I don't know what to do now, I've had this router since August 02, and
over the weekend the speed control burned out for the 2nd time. It's
now stuck on HIGH.

It's now out of warranty (the first time it was a month out of warranty
and Dewalt covered the repair). I doubt they would cover it now, and
the speed control module is about $85 to replace it myself.

What would you do with this router? I'd hate to replace the control
again and have it burn out for a 3rd time... Should I just get one of
those speed controls which go between the router and outlet?

I had the same problem with a dewalt sander - after about 9 months, it
seemed to be stuck on high. I found I kept lowering and lowering the
setting, but it just kept turning faster and faster. And when I set the
sander to it's fastest setting - I thought it was going to take off!

My buddy at the tool shop replaced it free for me, but the next one did the
same thing in about the same time. I just gave up on DeWalt and I replaced
it with a high-end bosch unit - great machine - I give it a workout, and it
has worked perfectly for the past 2 years.

Personally, I would think about replacing the router with something made a
little better - don't spend good money after bad. The variable speed
controllers are ok for very occational use - they work by starving the motor
of energy - eventually doing damage.


Brian


"Larry Bud" wrote in message
oups.com...
I don't know what to do now, I've had this router since August 02, and
over the weekend the speed control burned out for the 2nd time. It's
now stuck on HIGH.

It's now out of warranty (the first time it was a month out of warranty
and Dewalt covered the repair). I doubt they would cover it now, and
the speed control module is about $85 to replace it myself.

What would you do with this router? I'd hate to replace the control
again and have it burn out for a 3rd time... Should I just get one of
those speed controls which go between the router and outlet?

Did you get a repair estimate from an authorized Dewalt repair center?
Have you written Dewalt?

I had a very pleasant experience with Dewalt after warranty repair. I
dropped my 18volt drill 10 feet onto the concrete and killed it. I
acknowledged this abuse to the repair center. They said they replaced
most of the guts of the drill, but what they really did was give me a
new model drill (even the chuck and case were new) for $39 total.

I guess I can count my lucky starts. I have the 621 router (4 years old
now) and never had a moment's problem. Maybe I don't use it enough.

Bob

"Larry Bud" wrote in message
oups.com...
I don't know what to do now, I've had this router since August 02, and
over the weekend the speed control burned out for the 2nd time. It's
now stuck on HIGH.

It's now out of warranty (the first time it was a month out of warranty
and Dewalt covered the repair). I doubt they would cover it now, and
the speed control module is about $85 to replace it myself.

What would you do with this router? I'd hate to replace the control
again and have it burn out for a 3rd time... Should I just get one of
those speed controls which go between the router and outlet?

For about double the price of the switch you can get a comparable brand
router. You know the old saying. Fool me once shame on you, fool me twice
shame on me. That said, I have 2 Bosch routers 1 is 16 years old and the
other is almost 6 years old and the only problems that I have had with
either unit is with the switches early in the game. Are you by any chance
over loading the router?

wrote:
Did you get a repair estimate from an authorized Dewalt repair
center?
Have you written Dewalt?

No, but I can order the electronic speed module for $85 online. It's
easy to replace (I checked it out).

For about double the price of the switch you can get a comparable
brand
router. You know the old saying. Fool me once shame on you, fool me
twice
shame on me. That said, I have 2 Bosch routers 1 is 16 years old
and the
other is almost 6 years old and the only problems that I have had
with
either unit is with the switches early in the game. Are you by any
chance
over loading the router?

I suppose I could be over loading it... but shouldn't there be
protection against that?

"Larry Bud" wrote in message
oups.com...
For about double the price of the switch you can get a comparable
brand
router. You know the old saying. Fool me once shame on you, fool me
twice
shame on me. That said, I have 2 Bosch routers 1 is 16 years old
and the
other is almost 6 years old and the only problems that I have had
with
either unit is with the switches early in the game. Are you by any
chance
over loading the router?

I suppose I could be over loading it... but shouldn't there be
protection against that?

Do you know of any universal motors that have thermal protection? The only
tool I have like that is a 20 year old 7.2 volt Makita right angle drill.
If I over load it, a little button pops out. From there only a few of my
induction motors have this protection feature.

"Do you know of any universal motors that have thermal protection?"

Good point Leon.

Larry, what have you been doing with your 621? I've got one that is
about 4 years old and never a problem. In fact I have 625, 12" SCMS,
palm sander, biscuit joiner, cordless trim saw, 14.4V drill (and two of
those at work), and an 18V drill. Never had a spot of problem with any
of them.

Dave wrote:
"Do you know of any universal motors that have thermal protection?"

Good point Leon.

Larry, what have you been doing with your 621? I've got one that is
about 4 years old and never a problem. In fact I have 625, 12" SCMS,
palm sander, biscuit joiner, cordless trim saw, 14.4V drill (and two
of
those at work), and an 18V drill. Never had a spot of problem with
any
of them.

All I was doing was running 1/4" spiral bit 1/4" deep in white oak. It
bogged down a little at a couple of points, but I slowed down, and it
cut fine.. Never even had a burn mark.

I suppose I could be over loading it... but shouldn't there be
protection against that?

Do you know of any universal motors that have thermal protection?
The only
tool I have like that is a 20 year old 7.2 volt Makita right angle
drill.

I know very little about what features are on what motors. But I
looked on Amazon and they state that one of the Bosch routers has
"overload protection". I would think that's the same thing.

But it's not the motor that is dying, it's the electronic speed
control.

"Larry Bud" wrote in message
ups.com...



I know very little about what features are on what motors. But I
looked on Amazon and they state that one of the Bosch routers has
"overload protection". I would think that's the same thing.

That could simply be a feed back from the speed control switch. If the
motor bogs down the switch feeds more current to speed the motor back up.
If the motor slows or stalls it coud burn up. This is helpful but not a
guarantee. If the motor draws too much current through the switch it could
burn out the circuitry in the switch and or motor. Better would be to have
an additional themal reset switch which you seldom see on universal motors.


But it's not the motor that is dying, it's the electronic speed
control.

If the motor is laboring too much and drawing too much current the switch
could overheat and fail. Probably better than the motor itself. Or the
switch design could be inferior.