Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Finishing Basement Shop Questions
Bill:
I have been framing my basement over the past couple of months and have concrete poured walls. I have left a 1/4 inch gap between the concrete and framing for moisture. If I read you posting correctly your walls are already insulated and you want to frame up against them. I would add a 6mil layer of plastic to the foil face and then frame up the walls leaving a 1/4" gap for airflow. Good luck !! wrote in message ... This may be a bit off topic, but it does relate to my new basement WW shop. First, some background. I have an unfinished basement in my new house. I have a 16.5' x 33' x 9' area set aside for my shop. Three of the walls are poured concrete foundation walls. The fourth wall is stud framed for about 80% and the remainder concrete foundation. The concrete foundation walls are covered horizontally with (2) 4' wide, foil faced, continuous wrap fiberglass insulation bats held to the wall using PAD* anchors. The stud wall I intend to cover with a smooth faced 1/2" plywood. This allows me to mount cabinets or shelves or clamp racks where ever I please. I don't really want to fully frame out the remaining walls. I'd like to maintain as much floor space as I can. My intention is to fur out the walls with 2x4's on the flat and then covering with my choice of plywood, paneling, or drywall. What I'm not sure about is how to handle the existing insulation. Should I: 1. Leave it, and place the furring strip 2x4's over it? or 2. Cut it wherever there will be a furring stri, then re-staple or tape it to the furring strip? or 3. Rip it down toss it out, and re-insulate using 1.5" foam board between my furring strips. The remaining walls and ceiling need to be finished (to minimize dust migration, provide smooth all mounting surfaces etc, and I'm undecided on how to go about this. Any suggestions? *Powder Actuated Device Bill Lewis REMOVE both "nospam-" in return address to reply. |
#2
|
|||
|
|||
Finishing Basement Shop Questions
Apparently I'm not being clear enough.
I don't want to frame out the walls. I don't want to lose floor space. I'd rather just fur out the wall with 2x4's laid flat against the existing wall, then use either plywood, drywall, paneling, or pegboard to cover. The question then becomes how to handle the situation with the existing insulation. This stuff wraps around the room horizontally with (2) 4' wide bats. So, do I 1. Leave it, and place the furring strip 2x4's over it? or 2. Cut it wherever there will be a furring strip, then re-staple or tape it to the furring strip? or 3. Rip it down toss it out, and re-insulate using 1.5" x 24" x 8' foam board between my furring strips. or 4. Open to suggestions??? On Sun, 14 Sep 2003 16:03:30 GMT, "RKON" wrote: I have been framing my basement over the past couple of months and have concrete poured walls. I have left a 1/4 inch gap between the concrete and framing for moisture. If I read you posting correctly your walls are already insulated and you want to frame up against them. I would add a 6mil layer of plastic to the foil face and then frame up the walls leaving a 1/4" gap for airflow. Good luck !! wrote in message .. . This may be a bit off topic, but it does relate to my new basement WW shop. First, some background. I have an unfinished basement in my new house. I have a 16.5' x 33' x 9' area set aside for my shop. Three of the walls are poured concrete foundation walls. The fourth wall is stud framed for about 80% and the remainder concrete foundation. The concrete foundation walls are covered horizontally with (2) 4' wide, foil faced, continuous wrap fiberglass insulation bats held to the wall using PAD* anchors. The stud wall I intend to cover with a smooth faced 1/2" plywood. This allows me to mount cabinets or shelves or clamp racks where ever I please. I don't really want to fully frame out the remaining walls. I'd like to maintain as much floor space as I can. My intention is to fur out the walls with 2x4's on the flat and then covering with my choice of plywood, paneling, or drywall. What I'm not sure about is how to handle the existing insulation. Should I: 1. Leave it, and place the furring strip 2x4's over it? or 2. Cut it wherever there will be a furring stri, then re-staple or tape it to the furring strip? or 3. Rip it down toss it out, and re-insulate using 1.5" foam board between my furring strips. The remaining walls and ceiling need to be finished (to minimize dust migration, provide smooth all mounting surfaces etc, and I'm undecided on how to go about this. Any suggestions? *Powder Actuated Device Bill Lewis REMOVE both "nospam-" in return address to reply. Bill Lewis REMOVE both "nospam-" in return address to reply. |
#3
|
|||
|
|||
Finishing Basement Shop Questions
wrote in message ... Apparently I'm not being clear enough. I don't want to frame out the walls. I don't want to lose floor space. I'd rather just fur out the wall with 2x4's laid flat against the existing wall, then use either plywood, drywall, paneling, or pegboard to cover. The question then becomes how to handle the situation with the existing insulation. This stuff wraps around the room horizontally with (2) 4' wide bats. So, do I 1. Leave it, and place the furring strip 2x4's over it? or 2. Cut it wherever there will be a furring strip, then re-staple or tape it to the furring strip? or 3. Rip it down toss it out, and re-insulate using 1.5" x 24" x 8' foam board between my furring strips. or 4. Open to suggestions??? I choose #3 because the wall will be more secure, better insulated, straighter, firmer. -- Is there no way that you can keep yourself from using this newsgroup as a place to vent on religion? Wrong place, wrong time. Jim in NC |
#4
|
|||
|
|||
Finishing Basement Shop Questions
"Morgans" wrote in message ... wrote in message ... Apparently I'm not being clear enough. I don't want to frame out the walls. I don't want to lose floor space. I'd rather just fur out the wall with 2x4's laid flat against the existing wall, then use either plywood, drywall, paneling, or pegboard to cover. The question then becomes how to handle the situation with the existing insulation. This stuff wraps around the room horizontally with (2) 4' wide bats. So, do I 1. Leave it, and place the furring strip 2x4's over it? or 2. Cut it wherever there will be a furring strip, then re-staple or tape it to the furring strip? or 3. Rip it down toss it out, and re-insulate using 1.5" x 24" x 8' foam board between my furring strips. or 4. Open to suggestions??? I choose #3 because the wall will be more secure, better insulated, straighter, firmer. -- Is there no way that you can keep yourself from using this newsgroup as a place to vent on religion? Wrong place, wrong time. Jim in NC Whoops1 Wrong sig line. Sorry! -- Jim in NC |
#5
|
|||
|
|||
Finishing Basement Shop Questions
Morgans wrote:
Is there no way that you can keep yourself from using this newsgroup as a place to vent on religion? Wrong place, wrong time. Whoops1 Wrong sig line. Sorry! I was wondering WTF you were talking about... -- Michael McIntyre ---- Silvan Linux fanatic, and certified Geek; registered Linux user #243621 Confirmed post number: 17831 Approximate word count: 534930 http://www.geocities.com/Paris/Rue/5407/ |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
can't pass up usefull trash | Metalworking | |||
Shop computer question | Metalworking | |||
Time for a dedicated shop | Woodworking | |||
Shop Power | Metalworking |