"Huge" wrote in message
...
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

--
"The road to Paradise is through Intercourse."
[email me at huge [at] huge [dot] org [dot] uk]



Magnetic door catches. Try www.mvmlocks.com/IH_catches_ives.html for some
idea of what I mean

On 1 Jan 2005 13:43:39 GMT, (Huge) wrote:

Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...



How about magnetism.

Axminster, and I'm sure others, sell rare earth magnets quite cheaply
- http://www.axminster.co.uk/product.a...sfile=1&jump=0

Construct a wooden frame and fix that in place to the floor, walls
etc. to give a firm foundation. Drill holes for the magnets with a
Forstner bit or spade bit with care and glue in the magnets.

Take some penny washers (say 25mm diameter with a small hole) -
available from usual sources - roughen and epoxy them to the inside of
the panel.

It meets all of your criteria.....

I've used this quite successfully for a panel of similar size to a
bath one. It is as well to arrange a small gap somewhere to slide a
hook in for later removal. These are quite strong magnets......



--

..andy

To email, substitute .nospam with .gl

On 1 Jan 2005 13:43:39 GMT, (Huge) wrote:

Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the
outside), adjustable (it's bound not to be level) and removable
(should I need to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it
on with nice screws (chromed dome heads or mirror screws or
somesuch)...



How about magnetism.


Magnetism's good..
But in my rental property's I use few dabs of silicone, oafs have failed to
knock then off but with a bit of gentle leverage it can be removed.

Huge wrote:

Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

magnets?

SNAP!!!

"Stephen Dawson" wrote in message
...
SNAP!!!

Snap fasteners are surprisingly good at holding wooden members. We have a
folding table, salvaged from dead father in law's house, which uses them to
hold legs together. I was dubious about the strength at first but they work
very well. The table is used when camping for the 'kitchen', it is used for
food preparation as well as bearing the cooker, 5 gallon water container
etc.

Mary

In an earlier contribution to this discussion,
Huge wrote:

Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the
outside), adjustable (it's bound not to be level) and removable
(should I need to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

My side panel is fixed on *virtually* invisibly.

The top of the panel is rebated to go behind the turned-over lip of the
bath. The bottom is about 3cm off the floor. Attached to the floor, just
inboard of the panel, is a plinth made of a strip of white Conti-board,
about 8cm high. There are a couple of those little plastic connecting blocks
screwed to the bottom edge of the panel and, in turn, screwed into the
plinth. Invisible? - well, you have virtually to lie on the floor to see
them - particularly since they're white against a white background.
--
Cheers,
Set Square
______
Please reply to newsgroup. Reply address is invalid.

"Huge" wrote
| Anyone got any good ideas on how to fasten a wooden side panel
| onto a bath in such a way that the fastening is; invisible (from
| the outside), adjustable (it's bound not to be level) and removable
| (should I need to get at my scabby plumbing)?

Velcro.

Owain

On Sat, 1 Jan 2005 14:36:54 -0000, "Owain"
wrote:

"Huge" wrote
| Anyone got any good ideas on how to fasten a wooden side panel
| onto a bath in such a way that the fastening is; invisible (from
| the outside), adjustable (it's bound not to be level) and removable
| (should I need to get at my scabby plumbing)?

Velcro.


At work we use some sort of "Industrial" Velcro which uses interlocking
plastic bobbles rather than the fibrous textile stuff to hold cosmetic
panels onto our machines.

DG

"Huge" wrote in message
...
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

--
"The road to Paradise is through Intercourse."
[email me at huge [at] huge [dot] org [dot] uk]


=================
Use a short length of broom handle with either:

http://www.screwfix.com/app/sfd/cat/pro.jsp?ts=93504&id=16457
or
http://www.screwfix.com/app/sfd/cat/cat.jsp?ts=93606&id=100031


Cic.

Huge wrote:

I'd already discounted magnetic door catches, since they are designed to take loads
normal to the magnet, not axially, and this thing weighs several kilos.

Don't under-estimate the power of rare earth magnets, maybe I still hate
velcro because of it's noise.

"Andy Burns" wrote in message
...
Huge wrote:

I'd already discounted magnetic door catches, since they are designed to
take loads
normal to the magnet, not axially, and this thing weighs several kilos.

Then install a couple of stands that the panel can stand on, this will
remove the vertical (axially) forces and the a couple of magnets will do
just fine...


