Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
What do people here use for heat shrink tubing?
I'm tired of using matches, and a butane pencil torch seems like overkill. -- Pierre, mon ami. Jetez encore un Scientologiste dans le baquet d'acide. - from a posting in alt.religion.scientology titled "France recommends dissolving Scientologists" |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
"David Nebenzahl" wrote in message .com... What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. I run the tip of my soldering iron over it if it small - otherwise I use a heat gun -- Pierre, mon ami. Jetez encore un Scientologiste dans le baquet d'acide. - from a posting in alt.religion.scientology titled "France recommends dissolving Scientologists" |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
I use a heat gun..
- Mike "David Nebenzahl" wrote in message .com... What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. -- Pierre, mon ami. Jetez encore un Scientologiste dans le baquet d'acide. - from a posting in alt.religion.scientology titled "France recommends dissolving Scientologists" |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
David Nebenzahl wrote in
.com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. -- Jim Yanik jyanik at kua.net |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
David Nebenzahl wrote:
What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. I find one of those long nozzled butane lighters used to light outdoor BBQ's etc. works well in most situations . Big flame to cover a good size area, but not too hot. Dan |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
Jim Yanik wrote:
David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) Dan |
#7
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
Dan spake thus:
Jim Yanik wrote: David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) I thought about a heat gun; we're talking about those things that are basically glorified blow dryers, right? Isn't that a little much just to heat a little bitty piece of tubing? Are there any "mini heat guns" available to heat smaller things? -- Pierre, mon ami. Jetez encore un Scientologiste dans le baquet d'acide. - from a posting in alt.religion.scientology titled "France recommends dissolving Scientologists" |
#8
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
David Nebenzahl wrote:
Dan spake thus: Jim Yanik wrote: David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) I thought about a heat gun; we're talking about those things that are basically glorified blow dryers, right? Isn't that a little much just to heat a little bitty piece of tubing? Are there any "mini heat guns" available to heat smaller things? Not that I'm aware of, the size doesn't matter, that's exactly what they're designed for amoung other things, it works better than anything else I've ever tried. |
#9
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
In article ,
David Nebenzahl wrote: Dan spake thus: Jim Yanik wrote: David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) I thought about a heat gun; we're talking about those things that are basically glorified blow dryers, right? Isn't that a little much just to heat a little bitty piece of tubing? Are there any "mini heat guns" available to heat smaller things? I think the real heat guns are considerably hotter than a hair dryer. They're the best thing in most circumstances. Someone suggested the tip of a soldering iron, which works, but I find the barrel works better. The tip is a tad *too* hot sometimes. |
#10
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
I use a heat gun that was designed for heat shrik tubing. Jerry G. ====== |
#11
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
On Wed, 03 May 2006 16:19:30 -0700, David Nebenzahl
put finger to keyboard and composed: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. Hair dryer. - Franc Zabkar -- Please remove one 'i' from my address when replying by email. |
#12
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
"Dan" wrote in message . .. David Nebenzahl wrote: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. I find one of those long nozzled butane lighters used to light outdoor BBQ's etc. works well in most situations . Big flame to cover a good size area, but not too hot. Dan I use a Black and Decker two heat paint stripper gun for the big stuff, and a butane flameless mini heatgun, for the small stuff, and have used both for years. The butane gun is actually a pencil gas torch, of the type that often has a catalytic soldering tip available for it. The heatgun accessory, is basically the same, in that the gas passes over a platinum wire catalyser, which glows red hot, and then exits as a stream of hot gas, from the nozzle. Intensity of the jet, and temperature, can both be controlled by the setting of the gas valve. It refills from a normal can of butane cigarette lighter gas. There are dedicated heatgun only tools as well. Look at http://www.autobarndeals.com/servlet...uns/Categories for examples Arfa |
#13
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
In article ,
