Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to uk.d-i-y
|
|||
|
|||
one for the electrical engineers
I recently acquired a workshop dust extractor. In bits because the waste
had clogged the fan and burned out the motor capacitor (single phase 2.2kW) I have no means of checking for shorted turns but the winding resistance values look OK (1.6 and 4.0 Ohms ) and it does not appear to fault to the frame. Very much a dead parrot moment except there is no means of guessing the original rating. ISTR a thread on this subject and will look when I have more time. However, it occurred to me that someone might have a similar unit and could look up the values for me. Alternatively given that this is a large diameter steel! fan is it possible to determine the rating by any other means? regards -- Tim Lamb |
#2
Posted to uk.d-i-y
|
|||
|
|||
one for the electrical engineers
In article ,
Tim Lamb writes: I recently acquired a workshop dust extractor. In bits because the waste had clogged the fan and burned out the motor capacitor (single phase 2.2kW) I have no means of checking for shorted turns but the winding resistance values look OK (1.6 and 4.0 Ohms ) and it does not appear to fault to the frame. I doubt that caused the capacitor to burn out. It was probably going to burn out anyway. Very much a dead parrot moment except there is no means of guessing the original rating. Normally doesn't matter very much -- mainly affects the starting torque, and a fan probably doesn't have much initial resistance. ISTR a thread on this subject and will look when I have more time. However, it occurred to me that someone might have a similar unit and could look up the values for me. Alternatively given that this is a large diameter steel! fan is it possible to determine the rating by any other means? Is it not written on the rating plate? What is written on the rating plate? -- Andrew Gabriel [email address is not usable -- followup in the newsgroup] |
#3
Posted to uk.d-i-y
|
|||
|
|||
one for the electrical engineers
In message , Andrew Gabriel
writes In article , Tim Lamb writes: I recently acquired a workshop dust extractor. In bits because the waste had clogged the fan and burned out the motor capacitor (single phase 2.2kW) I have no means of checking for shorted turns but the winding resistance values look OK (1.6 and 4.0 Ohms ) and it does not appear to fault to the frame. I doubt that caused the capacitor to burn out. It was probably going to burn out anyway. Very much a dead parrot moment except there is no means of guessing the original rating. Normally doesn't matter very much -- mainly affects the starting torque, and a fan probably doesn't have much initial resistance. No but there is a lot of inertia in such a heavy fan. Is it not written on the rating plate? What is written on the rating plate? Power 2200W phase 1 Volt 230V HZ 50 Amp 9.6A Class B RPM 2950 SER All fairly self explicit except *SER*. I tried spinning the motor with string wound round the shaft (might have the direction wrong) and could not hear any centrifugal switch clicks. There are no access plates and I don't want to draw the end covers off unnecessarily. Perhaps the first move is to borrow a capacitor from another motor and try livening it up on no load. If the supply trips out I can show it to my local rewind firm and then decide. regards -- Tim Lamb |
#4
Posted to uk.d-i-y
|
|||
|
|||
one for the electrical engineers
Tim Lamb wrote:
Is it not written on the rating plate? What is written on the rating plate? Power 2200W phase 1 Volt 230V HZ 50 Amp 9.6A Class B RPM 2950 SER All fairly self explicit except *SER*. snip I would think this is short for serial number - probably worn off by now or stamped but not deep enough to read. -- Spamtrap in use To email replace 127.0.0.1 with btinternet dot com |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Resources for Engineers | Metalworking | |||
Porter-Cable 8501 question for electrical engineers / technicians / electricians only | Woodworking | |||
Okay all you mechanical engineers ... | Woodworking | |||
Doomed Engineers | Metalworking | |||
Understanding Engineers | Metalworking |