Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
There is a small pallet mill down on the other side of the railroad tracks
in town, and they appear to dump their scrap in a pile outside the fence. This morning I just happened to drop by and came away with quite a bit of oak, thicknesses 3/4 to maybe 8/4, 4 to 8 inches wide, and maybe two feet long. Dunno what I'll do with it yet, BUT: it's green. I'd like to retard checking as much as I can. I'm gonna store it in the basement, by the shop, stickered, but is there anything else I can do? I'm a little reluctant to dip the ends in wax (SWMBO has this unreasonable aversion to lumber in the kitchen - I can't figure it out...), but if that's what it takes, I'll figure out some way to do it. |
#2
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
* Jim Willemin wrote:
checking as much as I can. I'm gonna store it in the basement, by the shop, stickered, but is there anything else I can do? I'm a little reluctant to dip the ends in wax (SWMBO has this unreasonable aversion to lumber in the kitchen - I can't figure it out...), but if that's what it takes, I'll figure out some way to do it. I could totally be wrong about this but in the Bowyer's Bible series they just use elmers smeared over the endgrain. matthew ohio |
#3
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
If you don't do anything with it you will have firewood.
I have used roofing tar, others use paint. "Jim Willemin" wrote in message 7.131... There is a small pallet mill down on the other side of the railroad tracks in town, and they appear to dump their scrap in a pile outside the fence. This morning I just happened to drop by and came away with quite a bit of oak, thicknesses 3/4 to maybe 8/4, 4 to 8 inches wide, and maybe two feet long. Dunno what I'll do with it yet, BUT: it's green. I'd like to retard checking as much as I can. I'm gonna store it in the basement, by the shop, stickered, but is there anything else I can do? I'm a little reluctant to dip the ends in wax (SWMBO has this unreasonable aversion to lumber in the kitchen - I can't figure it out...), but if that's what it takes, I'll figure out some way to do it. |
#4
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
"Jim Willemin" wrote in message 7.131... There is a small pallet mill down on the other side of the railroad tracks in town, and they appear to dump their scrap in a pile outside the fence. This morning I just happened to drop by and came away with quite a bit of oak, thicknesses 3/4 to maybe 8/4, 4 to 8 inches wide, and maybe two feet long. Dunno what I'll do with it yet, BUT: it's green. I'd like to retard checking as much as I can. I'm gonna store it in the basement, by the shop, stickered, but is there anything else I can do? I'm a little reluctant to dip the ends in wax (SWMBO has this unreasonable aversion to lumber in the kitchen - I can't figure it out...), but if that's what it takes, I'll figure out some way to do it. If you have not used pallets before you may quickly realize that there are tons of nails and staples that break off in the wood. I worked for a company that received an average of 10-12 pallets a week and I finally came to the conclusion that it was best used for fire wood. |
#5
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
Sat, Sep 22, 2007, 10:09am (EDT-1)
(Jim*Willemin) doth sayeth: snip BUT: it's green. snip What are they teaching you guys in school nowadays? You're spelling is lousy. The correct spelling should be: BUT: it's free. JOAT What is life without challenge and a constant stream of new humiliations? - Peter Egan |
#6
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
"Toller" wrote in message
... If you don't do anything with it you will have firewood. I have used roofing tar, others use paint. What is the purpose of coating the ends, to prevent it taking on moisture? Dan |
#7
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
|
#8
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
"Leon" wrote in
: "Jim Willemin" wrote in message 7.131... There is a small pallet mill down on the other side of the railroad tracks in town, and they appear to dump their scrap in a pile outside the fence. This morning I just happened to drop by and came away with quite a bit of oak, thicknesses 3/4 to maybe 8/4, 4 to 8 inches wide, and maybe two feet long. Dunno what I'll do with it yet, BUT: it's green. I'd like to retard checking as much as I can. I'm gonna store it in the basement, by the shop, stickered, but is there anything else I can do? I'm a little reluctant to dip the ends in wax (SWMBO has this unreasonable aversion to lumber in the kitchen - I can't figure it out...), but if that's what it takes, I'll figure out some way to do it. If you have not used pallets before you may quickly realize that there are tons of nails and staples that break off in the wood. I worked for a company that received an average of 10-12 pallets a week and I finally came to the conclusion that it was best used for fire wood. I know that about actual pallets - this stuff is scrap from the mill that makes the pallets - rough cut hardwoods in little chunks, mostly. I have gotten maple, walnut, oak (mostly for practice turning). This haul was just a lot bigger and nicer than most, with stuff that I think will plane down nicely, if I can avoid checks. |
#9
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
"Dan" wrote in
