Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.woodworking
|
|||
|
|||
Adding space to a workshop
I'm adding a little space to the workshop. I have a question. When do you
install the window? I'm going to put in a small, cheap aluminum type storm window. So, I will put osb on the framing, then T-111. I'm not sure when the window goes in. Does it go on over the osb, or over the T-111? At least, I know it doesn't go on over the trim. Does it? G -- J.C. |
#2
Posted to rec.woodworking
|
|||
|
|||
Adding space to a workshop
I'm adding a little space to the workshop. I have a question. When do
you install the window? I'm going to put in a small, cheap aluminum type storm window. So, I will put osb on the framing, then T-111. I'm not sure when the window goes in. Does it go on over the osb, or over the T-111? At least, I know it doesn't go on over the trim. Does it? First, T-111 can serve as both structural sheathing and siding. No need to put OSB under it. Nail 1/2" or thicker T-111 directly to the studs, every 6" around the edges, and every 12" in the middle of the sheet. If you have 24" stud spacing, check the span ratings stamped on the plywood to see what thickness to use for your stud spacing (5/8" usually). As for the window, I run a bead of caulking around the window opening (under the windows flange), and nail the window to the outside of the plywood. I then caulk around the flange on the outside of the window and install my trim over the window flange. Finally, I caulk around the trim. I don't caulk the bottom side of the trim, just in case there is a small leak the water has a way to get out and not sit trapped behind the trim. I usually rabbet the back side of the window trim so it sits flat over the nails and flange of the window. As a last word, I'd go with a vinyl window instead of aluminum. Every aluminum window I have ever had sweats really bad, leading to rot and mold problems. Yuck... Anthony |
#3
Posted to rec.woodworking
|
|||
|
|||
Adding space to a workshop
"HerHusband" wrote in message ... I'm adding a little space to the workshop. I have a question. When do you install the window? I'm going to put in a small, cheap aluminum type storm window. So, I will put osb on the framing, then T-111. I'm not sure when the window goes in. Does it go on over the osb, or over the T-111? At least, I know it doesn't go on over the trim. Does it? First, T-111 can serve as both structural sheathing and siding. No need to put OSB under it. Nail 1/2" or thicker T-111 directly to the studs, every 6" around the edges, and every 12" in the middle of the sheet. If you have 24" stud spacing, check the span ratings stamped on the plywood to see what thickness to use for your stud spacing (5/8" usually). As for the window, I run a bead of caulking around the window opening (under the windows flange), and nail the window to the outside of the plywood. I then caulk around the flange on the outside of the window and install my trim over the window flange. Finally, I caulk around the trim. I don't caulk the bottom side of the trim, just in case there is a small leak the water has a way to get out and not sit trapped behind the trim. I usually rabbet the back side of the window trim so it sits flat over the nails and flange of the window. As a last word, I'd go with a vinyl window instead of aluminum. Every aluminum window I have ever had sweats really bad, leading to rot and mold problems. Yuck... Anthony Thanks for the helpful info. I'll take it all to heart. -- J.C. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
1st SMART HOME WORKSHOP and ICHIT 2006 | Home Repair | |||
Low height wardrobe/hanging space? | UK diy | |||
Space, stair & velux siteing regulations | UK diy | |||
crawl space - moisture problem | Home Repair | |||
No access to loft space. | UK diy |