UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions.

 
 
LinkBack Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
  #1   Report Post  
Hugo Nebula
 
Posts: n/a
Default Leaking heat exchanger on a new boiler

Long tale of woe...

My mother's 14-month old boiler sprung a leak yesterday. The water
that came out was completely black. After finding a plumber out of
the Yellow Pages (Tesco Insurance's 24-hour emergency hotline, my
arse!), he said the leak is coming from the cast-iron heat exchanger.
He expressed surprise that the heat exchanger should spring a leak in
such a short period of time, and that, if the system had been flushed
properly, the water should be so black.

The boiler, an Ideal Classic FF340, was fitted as a replacement to an
original system. This was supposedly power-flushed by the installers,
but according to yesterday's plumber, this should have taken about 4
hours, whereas my mother reckons it was a lot less than that (mind
you, she is in her eighties and does get confused, so she's not a
reliable witness).

Further information that may or may not be relevant:
i) All the radiators are fitted with TRVs, I think there is a by-pass,
but it doesn't have any kind of flow valve on it. I fitted a room
thermostat as there wasn't one before, and told my mother to keep the
TRV in the same room fully open (replacing the TRV with a lockshield
valve would have required a round tuit, which wasn't available at the
time). My sister visited last week and turned the valve down.
ii) Since the boiler was installed, it's only been used full for about
three-four months. My mother went into hospital in early January, and
was there for six months. While she was away, apart from a couple of
weekends I stayed over, the thermostat was lowered to keep it ticking
over on frost protection. Last weekend was the first time it's been
used apart from hot water for 9 months.

Questions:
1. Can an unflushed system cause a cast-iron heat exchanger to leak
after 14 months (unless there's a manufacturing fault)?
2. If there isn't a by-pass circuit, could all the valves being up to
temperature have caused enough pressure to rupture the heat exchanger?
3. Would a long layoff or low level of usage have exacerbated this
problem?
4. Who's at fault here? The boiler's manufacturer's, or the
installers (name-and-shame time: Merseyside Central Heating of
Crosby)?
--
Hugo Nebula
"If no-one on the internet wants a piece of this,
just how far from the pack have you strayed?"
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
New condensing boiler installation - truth or lies Martin Evans UK diy 57 July 2nd 05 02:13 PM
Condensing Boiler News RedOnRed UK diy 0 April 9th 05 05:37 PM
Boiler problem: flushing a dual tube heat exchanger [email protected] UK diy 4 January 2nd 05 08:28 AM
11degC across Boiler, why? Tom UK diy 54 September 24th 04 07:32 AM
Heat banks (again!) Dave UK diy 148 September 6th 04 08:45 PM


All times are GMT +1. The time now is 10:51 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"