Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Propane blow lamps or torches
I've used three butane blowlamps, mainly for pipework, over the years
(the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? -- Kevin Poole **Use current month and year to reply (e.g. )*** Car Transport by Tiltbed Trailer - based near Derby |
#2
|
|||
|
|||
"Autolycus" wrote in message ... I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? I've used the Calor version for a number of years and have nozzles that allow me to do anything from small part soldering to paint stripping outdoors in a wind. I find the type with canisters to be a very pale imitation. Colin Bignell |
#3
|
|||
|
|||
Autolycus wrote:
I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? How much is a bottle of gas for these? |
#4
|
|||
|
|||
On Tue, 23 Aug 2005 13:14:24 GMT, "ben" wrote:
Autolycus wrote: I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? How much is a bottle of gas for these? You can use the small Calor gas cylinders. A 4kg cylinder refill costs about £10, so considerably cheaper than the little cartridges. -- ..andy To email, substitute .nospam with .gl |
#5
|
|||
|
|||
Andy Hall wrote:
On Tue, 23 Aug 2005 13:14:24 GMT, "ben" wrote: Autolycus wrote: I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? How much is a bottle of gas for these? You can use the small Calor gas cylinders. A 4kg cylinder refill costs about £10, so considerably cheaper than the little cartridges. How long do you reckon one of them would last paint stripping, give or take 10 minutes or a wild guess? |
#6
|
|||
|
|||
On Tue, 23 Aug 2005 19:58:10 GMT, "ben" wrote:
Andy Hall wrote: On Tue, 23 Aug 2005 13:14:24 GMT, "ben" wrote: Autolycus wrote: I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? How much is a bottle of gas for these? You can use the small Calor gas cylinders. A 4kg cylinder refill costs about £10, so considerably cheaper than the little cartridges. How long do you reckon one of them would last paint stripping, give or take 10 minutes or a wild guess? Have a look at http://www.sievert.se/en/pro86_88.htm The consumption is very dependent on the burner, but the paint stripping ones seem to be rated at around 200g/hr. -- ..andy To email, substitute .nospam with .gl |
#7
|
|||
|
|||
Andy Hall wrote:
The consumption is very dependent on the burner, but the paint stripping ones seem to be rated at around 200g/hr. So if my maths stand up, a 4kg cylinder would run for 20 hours? Wow! For a £10? Wow again - that is really cheap. I may well buy one! Dave |
#8
|
|||
|
|||
On Tue, 23 Aug 2005 13:14:24 GMT, "ben" wrote:
How much is a bottle of gas for these? £2.50+VAT Go to your local dump and buy one. If you hunt around, you can usually find some that are half-full. I buy all my propane this way and get enough to run a gas forge, and to keep me in scrap empty cylinders for making woodstoves. |
#9
|
|||
|
|||
On Tue, 23 Aug 2005 13:37:28 +0100, "Autolycus"
wrote: I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? I have a similar thing made by Primus-Sievert that I bought about 25 years ago. I have small and large burners for it for plumbing and a fan shaped one for paint stripping. Works really well. -- ..andy To email, substitute .nospam with .gl |
#10
|
|||
|
|||
A few years ago I found myself in the same situation having had several
blowlamps, none of which I'd been happy with. In the end I bought a Primus-Sievert with piezo-electric ignition (MachineMart and Toolbank sell them). It's much better than any of the others I've used and I'm entiurely happy with it. Not had any problems with flaring either. Well worth the money. |
#11
|
|||
|
|||
In message , Autolycus
writes I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. Anyone tried one of these? Any good? Any similar recommendations? I have the Calor equivalent that I bought about 8 years ago and it is 1000 times easier and safer to use than the canister style blow lamps. No faring and fits into smaller spaces. -- Bill |
#12
|
|||
|
|||
I've used three butane blowlamps, mainly for pipework, over the years (the sort that use disposable canisters) and all of them have been prone to flaring when you tilt them too far before they're fully warmed up. I see that Machine Mart do a "proper" torch (Clarke FCSF109) http://www.machinemart.co.uk/product...7&r=2037&g=105 for £23. In connection with this subject my son uses a Rothenberger piezo igniton torch with the MAPP gas cylinder The torch is about £60 and new cylinder about £12 in England. He has been on holiday in Florida where he saw the torches at $30 and cylinders in Walmart at $3. -- .. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Degassing propane tanks (for Grant) | Metalworking | |||
propane compressed air torches | UK diy | |||
heat pump/secondary propane furnace questions | Home Ownership | |||
preparing a propane tank for reusal .. pix | Metalworking | |||
Propane for heat? | Home Repair |