Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Slow start up
I have the following symptoms on my panasonic tx-w28r3
Slow start up, getting progressively worse. I understand this should be a dried out capacitor. Any ideas where to look? |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Slow start up
"z" wrote in message ups.com... I have the following symptoms on my panasonic tx-w28r3 Slow start up, getting progressively worse. I understand this should be a dried out capacitor. Any ideas where to look? Power supply. Suspect any small electrolytic positioned close to any component which runs hot in normal use, including nearby heatsinks. Arfa |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Slow start up
z ha escrito: I have the following symptoms on my panasonic tx-w28r3 Slow start up, getting progressively worse. I understand this should be a dried out capacitor. Any ideas where to look? euro3 chassis. be careful when poking around in the power supply. there are high voltages stored there, in the main filter capacitor which can give a nasty belt even when the unit is unplugged. If at all in doubt about your ability to handle this , or solder , get the set to a tech. -B |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Slow start up
"b" wrote in message oups.com... z ha escrito: I have the following symptoms on my panasonic tx-w28r3 Slow start up, getting progressively worse. I understand this should be a dried out capacitor. Any ideas where to look? euro3 chassis. be careful when poking around in the power supply. there are high voltages stored there, in the main filter capacitor which can give a nasty belt even when the unit is unplugged. If at all in doubt about your ability to handle this , or solder , get the set to a tech. -B Absolutely agreed Arfa |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Slow start up
b wrote: z ha escrito: I have the following symptoms on my panasonic tx-w28r3 Slow start up, getting progressively worse. I understand this should be a dried out capacitor. Any ideas where to look? euro3 chassis. be careful when poking around in the power supply. there are high voltages stored there, in the main filter capacitor which can give a nasty belt even when the unit is unplugged. If at all in doubt about your ability to handle this , or solder , get the set to a tech. -B What sort of high voltage, 220v ? Which capacitor is that, the big electrolytic one? I already poked around, and I am still here, so maybe it alright after all? |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Slow start up
"z" wrote in message oups.com... b wrote: z ha escrito: I have the following symptoms on my panasonic tx-w28r3 Slow start up, getting progressively worse. I understand this should be a dried out capacitor. Any ideas where to look? euro3 chassis. be careful when poking around in the power supply. there are high voltages stored there, in the main filter capacitor which can give a nasty belt even when the unit is unplugged. If at all in doubt about your ability to handle this , or solder , get the set to a tech. -B What sort of high voltage, 220v ? Which capacitor is that, the big electrolytic one? I already poked around, and I am still here, so maybe it alright after all? That's the cap. So long as the psu has started up, charge on that cap is not normally an issue, as when you power off, the primary side circuitry will keep drawing current from the cap until the voltage across it has dropped low enough that psu operation can no longer be sustained. The problem comes if the psu has not started up. That cap will be charged to the peak voltage of the line power - around 360v in the uk, but less in the US - and it will remain so after the power has been removed. A cap in good condition can stay charged enough to give you a nasty belt for hours, and in some cases days, after removal of power. Bear in mind also, that this voltage is derived directly from the line power, with no isolation or current limiting, other than the input fuse, so is potentially lethal. Arfa |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Fresh Start vs. Sta-bil | Home Repair | |||
Capacitor start motor help please | Metalworking | |||
DVD - Slow Motion | Electronics Repair | |||
Failing Fluorescent Fixtures | Home Repair | |||
Tecumseh HMSK-80 Hard to start, need help | Home Repair |