: "Toller" wrote in message ... If you don't do anything with it you will have firewood. I have used roofing tar, others use paint. What is the purpose of coating the ends, to prevent it taking on moisture? As I understand it, it is to force slow even drying. The cut capillaries on end grain basically wick moisture out, and allow the stuff near the cut end to dry from the inside out, essentially, forcing the shrinking wood to split. If it dries from the sides instead of the ends, 1) it takes a lot longer, and 2) the wood shrinks from the outside in, allowing it to retain integrity. I just hope it'll be dry enough to work for Christmas... |
#10
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
"Jim Willemin" wrote in message 7.131... "Leon" wrote I know that about actual pallets - this stuff is scrap from the mill that makes the pallets - rough cut hardwoods in little chunks, mostly. I have gotten maple, walnut, oak (mostly for practice turning). This haul was just a lot bigger and nicer than most, with stuff that I think will plane down nicely, if I can avoid checks. Ah, rereading, I see you said scraps. That should be a cool stash. |
#11
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
|
#12
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
"Dan" wrote in message ... "Toller" wrote in message ... If you don't do anything with it you will have firewood. I have used roofing tar, others use paint. What is the purpose of coating the ends, to prevent it taking on moisture? If you don't coat them the ends will dry before the center. Since wood shrinks as it dries, the only way the ends can shrink when the center doesn't is by cracking. (makes sense if you think about it.) To make it dry evenly you coat the ends so it has to dry through the sides. |
#13
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
"Jim Willemin" wrote in message
As I understand it, it is to force slow even drying. The cut capillaries on end grain basically wick moisture out, and allow the stuff near the cut end to dry from the inside out, essentially, forcing the shrinking wood to split. If it dries from the sides instead of the ends, 1) it takes a lot longer, and 2) the wood shrinks from the outside in, allowing it to retain integrity. I just hope it'll be dry enough to work for Christmas... Makes sense. There's a place around the corner from me that usually has a huge pile of pallets marked "free". I've always assumed they were just low grade pine. Maybe I'll check 'em out. Dan |
#14
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
In article ews.net,
Puckdropper wrote: (J T) wrote in news:6615-46F5591A-1906 : Sat, Sep 22, 2007, 10:09am (EDT-1) (Jim*Willemin) doth sayeth: snip BUT: it's green. snip What are they teaching you guys in school nowadays? You're spelling is lousy. The correct spelling should be: BUT: it's free. JOAT What is life without challenge and a constant stream of new humiliations? - Peter Egan Free doesn't often mean "free." It means it didn't cost you anthing to acquire. Period. Use of the free item may cost you much more in the long run than spending money on a non-free item. Proof: there is nothing in this world that is more expensive than a woman who is free for the evening. |
#15
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
On Sat, 22 Sep 2007 16:03:29 -0700, "Dan" wrote:
"Jim Willemin" wrote in message As I understand it, it is to force slow even drying. The cut capillaries on end grain basically wick moisture out, and allow the stuff near the cut end to dry from the inside out, essentially, forcing the shrinking wood to split. If it dries from the sides instead of the ends, 1) it takes a lot longer, and 2) the wood shrinks from the outside in, allowing it to retain integrity. I just hope it'll be dry enough to work for Christmas... Makes sense. There's a place around the corner from me that usually has a huge pile of pallets marked "free". I've always assumed they were just low grade pine. Maybe I'll check 'em out. Dan I've found pallets Made from many different woods: Pine, Poplar, Oak, Basswood, Cottonwood (?) - I've even heard of Mahogany and other exotic woods from over seas and South America. It seems that pallets are made from whatever wood is available. A large pile of pallets can be a woodcarvers gold mine. Bill |
#16
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
|
#17
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
J T wrote:
Sun, Sep 23, 2007, 2:14pm (EDT+4) (Robert Bonomi) doth sayeth: Proof: there is nothing in this world that is more expensive than a woman who is free for the evening. Something like a $1,000 a night call girl, saying she is "free" for the evening, eh? A thousand buck a night call girl is a bargain--you don't end up wining and dining her for six months trying to get her to put out only to catch her in the sack with some bum. JOAT What is life without challenge and a constant stream of new humiliations? - Peter Egan -- -- --John to email, dial "usenet" and validate (was jclarke at eye bee em dot net) |
#18
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
|
#19
Posted to rec.woodworking
|
|||
|
|||
Minor newbie gloat
J T wrote:
Sun, Sep 23, 2007, 2:36pm (J. Clarke) A thousand buck a night call girl is a bargain--you don't end up wining and dining her for six months trying to get her to put out only to catch her in the sack with some bum. It would seem that you have a lot more disposable income than I do, and vastly different priorities on what to spend it on.. And, one HELL of a lot more patience. Nahh, both options are overpriced in my book. -- -- --John to email, dial "usenet" and validate (was jclarke at eye bee em dot net) |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Minor Gloat | Home Repair | |||
Minor gloat | Metalworking | |||
Minor gloat | Woodworking | |||
Minor gloat | Woodworking | |||
minor gloat | Woodworking |