Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to uk.d-i-y
|
|||
|
|||
Requirements for switches to 'fixed' equipment
Further to my recent question about garage door openers....
If I wire them permanently - i.e. remove the plug and connect direct to the mains wiring - I believe the wiring regulations require some means of disconnecting the equipment. Is this correct? I think it has to be double pole and also at least 2mm separation or something. Will a standard switched FCU fulfil the requirement? How close does the switch have to be to the equipment? Can I use one switch for two adjacent garage door openers, they're about 8ft apart. -- Chris Green |
#2
Posted to uk.d-i-y
|
|||
|
|||
Requirements for switches to 'fixed' equipment
In article ,
wrote: Further to my recent question about garage door openers.... If I wire them permanently - i.e. remove the plug and connect direct to the mains wiring - I believe the wiring regulations require some means of disconnecting the equipment. Is this correct? I think it has to be double pole and also at least 2mm separation or something. Will a standard switched FCU fulfil the requirement? Yes. How close does the switch have to be to the equipment? Can I use one switch for two adjacent garage door openers, they're about 8ft apart. I'd fit one per door, and make them accessible. -- *i souport publik edekashun. Dave Plowman London SW To e-mail, change noise into sound. |
#3
Posted to uk.d-i-y
|
|||
|
|||
Requirements for switches to 'fixed' equipment
"Dave Plowman (News)" wrote:
In article , wrote: Further to my recent question about garage door openers.... If I wire them permanently - i.e. remove the plug and connect direct to the mains wiring - I believe the wiring regulations require some means of disconnecting the equipment. Is this correct? I think it has to be double pole and also at least 2mm separation or something. Will a standard switched FCU fulfil the requirement? Yes. Thanks! How close does the switch have to be to the equipment? Can I use one switch for two adjacent garage door openers, they're about 8ft apart. I'd fit one per door, and make them accessible. I guess they only cost a couple of quid so three rather than two is hardly going to break the bank! :-) They'll be accessible as in adjacent to the door opener which in one case can be reached from the floor but in the other two cases is out of reach (except for my 6'6" son) unless you're on a ladder. -- Chris Green |
#4
Posted to uk.d-i-y
|
|||
|
|||
Requirements for switches to 'fixed' equipment
If I wire them permanently - i.e. remove the plug and connect direct
to the mains wiring - I believe the wiring regulations require some means of disconnecting the equipment. Is this correct? Yes. I think it has to be double pole and also at least 2mm separation or something. 3mm. Will a standard switched FCU fulfil the requirement? Yes. How close does the switch have to be to the equipment? Can I use one switch for two adjacent garage door openers, they're about 8ft apart. The switch must be close enough to be considered to be in control of someone servicing the equipment. i.e. close enough so that they can see it and scream at the muppet about to electrocute them. Alternatively, the switch should be lockable in the off position. It doesn't have to be close for emergency stop reasons unless the equipment itself is worthy of such a device. Christian. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
FS: TEST EQUIPMENT (etc) - Tektronix, HP, others | Electronics | |||
10 years ARM mortgage rate higher then 30 year fixed? | Home Ownership | |||
Question about 110v equipment | UK diy | |||
Ground to Gas Pipe?? | Home Repair |