I've got some blue lapus and malichite nugets (also some powdered copper
and brass).

I'm been wanting to experiment with crushed stone on my turnings. Not
having any pieces with some voids I can fill at this moment I was
thinking of cutting a notch into a nearly finished piece and the gluing
the stone or metal into the notch befor completing the turning.

I have a couple questions

1) How should I best get the stone or metal to stay in th notch that has
been cut all the way around the turning?

2) with the stone, how do you sand it smooth? I'm thinking of over
filling the notch with chushed stone and then using CA thin to glue it
in leaving some obove the surface of the turning that will then be
'sanded' smooth and flush. I'm also assuming that trying to cut the
stone with a chisel is a bad idea for the chisel and that it should be
sanded

"william kossack" wrote in message
news:4lg5d.259503$Fg5.238462@attbi_s53...
I've got some blue lapus and malichite nugets (also some powdered copper
and brass).

I'm been wanting to experiment with crushed stone on my turnings. Not
having any pieces with some voids I can fill at this moment I was
thinking of cutting a notch into a nearly finished piece and the gluing
the stone or metal into the notch befor completing the turning.

I have a couple questions

1) How should I best get the stone or metal to stay in the notch that has
been cut all the way around the turning?
=============================================
temporary fixing with masking tape will allow it to dry
========================================
2) with the stone, how do you sand it smooth? I'm thinking of over
filling the notch with chushed stone and then using CA thin to glue it
in leaving some obove the surface of the turning that will then be
'sanded' smooth and flush. I'm also assuming that trying to cut the
stone with a chisel is a bad idea for the chisel and that it should be
sanded
===============================
A good quality file will do a good job on softer stones and copper, brass,
aluminum, etc. Use it to flatten the over filled area to near the finished
level, then finish off with fine sandpaper on a craft stick (aka popsicle
stick). 3M sells diamond "files" that work well for harder stones. They are
available through jewelery supply places like Rio Grande, Fire Mountain,
etc.
If you try to sand all of it down, you'll probably also sand into the
adjacent wood area.
DON'T use a chisel unless it's one you don't like. {:-)

Ken Moon
Webberville, TX

A neighbor came over and we tried to crush a piece of the blue lapus

I had a piece of 3 inch galvanized pipe with an endcap and a section of
1 inch pipe with an end cape and could not break the lapus. This rig
works really well for the malichite. Any suggestions on how to crush
the stone?

Ken Moon wrote:
"william kossack" wrote in message
news:4lg5d.259503$Fg5.238462@attbi_s53...

I've got some blue lapus and malichite nugets (also some powdered copper
and brass).

I'm been wanting to experiment with crushed stone on my turnings. Not
having any pieces with some voids I can fill at this moment I was
thinking of cutting a notch into a nearly finished piece and the gluing
the stone or metal into the notch befor completing the turning.

I have a couple questions

1) How should I best get the stone or metal to stay in the notch that has
been cut all the way around the turning?

=============================================
temporary fixing with masking tape will allow it to dry
========================================

2) with the stone, how do you sand it smooth? I'm thinking of over
filling the notch with chushed stone and then using CA thin to glue it
in leaving some obove the surface of the turning that will then be
'sanded' smooth and flush. I'm also assuming that trying to cut the
stone with a chisel is a bad idea for the chisel and that it should be
sanded

===============================
A good quality file will do a good job on softer stones and copper, brass,
aluminum, etc. Use it to flatten the over filled area to near the finished
level, then finish off with fine sandpaper on a craft stick (aka popsicle
stick). 3M sells diamond "files" that work well for harder stones. They are
available through jewelery supply places like Rio Grande, Fire Mountain,
etc.
If you try to sand all of it down, you'll probably also sand into the
adjacent wood area.
DON'T use a chisel unless it's one you don't like. {:-)

Ken Moon
Webberville, TX