Home |
Search |
Today's Posts |
|
Woodturning (rec.crafts.woodturning) To discuss tools, techniques, styles, materials, shows and competitions, education and educational materials related to woodturning. All skill levels are welcome, from art turners to production turners, beginners to masters. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
How to make a tool rest?
I have aquired a craftsman 12" lathe that is very shiny and fixing to be
mounted to it's' new base. It was amde in 1974. The previous owner could not find the tool rest holder or tool rest for it. It has the bracket that is attached to the pipe. I am looking to make the tool rest and holder to save a few dollers since my layoff has left me short of spending cash. Can someone point me in the direction in need to go to find advice on this. I have googled myself to death and thougth someone here might have already made their own and could offer advice. Thanks Don Ft. Worth, TX |
#2
|
|||
|
|||
Greetings and Salutations...
On Thu, 28 Apr 2005 21:33:42 GMT, "BigDaddy" wrote: I have aquired a craftsman 12" lathe that is very shiny and fixing to be mounted to it's' new base. It was amde in 1974. The previous owner could not find the tool rest holder or tool rest for it. It has the bracket that is attached to the pipe. I am looking to make the tool rest and holder to save a few dollers since my layoff has left me short of spending cash. Can someone point me in the direction in need to go to find advice on this. I have googled myself to death and thougth someone here might have already made their own and could offer advice. Thanks Don Ft. Worth, TX A friend of mine had the same problem. I took a chunk of angle iron I had on hand, and, welded it to the top of a 7/8" hitch pin from Northern Tool. It needed a bit of work to get the top edge of the angle iron parallal to the turning axis, but, worked well enough. BVasically, all you need to do is measure the banjo hole and pick up a rod that fits...and get a crossbar of your choice welded to it. Regards Dave Mundt |
#3
|
|||
|
|||
A friend of mine had the same problem. I took a chunk of angle iron I had on hand, and, welded it to the top of a 7/8" hitch pin from Northern Tool. It needed a bit of work to get the top edge of the angle iron parallal to the turning axis, but, worked well enough. BVasically, all you need to do is measure the banjo hole and pick up a rod that fits...and get a crossbar of your choice welded to it. Regards Dave Mundt Thanks for the reply Dave. A question Does it matter if the top of the rest is flat, or can it be made from the same rod, welded into a "T"? Don Ft. Worth, TX |
#4
|
|||
|
|||
"BigDaddy" wrote in message news:1114888355.1845c6f598acdb0404565998f2f11eff@t eranews... SNIP ........ Thanks for the reply Dave. A question Does it matter if the top of the rest is flat, or can it be made from the same rod, welded into a "T"? Don Ft. Worth, TX ======================= You can use the same stock as the post, but on most machines, the post is near 1 in. Diameter, and that means your fulcrum cannot be placed very close to the work piece (at least 1/2 in from it). That isn't ideal. A piece of angle iron with the vertical portion nearest to the lathe will allow you to move up almost into contact with the work piece. The down side of this configuration is the possibility of running your tool past the end of the rest and having your finger slammmed down by the tool against the horizontal part of the angle iron. The cure for this is either filling the interior of the "L" with wood, epoxy, etc., or covering the open portion with sheet metal, etc. Make a careful measurement of your post. Many lathes use 1 inch posts, but their Asian counterparts use 25 mm posts. That's only 0.4mm difference, but it can be a problem. Good luck. Ken Moon Webbervile, TX. |
#5
|
|||
|
|||
Greetings and salutations...
