How do the experts mount newer taps to older basins, which have oversized
square holes?

The large rubber washer which is used to create a watertight seal between
the base of the tap and the ceramic washbasin, tends to distort and/or
become displaced after a while of turning the tap on and off. This
eventually permits water which has been splashed onto the surrounding area
to leak down through the mounting hole and onto the floor below creating a
damp patch. No amount of tightening of the (plastic!) nut on the underside
will prevent this happening, so I was wondering if there is some sort of
sealant that would effect a satisfactory cure?

Thanks for reading.

Nigel

On Fri, 30 Dec 2005 13:57:55 GMT, "nrh" wrote:

How do the experts mount newer taps to older basins, which have oversized
square holes?

The large rubber washer which is used to create a watertight seal between
the base of the tap and the ceramic washbasin, tends to distort and/or
become displaced after a while of turning the tap on and off. This
eventually permits water which has been splashed onto the surrounding area
to leak down through the mounting hole and onto the floor below creating a
damp patch. No amount of tightening of the (plastic!) nut on the underside
will prevent this happening, so I was wondering if there is some sort of
sealant that would effect a satisfactory cure?

Thanks for reading.

Nigel


Hi,

You may want a tap centralising washer:

http://www.google.com/search?hs=Kmh&hl=en&lr=&safe=off&client=opera&rls= en&q=tap+centralising+washer&btnG=Search

or make one out of thick plastic (small chopping board etc).

To get the best seal on a washer, use a jointing compound like Fernox
LSX or similar:

http://www.google.com/search?hs=37M&hl=en&lr=&safe=off&client=opera&rls= en&q=fernox+lsx&btnG=Search

I usually put a thickish layer on, wait til it _starts_ to 'set up' ie
goes rubbery instead of sticky, fit the parts and tighten a little.

Then give it longer say 30 mins to set more and tighten fully. Some of
it gets squashed out but can be cleaned off fairly easily after it's
set.

cheers,
Pete.

In ,
Pete C scribed:
On Fri, 30 Dec 2005 13:57:55 GMT, "nrh" wrote:

How do the experts mount newer taps to older basins, which have oversized
square holes?

The large rubber washer which is used to create a watertight seal between
the base of the tap and the ceramic washbasin, tends to distort and/or
become displaced after a while of turning the tap on and off. This
eventually permits water which has been splashed onto the surrounding
area to leak down through the mounting hole and onto the floor below
creating a damp patch. No amount of tightening of the (plastic!) nut on
the underside will prevent this happening, so I was wondering if there
is some sort of sealant that would effect a satisfactory cure?

Thanks for reading.

Nigel


Hi,

You may want a tap centralising washer:

http://www.google.com/search?hs=Kmh&hl=en&lr=&safe=off&client=opera&rls= en&q=tap+centralising+washer&btnG=Search

or make one out of thick plastic (small chopping board etc).

To get the best seal on a washer, use a jointing compound like Fernox
LSX or similar:

http://www.google.com/search?hs=37M&hl=en&lr=&safe=off&client=opera&rls= en&q=fernox+lsx&btnG=Search

I usually put a thickish layer on, wait til it _starts_ to 'set up' ie
goes rubbery instead of sticky, fit the parts and tighten a little.

Then give it longer say 30 mins to set more and tighten fully. Some of
it gets squashed out but can be cleaned off fairly easily after it's
set.

cheers,
Pete.

Pete your a star! I just happen to have some Fernox LSX in my bag too! :-)
Now where's that flippin' chopping board? ;-)

Many thanks indeed for the info, and a happy New Year to you and yours.

Nigel