Don't under-estimate the power of rare earth magnets, maybe I still hate
velcro because of it's noise.

Rare earth magnets (Neodynium) are VERY strong so should easily cope with
the panel alone without the stands described above...


/Morten



---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.825 / Virus Database: 563 - Release Date: 30/12/2004

In article , "Huge"
says...
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

Magnets?

In article , "Huge"
says...
(Steve Firth) writes:
Huge wrote:

Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

Velcro, just to give an alternative to magnets. You can buy in in
stick-on lengths at most DIY places and since I don't trust the stick
on, I would bang a few staples through it as well.

Bingo!

I'd already discounted magnetic door catches, since they are designed to take loads
normal to the magnet, not axially, and this thing weighs several kilos.

So fix some adjustable feet on the back to hold it level.

On 1 Jan 2005 15:00:18 GMT, (Huge) wrote:

(Steve Firth) writes:
Huge wrote:

Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

Velcro, just to give an alternative to magnets. You can buy in in
stick-on lengths at most DIY places and since I don't trust the stick
on, I would bang a few staples through it as well.

Bingo!

I'd already discounted magnetic door catches, since they are designed to take loads
normal to the magnet, not axially, and this thing weighs several kilos.


Isn't it going to sit on the floor or other support at the bottom?

BTW. I found with the rare earth magnets that there was no sliding
anyway. THey're pretty powerful....



--

..andy

To email, substitute .nospam with .gl

Huge wrote:
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

I've just found a couple of rolls of Scotch "Magnatherm" tape in a box
in the loft (Ideal weather for turning out the loft!) It is in two
parts, one is a self adheasive steel band , the other is a magnetic
band. Sold for DIY double glazing in 1/2" wide, 10' lengths.

Should do you!

Andrew

"Huge" wrote in message
...
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

--
"The road to Paradise is through Intercourse."
[email me at huge [at] huge [dot] org [dot] uk]


Try these http://www.toolstation.com/search.html?searchstr=42384

work a treat for me


Dave Jones

"Huge" wrote in message
...
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

--
"The road to Paradise is through Intercourse."
[email me at huge [at] huge [dot] org [dot] uk]

How about NO NAILS, it seems to work for most stuff. But what happens if
you get a leaky pipe & need to take the panel off at some stage?

Jo

"Jo" wrote in message
...

"Huge" wrote in message
...
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

--
"The road to Paradise is through Intercourse."
[email me at huge [at] huge [dot] org [dot] uk]

How about NO NAILS, it seems to work for most stuff. But what happens
if
you get a leaky pipe & need to take the panel off at some stage?


I fitted mine (having constructed it) so that the top of the panel was
rammed up under the lip of the bath. The panel was then fixed with brass
screws and cup washers at the bottom edge only to blocks I had previously
fixed to the floor. I then sealed the top edge wth clear silicone mastic.
The only visible fixings are therefore along the bottom edge and almost
invisible.


--
Bob Mannix
(anti-spam is as easy as 1-2-3 - not)

2 x 2 wood screwed to the floor, and self-adhesive velcro strips fixed to
this and the bath side panel. Works a treat. You won't need too much
velcro or you won't be able to get it off - I use about 3 x 3 inches in
total for the long bit.

All the best, Colin
"Bob Mannix" wrote in message
...

"Jo" wrote in message
...

"Huge" wrote in message
...
Anyone got any good ideas on how to fasten a wooden side panel onto a
bath in such a way that the fastening is; invisible (from the outside),
adjustable (it's bound not to be level) and removable (should I need
to get at my scabby plumbing)?

I'm tempted to ignore the "invisible" requirement and just screw it on
with nice screws (chromed dome heads or mirror screws or somesuch)...

--
"The road to Paradise is through Intercourse."
[email me at huge [at] huge [dot] org [dot] uk]

How about NO NAILS, it seems to work for most stuff. But what happens
if
you get a leaky pipe & need to take the panel off at some stage?


I fitted mine (having constructed it) so that the top of the panel was
rammed up under the lip of the bath. The panel was then fixed with brass
screws and cup washers at the bottom edge only to blocks I had previously
fixed to the floor. I then sealed the top edge wth clear silicone mastic.
The only visible fixings are therefore along the bottom edge and almost
invisible.


--
Bob Mannix
(anti-spam is as easy as 1-2-3 - not)