it is not an electric one - It sits on the stove and is heated by
direct contact ..So it has a very thick and flat base.It is stainless
steel and has sprung a leak where the spout joins the body.
Now I imagine that the spout was welded to the body in the
manufacturing and the leak seems to be along the seam of the join...
Now I suppose I could get it rewelded but I have no such skills or
acquaintances with those skills so it may have to be done another way.
If I put chemical metal along the seam this would need to be done
externally as the seem inside the kettle is inacessible owing to a tea
strainer like covering (you know like what you see in a tea pot to
prevent the worst of the tea leaves being pored out)
So if I am going to block up the seam on the outside I am going to
have to do it quite well (since it is stanless steel the surface is
very smooth so I might have to roughen it)

So has anyone a better idea than to put a line of chemical metal along
the seam on the outside?
As the leak only really starts when the kettle is almost half full I
have a feeling that the pressure may not be really strong and so maybe
a careful job will fix it without the need for welding or dismantling
(but I would like to use something a little better than chemical metal
if that was possible)

meuharris wrote:
it is not an electric one - It sits on the stove and is heated by
direct contact ..So it has a very thick and flat base.It is stainless
steel and has sprung a leak where the spout joins the body.
Now I imagine that the spout was welded to the body in the
manufacturing and the leak seems to be along the seam of the join...
Now I suppose I could get it rewelded but I have no such skills or
acquaintances with those skills so it may have to be done another way.
If I put chemical metal along the seam this would need to be done
externally as the seem inside the kettle is inacessible owing to a tea
strainer like covering (you know like what you see in a tea pot to
prevent the worst of the tea leaves being pored out)
So if I am going to block up the seam on the outside I am going to
have to do it quite well (since it is stanless steel the surface is
very smooth so I might have to roughen it)

So has anyone a better idea than to put a line of chemical metal along
the seam on the outside?
As the leak only really starts when the kettle is almost half full I
have a feeling that the pressure may not be really strong and so maybe
a careful job will fix it without the need for welding or dismantling
(but I would like to use something a little better than chemical metal
if that was possible)
Clean the area with descaling fluid and then use slow setting araldite
epoxy allow to harden in a warm not hot place( otherwise it runs).
Roughening the surface will help the bond.

Bob

On 22 Aug, 20:02, Bob Minchin wrote:
meuharris wrote:
it is not an electric one - It sits on the stove and is heated by
direct contact ..So it has a very thick and flat base.It is stainless
steel and has sprung a leak where the spout joins the body.
Now I imagine that the spout was welded to the body in the
manufacturing and the leak seems to be along the seam of the join...
Now I suppose I could get it rewelded but I have no such skills or
acquaintances with those skills so it may have to be done another way.
If I put chemical metal along the seam this would need to be done
externally as the seem inside the kettle is inacessible owing to a tea
strainer like covering (you know like what you see in a tea pot to
prevent the worst of the tea leaves being pored out)
So if I am going to block up the seam on the outside I am going to
have to do it quite well (since it is stanless steel the surface is
very smooth so I might have to roughen it)

So has anyone a better idea than to put a line of chemical metal along
the seam on the outside?
As the leak only really starts when the kettle is almost half full I
have a feeling that the pressure may not be really strong and so maybe
a careful job will fix it without the need for welding or dismantling
(but I would like to use something a little better than chemical metal
if that was possible)

Clean the area with descaling fluid and then use slow setting araldite
epoxy allow to harden in a warm not hot place( otherwise it runs).
Roughening the surface will help the bond.

Bob- Hide quoted text -

- Show quoted text -

thanks.Actually are you sure about the descaling fluid? As it is
stainless steel and I hope to be appllying whatever it is on the
outside I don't imagine there would be any hard water deposits at all
(we have peaty soil here anyway so I think the water must be super
soft)
I will take your advice about the slow setting araldite though as it
seems like it would be a lot neater than chemical metal along a
narrow seam..

"meuharris" wrote in message
...
it is not an electric one - It sits on the stove and is heated by
direct contact ..So it has a very thick and flat base.It is stainless
steel and has sprung a leak where the spout joins the body.
Now I imagine that the spout was welded to the body in the
manufacturing and the leak seems to be along the seam of the join...
Now I suppose I could get it rewelded but I have no such skills or
acquaintances with those skills so it may have to be done another way.
If I put chemical metal along the seam this would need to be done
externally as the seem inside the kettle is inacessible owing to a tea
strainer like covering (you know like what you see in a tea pot to
prevent the worst of the tea leaves being pored out)
So if I am going to block up the seam on the outside I am going to
have to do it quite well (since it is stanless steel the surface is
very smooth so I might have to roughen it)

So has anyone a better idea than to put a line of chemical metal along
the seam on the outside?
As the leak only really starts when the kettle is almost half full I
have a feeling that the pressure may not be really strong and so maybe
a careful job will fix it without the need for welding or dismantling
(but I would like to use something a little better than chemical metal
if that was possible)

http://www.repairproducts.co.uk/page41.htm

On 23 Aug, 10:03, "R" wrote:
"meuharris" wrote in message

...





it is not an electric one - It sits on the stove and is heated by
direct contact ..So it has a very thick and flat base.It is stainless
steel and has sprung a leak where the spout joins the body.
Now I imagine that the spout was welded to the body in the
manufacturing and the leak seems to be along the seam of the join...
Now I suppose I could get it rewelded but I have no such skills or
acquaintances with those skills so it may have to be done another way.
If I put chemical metal along the seam this would need to be done
externally as the seem inside the kettle is inacessible owing to a tea
strainer like covering (you know like what you see in a tea pot to
prevent the worst of the tea leaves being pored out)
So if I am going to block up the seam on the outside I am going to
have to do it quite well (since it is stanless steel the surface is
very smooth so I might have to roughen it)

So has anyone a better idea than to put a line of chemical metal along
the seam on the outside?
As the leak only really starts when the kettle is almost half full I
have a feeling that the pressure may not be really strong and so maybe
a careful job will fix it without the need for welding or dismantling
(but I would like to use something a little better than chemical metal
if that was possible)

http://www.repairproducts.co.uk/page41.htm- Hide quoted text -

- Show quoted text -

thanks I will have a look at them