I have a new cranked steel beam (inclined), which at one end fixes to the
existing wall of my house (like a lean-to) using a steel plate with two
holes to receive resin anchor fixings.

I'm guessing I need to drill two oversize holes in the brickwork, fill them
with some resin and then put some 12mm studding in and let it set, before
offering the steel up to it and screwing a nut on to hold it all in place.

Would someone be kind enough to confirm this or otherwise, and offer any
hard-learnt tips (including what type/form of resin I need, where I can get
it, setting times etc.)

Many thanks in advance.

p.s. I have a similar fixing at the lower end where another plate is fixed
to a pc concrete padstone using resin acnhors - I assume that the method
will be similar, but welcome comments to the contrary.

regards

KB



--
KEVIN BRADY, Oxford
_____________________
replies to newsgroup only
mail to reply address is automatically deleted from server

(including what type/form of resin I need, where I can get
it, setting times etc.)

http://www.toolstation.com/shop/Fixi...ngs/d90/sd1960
http://www.screwfix.com/app/sfd/cat/...00071&ts=50595

Christian.

Kevin Brady wrote:
I'm guessing I need to drill two oversize holes in the brickwork,
fill them
with some resin and then put some 12mm studding in and let it set,
before
offering the steel up to it and screwing a nut on to hold it all in
place.

I've just put some resin anchors in to hold a steel standard on one
side of a slap through. They're not taking much load so far as I can
see, I think they're just there to tie the wall end and standard
together - the standard was up and stable before I put the anchors in.

Anyway, I looked at the capsule systems, they seemed easiest, but in
the end, despite the low loads, plumped for this higher spec stuff I
got from screwfix as I was putting an order in there anyway:

http://www.screwfix.com/app/sfd/cat/...51021&ts=58157

I figured the stronger stuff might mitigate me making an arse of
installing it, well worth a couple of extra quid. I got studs and bolts
from SF as well.

For 8mm studs it required a 10mm hole. I think the 2mm offset is
constant as the stud sizes go up. I drilled in place and through bolted
so had to add an extra 0.5mm on to the hole in the standard to get the
masonary bit in clean. After drilling I took a good few minutes per
hole cleaning it out with a small bottle brush and a bic biro tube
attached to foot pump as a blower. Blow and brush at least twice.

The applicator works by twisting the end so I did a trial run to see
how many turns were required to extrude enough gunge to fill a hole,
then put that plus a little bit more in each hole. You want to discrd
the first few inches of gunge anyway to ensure a good mix. Quick as
possible, put the studs in with a bit of screw action then leave well
alone. The gunge is thick enough to hold the stids exactly where you
want them and level. The cure time was estimated as two hours for the
temperature (indoors). I left it a day. No faith, me.

Overall, I was pretty impressed with them. Very easy to do.

Thanks both of you guys - I was wondering whether to go for resin capsule or
injection method - I too like a bit of belt & braces to make up for any
shortcomings in experience/skill.

Will post if I have any hilarious anecdotes (like roof caving in when
tiled).


--
KEVIN BRADY, Oxford
_____________________
replies to newsgroup only
mail to reply address is automatically deleted from server
"urchaidh" wrote in message
ups.com...
Kevin Brady wrote:
I'm guessing I need to drill two oversize holes in the brickwork,
fill them
with some resin and then put some 12mm studding in and let it set,
before
offering the steel up to it and screwing a nut on to hold it all in
place.

I've just put some resin anchors in to hold a steel standard on one
side of a slap through. They're not taking much load so far as I can
see, I think they're just there to tie the wall end and standard
together - the standard was up and stable before I put the anchors in.

Anyway, I looked at the capsule systems, they seemed easiest, but in
the end, despite the low loads, plumped for this higher spec stuff I
got from screwfix as I was putting an order in there anyway:

http://www.screwfix.com/app/sfd/cat/...51021&ts=58157

I figured the stronger stuff might mitigate me making an arse of
installing it, well worth a couple of extra quid. I got studs and bolts
from SF as well.

For 8mm studs it required a 10mm hole. I think the 2mm offset is
constant as the stud sizes go up. I drilled in place and through bolted
so had to add an extra 0.5mm on to the hole in the standard to get the
masonary bit in clean. After drilling I took a good few minutes per
hole cleaning it out with a small bottle brush and a bic biro tube
attached to foot pump as a blower. Blow and brush at least twice.

The applicator works by twisting the end so I did a trial run to see
how many turns were required to extrude enough gunge to fill a hole,
then put that plus a little bit more in each hole. You want to discrd
the first few inches of gunge anyway to ensure a good mix. Quick as
possible, put the studs in with a bit of screw action then leave well
alone. The gunge is thick enough to hold the stids exactly where you
want them and level. The cure time was estimated as two hours for the
temperature (indoors). I left it a day. No faith, me.

Overall, I was pretty impressed with them. Very easy to do.