to have one unencrypted sub
channel. The rest is up to the station. The FCC recently made a rule change
that made The Tube go away. A crystal ball is required to know how it will
turn out.

Digital, including HD, is here. Analog goes away in 2 years. Have been
watching all the networks through antenna for 2-1/2 years. All the stations
I receive have HD in the evening(at least). I'd kick myself if I'd waited
this long to go digital.



For some people that means all TV goes away in two years. There is
no way that I am going to buy a new HD TV set just to watch the same old
crap that I see right now. In fact, about the only TV I watch is the
news, and even it isn't worth paying for. I'll keep one TV and the DVD
player till one of them quit working, and have the cable turned off.


I've also been thinking on the same lines. very simple basic TV and
internet./
I pay 158 a month for nothing but crap!. Old repeats over and over
again.
it's not worth it any more.
I would rather stop at block buster and watch a DVD commercial free.


--
"I'm never wrong, once i thought i was, but was mistaken"
Real Programmers Do things like this.
http://webpages.charter.net/jamie_5

Acquiring a second-hand set may seem laughable (and stingy), but
considering that high-definition TV is less than two years away, and
any standard format set you have now will shortly become obsolete
(unless you spend additional money for a yet-to-be-available converter
box), this is a reasonable option.



They've been available for years, digital satellite receivers and
digital cable boxes convert to analog TV output.

Hi!

I have a 2 1/2 year old, 27" Sanyo DS27930 TV that began to
occasionally turn itself off last week, but now won't turn on at all -
it just makes a buzzing noise for a few seconds when I try to turn it
on, and then turns itself off. 9 months ago it fell off its stand onto
a carpeted floor, but worked fine after that until this problem
cropped up.

I would at least investigate a repair. If you stop right now and take the
set to a competent repair shop, the problem should be easier and less
expensive to repair. Waiting until the set really blows up or fails to turn
on entirely will make the repair more difficult and expensive.

The only thing working against you is the fact that it was dropped. Even if
it fell onto the carpet from its stand, falling just the right way can cause
serious and not immediately evident damage to a device. Fortunately, if
damage was done, it would have been pretty obvious because the tube is by
far the most delicate component of the TV. If the picture was good when it
stopped working, then a repair is much more likely to be worthwhile.

William