Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.woodworking
|
|||
|
|||
Taper jig??
I need to cut a "taper" on a piece of pine. It measures 3/4x1, about 4 ft.
long. I need to cut 3/16 at the top down to 1/16 at the bottom. Hope I'm explaining this right. Would the best thing to use be a taper jig or how? I have to do more of them, about 6 or 8. Never used a taper jig, so all advice and ideas are welcome. Tia Have a safe and prosperous New Year! |
#2
Posted to rec.woodworking
|
|||
|
|||
Taper jig??
http://www.woodworkingtips.com/etips/etip020607wb.html
Bob S. "Jimmy" wrote in message . net... I need to cut a "taper" on a piece of pine. It measures 3/4x1, about 4 ft. long. I need to cut 3/16 at the top down to 1/16 at the bottom. Hope I'm explaining this right. Would the best thing to use be a taper jig or how? I have to do more of them, about 6 or 8. Never used a taper jig, so all advice and ideas are welcome. Tia Have a safe and prosperous New Year! |
#3
Posted to rec.woodworking
|
|||
|
|||
Taper jig??
Jimmy wrote:
I need to cut a "taper" on a piece of pine. It measures 3/4x1, about 4 ft. long. I need to cut 3/16 at the top down to 1/16 at the bottom. Hope I'm explaining this right. Would the best thing to use be a taper jig or how? A taper sled works a lot better than a taper jig. -- It's turtles, all the way down |
#4
Posted to rec.woodworking
|
|||
|
|||
Taper jig??
Jimmy wrote:
I need to cut a "taper" on a piece of pine. It measures 3/4x1, about 4 ft. long. I need to cut 3/16 at the top down to 1/16 at the bottom. snip This is a natural for a scarfing jig, assuming you have either a router or a plane, either powered or hand. For this job, I would stay away from a table saw for safety reasons. Take a look at the home made scarfing jig shown in Fred Bingham's book, Practical Yacht Joinery. SFWIW, I have a 12:1 scarf jig made from 3/4 ply, hanging in my shed. Lew |
#5
Posted to rec.woodworking
|
|||
|
|||
Taper jig??
For this small of a taper you can use the trick normally used to fit
inset doors into an out of square hole. Just tack a 1/8" shim at one end of the board on the face that meets the fence. Since the piece is 4 ft long, create a fence extension that goes far enough back from the front of the blade, adjust the cut width and push it through. Jimmy wrote: I need to cut a "taper" on a piece of pine. It measures 3/4x1, about 4 ft. long. I need to cut 3/16 at the top down to 1/16 at the bottom. Hope I'm explaining this right. Would the best thing to use be a taper jig or how? I have to do more of them, about 6 or 8. Never used a taper jig, so all advice and ideas are welcome. Tia Have a safe and prosperous New Year! |
#6
Posted to rec.woodworking
|
|||
|
|||
Taper jig??
"Jimmy" wrote in message . net... I need to cut a "taper" on a piece of pine. It measures 3/4x1, about 4 ft. long. I need to cut 3/16 at the top down to 1/16 at the bottom. Hope I'm explaining this right. Would the best thing to use be a taper jig or how? I have to do more of them, about 6 or 8. Never used a taper jig, so all advice and ideas are welcome. Tia Have a safe and prosperous New Year! I would also use a sled rather than a jig. Using a sled was recommended to me, and I really like the results. Patt |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|