Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
hi ppl, examining the printer paper feed operation with rear cover off
(19Kb) i can see paper is not being grabbed. it doesnt appear to be a dry rubber problem. more of the paper is being stopped by tabs (green arrows) and rolling bushes (red arrows). any ideas on what could be wrong? i have just bought new ink cartridges so i would like to keep this printer. thanks http://www.geocities.com/xamman19/arrowed_sm.JPG |
#2
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
xamman wrote:
hi ppl, examining the printer paper feed operation with rear cover off (19Kb) i can see paper is not being grabbed. it doesnt appear to be a dry rubber problem. more of the paper is being stopped by tabs (green arrows) and rolling bushes (red arrows). any ideas on what could be wrong? i have just bought new ink cartridges so i would like to keep this printer. thanks http://www.geocities.com/xamman19/arrowed_sm.JPG Normally the solution is to clean the draw rollers that pull the paper into the printer. I believe that HP suggests you use a cloth dampened with soapy water (dish soap works fine) to clean the rollers. I have also used alcohol to do this. On my printer you hold the dampened cloth so that it touches the roller and depress the form feed button on the printer. Stop when the roller completes a 360 degree cycle and do it to all the rollers. Also make sure you do not have too little or too much paper in the paper tray. |
#3
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
"Ken" wrote in message ... Normally the solution is to clean the draw rollers that pull the paper into the printer. I believe that HP suggests you use a cloth dampened with soapy water (dish soap works fine) to clean the rollers. I have also used alcohol to do this. On my printer you hold the dampened cloth so that it touches the roller and depress the form feed button on the printer. Stop when the roller completes a 360 degree cycle and do it to all the rollers. Also make sure you do not have too little or too much paper in the paper tray. Seems to be a common problem with Oki lasers. Any suggestions for 'softeners' for the rubber rollers? |
#4
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
i dont think it is a dirty roller as the rollers dont even get to
touch the paper. i could try putting more paper into the paper tray to see what happens |
#5
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
xamman wrote:
i dont think it is a dirty roller as the rollers dont even get to touch the paper. i could try putting more paper into the paper tray to see what happens Oh, I thought it was simply slipping. I believe that part of the paper tray is lifted during a feed operation. See if there is an obstruction at the point where the paper tray meets the printer or make sure the tray is inserted fully. Not sure however??? |
#6
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
i tried adding more paper. now at 1cm of paper in tray the printer
grabs a sheet each time. i closed the rear (as otherwise the paper would just be ejected out the back) and did some test prints. however i am noticing each page is emerging with the front end bent at the right (photo 13kb below) . what does this suggest to you? http://www.geocities.com/xamman19/bent.JPG thx |
#7
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
xamman wrote:
hi ppl, examining the printer paper feed operation with rear cover off (19Kb) i can see paper is not being grabbed. it doesnt appear to be a dry rubber problem. more of the paper is being stopped by tabs (green arrows) and rolling bushes (red arrows). any ideas on what could be wrong? i have just bought new ink cartridges so i would like to keep this printer. thanks http://www.geocities.com/xamman19/arrowed_sm.JPG From the picture, the paper feed rollers look quite worn ! My standard method for improving the pickup is to clean the rollers with a damp cloth and a spot of detergent. If that doesn't improve things, gently abrade the rubber with a nail board. Also if you look carefully you will see a cam that lifts the paper tray. Lack of lubrication causes severe wear. The effect is that you need to put more paper in the tray so that it is lifted up high enough for the feed rollers to grab. Use white grease for plastic on the surface of the cam. HTH -- Baron: |
#8
Posted to sci.electronics.repair
|
|||
|
|||
deskjet not grabbing paper- anyone solved this before?
xamman wrote:
i tried adding more paper. now at 1cm of paper in tray the printer grabs a sheet each time. i closed the rear (as otherwise the paper would just be ejected out the back) and did some test prints. however i am noticing each page is emerging with the front end bent at the right (photo 13kb below) . what does this suggest to you? http://www.geocities.com/xamman19/bent.JPG thx Baron has as good a suggestion as I could give. Look carefully at the paper tray, particularly the part that lifts. Also look at the rollers and see if there is any obstruction. Most of the time you can find some reason for a sheet feed failure, but you could be working with worn parts? |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
HP DeskJet 500 | Electronics Repair | |||
HP deskJet 980Cxi will not print | Electronics Repair | |||
OT - need some help/advice with grabbing data from a website | Metalworking | |||
HP DeskJet 660C | Electronics Repair | |||
HP deskjet -- does everything except print | Electronics Repair |