So I'm about to put some hardwood floors (or laminate) in our laundry
room, which is shaped like a rectangle with part of the floor being
raised B in my sad ascii pic here

_________________
| | |
| A | B |
|___________| |
|_______________|


So my question is if I lay it horizontally (left to right on the pic) I
end up with a number of exposed short plank ends on the raised B bit,
how would I finish that edge. If I lay it vertically (up down on the
pic) I end up with a bunch of very short planks on the skinny bit of B
which I don't think would looks good, but I wouldn't get any exposed
end bits (that I don't know how to finish)

Thoughts ?

-- Damian

"damian penney" wrote in message =
oups.com...
| So I'm about to put some hardwood floors (or laminate) in our laundry
| room, which is shaped like a rectangle with part of the floor being
| raised B in my sad ascii pic here
|=20
| _________________
| | | |
| | A | B |
| |___________| |
| |_______________|
|=20
|=20
| So my question is if I lay it horizontally (left to right on the pic) =
I
| end up with a number of exposed short plank ends on the raised B bit,
| how would I finish that edge. If I lay it vertically (up down on the
| pic) I end up with a bunch of very short planks on the skinny bit of B
| which I don't think would looks good, but I wouldn't get any exposed
| end bits (that I don't know how to finish)
|=20
| Thoughts ?
|=20
| -- Damian
|=20

What is the height of the 'raise'?
What is the thickness of the 'laminate'?

I did my own floors with 3/4" hardwood laminate and cut my own risers. =
In one case I had to shave some off the back of one piece to get it to =
sit right.

If you mean that mm thick stuff, you might have to level the floor =
before installation.


--=20
PDQ

PDQ wrote:
"damian penney" wrote in message oups.com...
| So I'm about to put some hardwood floors (or laminate) in our laundry
| room, which is shaped like a rectangle with part of the floor being
| raised B in my sad ascii pic here
|
| _________________
| | | |
| | A | B |
| |___________| |
| |_______________|
|
|
| So my question is if I lay it horizontally (left to right on the pic) I
| end up with a number of exposed short plank ends on the raised B bit,
| how would I finish that edge. If I lay it vertically (up down on the
| pic) I end up with a bunch of very short planks on the skinny bit of B
| which I don't think would looks good, but I wouldn't get any exposed
| end bits (that I don't know how to finish)
|
| Thoughts ?
|
| -- Damian
|

What is the height of the 'raise'?
What is the thickness of the 'laminate'?

I did my own floors with 3/4" hardwood laminate and cut my own risers. In one case I had to shave some off the back of one piece to get it to sit right.

If you mean that mm thick stuff, you might have to level the floor before installation.


--
PDQ

The laminate would be the 8mm stuff (I haven't bought it yet) and the
raise is about 7" so it's a full step. I did see the trim pieces, and
in the Armstrong install guide it said for a flush stairnose I'd have
to route the ends of the pieces with their special bit (would a normal
t&g bit do the job though).

With regards my other question would you do this left right or up down
?

"damian penney" wrote in message =
oups.com...
|=20
|=20
| PDQ wrote:
| "damian penney" wrote in message =
oups.com...
| | So I'm about to put some hardwood floors (or laminate) in our =
laundry
| | room, which is shaped like a rectangle with part of the floor =
being
| | raised B in my sad ascii pic here
| |
| | _________________
| | | | |
| | | A | B |
| | |___________| |
| | |_______________|
| |
| |
| | So my question is if I lay it horizontally (left to right on the =
pic) I
| | end up with a number of exposed short plank ends on the raised B =
bit,
| | how would I finish that edge. If I lay it vertically (up down on =
the
| | pic) I end up with a bunch of very short planks on the skinny bit =
of B
| | which I don't think would looks good, but I wouldn't get any =
exposed
| | end bits (that I don't know how to finish)
| |
| | Thoughts ?
| |
| | -- Damian
| |
|
| What is the height of the 'raise'?
| What is the thickness of the 'laminate'?
|
| I did my own floors with 3/4" hardwood laminate and cut my own =
risers. In one case I had to shave some off the back of one piece to =
get it to sit right.
|
| If you mean that mm thick stuff, you might have to level the floor =
before installation.
|
|
| --
| PDQ
|=20
| The laminate would be the 8mm stuff (I haven't bought it yet) and the
| raise is about 7" so it's a full step. I did see the trim pieces, and
| in the Armstrong install guide it said for a flush stairnose I'd have
| to route the ends of the pieces with their special bit (would a normal
| t&g bit do the job though).
|=20
| With regards my other question would you do this left right or up down
| ?
|=20
Where one will find a 'round over' bit with an 8 mm arc is one of the =
mysteries of life.

If you want a proper edge, you better get the Armstrong bit.

As to the direction, do the rise vertical and lap the upper step over =
the rise just enough to cover the rise. No overhang as is done with the =
thicker stuff.


--=20
PDQ