I need some kind of device to strip the plastic coating off long lengths of
#14 insulated, solid, copper wire like you wire homes with . The wire was
salvaged from several dumpsters at homes under construction. Presently, I
am using an Exacto knife and just shaving off the insulation much like you
would peel a carrot and have managed to already draw blood. These cable
slitters advertised in catalogs seem to be about right but only for
....duh... cable... not what I'm trying to strip.

Larry

"Lawrence L'Hote" writes:

I need some kind of device to strip the plastic coating off long lengths
of
#14 insulated, solid, copper wire like you wire homes with . The wire was
salvaged from several dumpsters at homes under construction.

It's called a fire.

At least that is what one of my contractor customers did to salvage the
copper.

Bought his boat with the proceeds.

HTH

Lew

On Thu, 27 Jan 2005 22:39:26 GMT, Lew Hodgett wrote:

"Lawrence L'Hote" writes:

I need some kind of device to strip the plastic coating off long lengths
of
#14 insulated, solid, copper wire like you wire homes with . The wire was
salvaged from several dumpsters at homes under construction.

It's called a fire.

Yeah, that's a _great_ idea (rolls eyes).

At least that is what one of my contractor customers did to salvage the
copper.
Bought his boat with the proceeds.

Depends on how many miles of wires you're talking, but this would
be simple enough to rig something up for. Tubing, squeeze it down to
an oval, slit the tubing for a blade, and pull the wire through. No
muss, no fuss.

"Dave Hinz" wrote in message
...
On Thu, 27 Jan 2005 22:39:26 GMT, Lew Hodgett
wrote:

"Lawrence L'Hote" writes:

I need some kind of device to strip the plastic coating off long lengths
of
#14 insulated, solid, copper wire like you wire homes with . The wire
was
salvaged from several dumpsters at homes under construction.

It's called a fire.

Yeah, that's a _great_ idea (rolls eyes).

At least that is what one of my contractor customers did to salvage the
copper.
Bought his boat with the proceeds.

Depends on how many miles of wires you're talking, but this would
be simple enough to rig something up for. Tubing, squeeze it down to
an oval, slit the tubing for a blade, and pull the wire through. No
muss, no fuss.

Thanks, Dave, I thought of something like that but just thought I'd ask
around and see if someone had actually made/bought something. I have,
probably, about 20 lbs. of the stuff.

Larry

On Thu, 27 Jan 2005 22:51:39 GMT, Lawrence L'Hote wrote:

"Dave Hinz" wrote in message
...

Depends on how many miles of wires you're talking, but this would
be simple enough to rig something up for. Tubing, squeeze it down to
an oval, slit the tubing for a blade, and pull the wire through. No
muss, no fuss.

Thanks, Dave, I thought of something like that but just thought I'd ask
around and see if someone had actually made/bought something. I have,
probably, about 20 lbs. of the stuff.

Either way, you want to move the wire past the blade, not the other
way around. Safer and more predictable/adjustable. For only 20
pounds of wire, a little fiddling around as you go isn't the end
of the world.

Let us know what you end up doing. Also, rec.crafts.metalworking
might have some ideas. See you there, perhaps?

Dave Hinz

"Dave Hinz" wrote in message
...
On Thu, 27 Jan 2005 22:51:39 GMT, Lawrence L'Hote
wrote:

Let us know what you end up doing. Also, rec.crafts.metalworking
might have some ideas. See you there, perhaps?

Dave Hinz

Well I rigged something that works a WHOLE lot better than just wittlin' off
the insulation. I really appreciate all of you offering to hold my hand.
FWIW here is what I did. First I clamped a piece of L-shaped picture frame
on the work bench and cut a v-groove just so the insulation was above the
wood. You have to kind of round over the entrance end of the groove and
take all the kinks and bends out of the wire and stretch it across the room.
Strip back about 8" from the wire and position the stripped portion in the
groove. Press the flat of the cutter(Exacto knife) flat against the bare
wire at about a 30 deg horizontal angle with your right hand and pull the
wire through with your left. I could strip about a foot or more at a time.
I tried to clamp the blade down on the wire but that didn't work. I may
have already mentioned here a while back what I was doing with the wire
but here it is again... http://home.mchsi.com/~llhote/gallery/gallery.htm
Thanks again.
Larry

On Thu, 27 Jan 2005 22:19:12 GMT, "Lawrence L'Hote"
wrote:

I need some kind of device to strip the plastic coating off long lengths of
#14 insulated, solid, copper wire like you wire homes with . The wire was
salvaged from several dumpsters at homes under construction. Presently, I
am using an Exacto knife and just shaving off the insulation much like you
would peel a carrot and have managed to already draw blood. These cable
slitters advertised in catalogs seem to be about right but only for
...duh... cable... not what I'm trying to strip.

Will this do?

http://www.contacteast.com/product/g...arent_id=10592

"Guess who" wrote in message
...
On Thu, 27 Jan 2005 22:19:12 GMT, "Lawrence L'Hote"
wrote:

I need some kind of device to strip the plastic coating off long lengths
of
#14 insulated, solid, copper wire like you wire homes with . Will this
do?

http://www.contacteast.com/product/g...arent_id=10592


Thanks GW but I saw something like this when I looked around. The wire
w/insulation I have is 7/64 " but the lower limit on your suggestion is
5/32" I may have to go ahead and get the thing.
Larry

Lawrence L'Hote wrote:
"Guess who" wrote in message
...

On Thu, 27 Jan 2005 22:19:12 GMT, "Lawrence L'Hote"
wrote:


I need some kind of device to strip the plastic coating off long lengths
of
#14 insulated, solid, copper wire like you wire homes with . Will this
do?

http://www.contacteast.com/product/g...arent_id=10592



Thanks GW but I saw something like this when I looked around. The wire
w/insulation I have is 7/64 " but the lower limit on your suggestion is
5/32" I may have to go ahead and get the thing.
Larry


I made a nylon adapter (triangle block with a small v notch) for this
unit & screwed it to the top - works great on the smallest cables/wire
you'll ever find.