David Nebenzahl wrote: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. Cheapest way is to get a dual heat setting hot air paint stripper gun from a DIY shed. They're often on offer for a very small sum. Only use on low power setting. Don't get a single heat setting one as they're rather too powerful. The pro types are expensive. They're smaller so might be better if using heat shrink inside an amp etc and they don't produce so much heat. But for cables etc, a paint stripper type on 1Kw or less output is fine. Some hairdriers can also be used if they have a nozzle to direct the airflow. -- *Even a blind pig stumbles across an acorn now and again * Dave Plowman London SW To e-mail, change noise into sound. |
#14
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
In article , David Nebenzahl wrote:
Dan spake thus: Jim Yanik wrote: David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) I thought about a heat gun; we're talking about those things that are basically glorified blow dryers, right? Isn't that a little much just to heat a little bitty piece of tubing? Are there any "mini heat guns" available to heat smaller things? I have an Ungar. You can probably buy one for $300. I also have a Weller station for about $900. The Ungar has been wonderfull and I bought it over 20 years ago for about $80. greg |
#16
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
David Nebenzahl wrote:
What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. A heat gun is the ideal choice and is quite inexpensive. But for quick jobs or when I'm away from the bench I often use a butane cigarette lighter (then give the heatshrunk a quick wipe to remove the soot). Tim -- Did I really still have that sig? |
#17
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
On Wed, 03 May 2006 18:52:53 -0700, David Nebenzahl
wrote: Dan spake thus: Jim Yanik wrote: David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) I thought about a heat gun; we're talking about those things that are basically glorified blow dryers, right? I think they are basically a blow dryer with the element closer to the end of the blower tube...blow dryers have pretty-well maxed out the wattage of a 120 VAC circuit. Tom Isn't that a little much just to heat a little bitty piece of tubing? Are there any "mini heat guns" available to heat smaller things? |
#18
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
I think the major difference between a hair dryer and a heat gun is
airflow.. A heat gun doesn't move nearly the volume of air that a hair dryer does. - Mike "Tom MacIntyre" wrote in message ... On Wed, 03 May 2006 18:52:53 -0700, David Nebenzahl wrote: Dan spake thus: Jim Yanik wrote: David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) I thought about a heat gun; we're talking about those things that are basically glorified blow dryers, right? I think they are basically a blow dryer with the element closer to the end of the blower tube...blow dryers have pretty-well maxed out the wattage of a 120 VAC circuit. Tom Isn't that a little much just to heat a little bitty piece of tubing? Are there any "mini heat guns" available to heat smaller things? |
#19
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
In article ,
David Nebenzahl wrote: heat a little bitty piece of tubing? Are there any "mini heat guns" available to heat smaller things? Not a butane pencil torch (sounds like a blowlamp!) but I use the side "exhaust port" of an Oryx Portasol butane soldering iron. Usually because I can't be bothered to change the (hot) soldering iron tip for the proper hot air blower attachment! In either case, you get a good stream of hot air, with no flame. Does just fine for small sleeving, might take a while for larger stuff though! -- --------------------------------------+------------------------------------ Mike Brown: mjb[at]pootle.demon.co.uk | http://www.pootle.demon.co.uk/ |
#22
Posted to sci.electronics.repair
|
|||
|
|||
Heat source for heat shrink
In article , Jim Yanik wrote:
(GregS) wrote in : In article , wrote: On Wed, 03 May 2006 18:52:53 -0700, David Nebenzahl wrote: Dan spake thus: Jim Yanik wrote: David Nebenzahl wrote in .com: What do people here use for heat shrink tubing? I'm tired of using matches, and a butane pencil torch seems like overkill. an electric heat gun. Harbor Freight sells them VERY inexpensively. I imagine some better hair dryers would also work. I have one of those HF guns. Also works fine but of course you have to plug it in somewhere ;-) I thought about a heat gun; we're talking about those things that are basically glorified blow dryers, right? I think they are basically a blow dryer with the element closer to the end of the blower tube...blow dryers have pretty-well maxed out the wattage of a 120 VAC circuit. The Ungar has a narrow opening and has different tips to control the flow some more. Its about 600 watts. Will melt solder at about 600 to 700 degrees. That was the Princess model;is it still being sold by Ungar? I don't know if its called Princess http://www.elexp.com/sdr_1095.htm |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Windows | Home Repair | |||
Steam Heat Costs | Home Repair | |||
prog. therm. and heat pump questions | Home Repair | |||
Brown's gas?? | Metalworking | |||
An air-soil solar sub-basement heat battery | Home Repair |