Hi All,

So my wife is designing our bedroom and wants a pelmet covering the top of the curtains. It is basically flat but then she wants an ornate top and then the whole lot painted. To keep the weight of the whole thing down (it is about 2.4m long) I was thinking of getting 6mm ply/ MDF for the front, sides and top and then use some say 1"x1" battens in the corners to screw the ply to and essentially make a bottomless/ backless box then fix the ornate beading to it. Looking online, looks like all the ones I could fine use 18mm MDF and just screw them together (e.g. the front board screwed directly into the edge of the sides).

TBH the other technique seems a lot easier/ quicker but wanted to solicit feedback here. Maybe there is a better approach?

thanks

Lee.

On 08/09/2019 14:53, Lee Nowell wrote:
Hi All,

So my wife is designing our bedroom and wants a pelmet covering the top of the curtains. It is basically flat but then she wants an ornate top and then the whole lot painted. To keep the weight of the whole thing down (it is about 2.4m long) I was thinking of getting 6mm ply/ MDF for the front, sides and top and then use some say 1"x1" battens in the corners to screw the ply to and essentially make a bottomless/ backless box then fix the ornate beading to it. Looking online, looks like all the ones I could fine use 18mm MDF and just screw them together (e.g. the front board screwed directly into the edge of the sides).

TBH the other technique seems a lot easier/ quicker but wanted to solicit feedback here. Maybe there is a better approach?

thanks

Lee.

I'd agree with you. In the "old days" pelmet front/tops were often
hardboard.

Yes ours was and inside of the top and front had some dampening polystyrene
on ours, probably not got for elf and safety these days.
Brian

--
----- --
This newsgroup posting comes to you directly from...
The Sofa of Brian Gaff...

Blind user, so no pictures please
Note this Signature is meaningless.!
"newshound" wrote in message
...
On 08/09/2019 14:53, Lee Nowell wrote:
Hi All,

So my wife is designing our bedroom and wants a pelmet covering the top
of the curtains. It is basically flat but then she wants an ornate top
and then the whole lot painted. To keep the weight of the whole thing
down (it is about 2.4m long) I was thinking of getting 6mm ply/ MDF for
the front, sides and top and then use some say 1"x1" battens in the
corners to screw the ply to and essentially make a bottomless/ backless
box then fix the ornate beading to it. Looking online, looks like all
the ones I could fine use 18mm MDF and just screw them together (e.g. the
front board screwed directly into the edge of the sides).

TBH the other technique seems a lot easier/ quicker but wanted to solicit
feedback here. Maybe there is a better approach?

thanks

Lee.

I'd agree with you. In the "old days" pelmet front/tops were often
hardboard.

On Sunday, 8 September 2019 14:53:53 UTC+1, Lee Nowell wrote:
Hi All,

So my wife is designing our bedroom and wants a pelmet covering the top of the curtains. It is basically flat but then she wants an ornate top and then the whole lot painted. To keep the weight of the whole thing down (it is about 2.4m long) I was thinking of getting 6mm ply/ MDF for the front, sides and top and then use some say 1"x1" battens in the corners to screw the ply to and essentially make a bottomless/ backless box then fix the ornate beading to it. Looking online, looks like all the ones I could fine use 18mm MDF and just screw them together (e.g. the front board screwed directly into the edge of the sides).

TBH the other technique seems a lot easier/ quicker but wanted to solicit feedback here. Maybe there is a better approach?

thanks

Lee.

18mm won't go anywhere. 6mm should be alright but no guarantees long term, it's thin & can go out of whack. Hardboard of course has even worse rigidity - it isn't. ISTR one pelmet bing supported by the rail using clips that miss the curtain mechanism.


NT

On 08/09/2019 19:33, wrote:
On Sunday, 8 September 2019 14:53:53 UTC+1, Lee Nowell wrote:
Hi All,

So my wife is designing our bedroom and wants a pelmet covering the top of the curtains. It is basically flat but then she wants an ornate top and then the whole lot painted. To keep the weight of the whole thing down (it is about 2.4m long) I was thinking of getting 6mm ply/ MDF for the front, sides and top and then use some say 1"x1" battens in the corners to screw the ply to and essentially make a bottomless/ backless box then fix the ornate beading to it. Looking online, looks like all the ones I could fine use 18mm MDF and just screw them together (e.g. the front board screwed directly into the edge of the sides).

TBH the other technique seems a lot easier/ quicker but wanted to solicit feedback here. Maybe there is a better approach?

thanks

Lee.

18mm won't go anywhere. 6mm should be alright but no guarantees long term, it's thin & can go out of whack. Hardboard of course has even worse rigidity - it isn't. ISTR one pelmet bing supported by the rail using clips that miss the curtain mechanism.


NT

They used to use hardboard with vertical "ripples" about an inch wide. I
guess that makes it a bit thicker and hence stiffer.

On Sunday, 8 September 2019 22:26:57 UTC+1, newshound wrote:
On 08/09/2019 19:33, tabbypurr wrote:

18mm won't go anywhere. 6mm should be alright but no guarantees long term, it's thin & can go out of whack. Hardboard of course has even worse rigidity - it isn't. ISTR one pelmet bing supported by the rail using clips that miss the curtain mechanism.


NT

They used to use hardboard with vertical "ripples" about an inch wide. I
guess that makes it a bit thicker and hence stiffer.

I'd quite forgotten that. Hideous stuff IIRC.


NT

On 08/09/2019 23:44, wrote:
On Sunday, 8 September 2019 22:26:57 UTC+1, newshound wrote:
On 08/09/2019 19:33, tabbypurr wrote:

18mm won't go anywhere. 6mm should be alright but no guarantees long term, it's thin & can go out of whack. Hardboard of course has even worse rigidity - it isn't. ISTR one pelmet bing supported by the rail using clips that miss the curtain mechanism.


NT

They used to use hardboard with vertical "ripples" about an inch wide. I
guess that makes it a bit thicker and hence stiffer.

I'd quite forgotten that. Hideous stuff IIRC.

Yes, we had pelmets like that. I used to attach Meccano pulleys there
and to furniture and run cable-cars up and down.

SteveW

Thanks all. With regard to hanging the curtains I was planning on screwing the rail to the wall rather than hung off the pelmet.

How do you hang the curtains. Also would not a top make it less draughty?
Brian

--
----- --
This newsgroup posting comes to you directly from...
The Sofa of Brian Gaff...

Blind user, so no pictures please
Note this Signature is meaningless.!
"Lee Nowell" wrote in message
...
Hi All,

So my wife is designing our bedroom and wants a pelmet covering the top of
the curtains. It is basically flat but then she wants an ornate top and
then the whole lot painted. To keep the weight of the whole thing down (it
is about 2.4m long) I was thinking of getting 6mm ply/ MDF for the front,
sides and top and then use some say 1"x1" battens in the corners to screw
the ply to and essentially make a bottomless/ backless box then fix the
ornate beading to it. Looking online, looks like all the ones I could fine
use 18mm MDF and just screw them together (e.g. the front board screwed
directly into the edge of the sides).

TBH the other technique seems a lot easier/ quicker but wanted to solicit
feedback here. Maybe there is a better approach?

thanks

Lee.

On 08/09/2019 14:53, Lee Nowell wrote:

So my wife is designing our bedroom and wants a pelmet covering the top of the curtains. It is basically flat but then she wants an ornate top and then the whole lot painted.

Cut a couple of end pieces from 18mm MDF or 3/4 inch pine plank.

Cut a 1"x1" notch out of the front top corner of each end and join them
with a suitable length of 1x1. Pin & glue 6mm MDF to make the front and top.