On Sat, 30 Apr 2005 14:12:09 -0500, "BigDaddy" wrote: A friend of mine had the same problem. I took a chunk of angle iron I had on hand, and, welded it to the top of a 7/8" hitch pin from Northern Tool. It needed a bit of work to get the top edge of the angle iron parallal to the turning axis, but, worked well enough. BVasically, all you need to do is measure the banjo hole and pick up a rod that fits...and get a crossbar of your choice welded to it. Regards Dave Mundt Thanks for the reply Dave. A question Does it matter if the top of the rest is flat, or can it be made from the same rod, welded into a "T"? Don Ft. Worth, TX As a matter of fact, round rests like this seem to be the current fad in the turning world. There is a lot to be said for the bar type of rest, as it can make certain operations easier. I have yet to make one up to test the theory myself, although I have, at least, thought of it several times. Regards dave mundt |
#6
|
|||
|
|||
On Sat, 30 Apr 2005 14:12:09 -0500, "BigDaddy"
wrote: A friend of mine had the same problem. I took a chunk of angle iron I had on hand, and, welded it to the top of a 7/8" hitch pin from Northern Tool. It needed a bit of work to get the top edge of the angle iron parallal to the turning axis, but, worked well enough. BVasically, all you need to do is measure the banjo hole and pick up a rod that fits...and get a crossbar of your choice welded to it. Regards Dave Mundt Thanks for the reply Dave. A question Does it matter if the top of the rest is flat, or can it be made from the same rod, welded into a "T"? I made a couple of extra rests out of steel rod welded into a "T", and I actually like them quite a lot better than the cast iron ones that came with my lathe. Before welding, I ground the end of the rod that goes into the banjo slightly concave on the end of a belt sander to limit the gap I had to fill in, but the whole project only took about 5 mintues, and I made three of them. Don Ft. Worth, TX Aut inveniam viam aut faciam |
#7
|
|||
|
|||
I am going to try and weld up a couple today. I have a friend bringing his
welder over. Thanks for the ideas. Don "Prometheus" wrote in message news On Sat, 30 Apr 2005 14:12:09 -0500, "BigDaddy" wrote: A friend of mine had the same problem. I took a chunk of angle iron I had on hand, and, welded it to the top of a 7/8" hitch pin from Northern Tool. It needed a bit of work to get the top edge of the angle iron parallal to the turning axis, but, worked well enough. BVasically, all you need to do is measure the banjo hole and pick up a rod that fits...and get a crossbar of your choice welded to it. Regards Dave Mundt Thanks for the reply Dave. A question Does it matter if the top of the rest is flat, or can it be made from the same rod, welded into a "T"? I made a couple of extra rests out of steel rod welded into a "T", and I actually like them quite a lot better than the cast iron ones that came with my lathe. Before welding, I ground the end of the rod that goes into the banjo slightly concave on the end of a belt sander to limit the gap I had to fill in, but the whole project only took about 5 mintues, and I made three of them. Don Ft. Worth, TX Aut inveniam viam aut faciam |
#8
|
|||
|
|||
Hi Don
I'm not quite sure what you mean by toolrest and holder, I assume that "the bracket attached to the pipe" means the so called banjo and that you need what we call the toolrest, If that is the case I have made my toolrests myself and have pictures of them in one of my albums on the net. Have a look and see if that's what you need, they are very simple to make. Hope that's some help for you. Have fun and take care Leo Van Der Loo BigDaddy wrote: I have aquired a craftsman 12" lathe that is very shiny and fixing to be mounted to it's' new base. It was amde in 1974. The previous owner could not find the tool rest holder or tool rest for it. It has the bracket that is attached to the pipe. I am looking to make the tool rest and holder to save a few dollers since my layoff has left me short of spending cash. Can someone point me in the direction in need to go to find advice on this. I have googled myself to death and thougth someone here might have already made their own and could offer advice. Thanks Don Ft. Worth, TX |
#9
|
|||
|
|||
Sorry Don
forgot to include the album address, http://homepage.mac.com/l.vanderloo/PhotoAlbum25.html Hi Don I'm not quite sure what you mean by toolrest and holder, I assume that "the bracket attached to the pipe" means the so called banjo and that you need what we call the toolrest, If that is the case I have made my toolrests myself and have pictures of them in one of my albums on the net. Have a look and see if that's what you need, they are very simple to make. Hope that's some help for you. Have fun and take care Leo Van Der Loo BigDaddy wrote: I have aquired a craftsman 12" lathe that is very shiny and fixing to be mounted to it's' new base. It was amde in 1974. The previous owner could not find the tool rest holder or tool rest for it. It has the bracket that is attached to the pipe. I am looking to make the tool rest and holder to save a few dollers since my layoff has left me short of spending cash. Can someone point me in the direction in need to go to find advice on this. I have googled myself to death and thougth someone here might have already made their own and could offer advice. Thanks Don Ft. Worth, TX |
#11
|
|||
|
|||
Q: How do you make a tool rest? A: Take away the wood. :-) -- Sending unsolicited commercial e-mail to this account incurs a fee of $500 per message, and acknowledges the legality of this contract. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Robert Sorbey Modular tool rest does not fit Jet 1442 all that well | Woodturning | |||
FAST CASH SYSTEM !!! | Home Ownership | |||
South Bend 9" Lathe: Bowl Turning Tool Rest? | Woodturning | |||
HF 34706 lathe | Woodturning | |||
Bowl Saving: A Comprehensive Discussion | Woodturning |