I am planning to run a extension from an existing TV aerial socket (type
that is on a plate flush to the wall). Without taking this off the wall
to look at the back (new house... not moved in yet), is this easy to do
? Are there likely to be terminals on the back of the plate that I can
wire a series entension into ? Or do I have to remove the existing wire,
fit a plug, then into a splitted then one to the current socket via a
short cable and a new cable to the new one, allowing the splitter to
drop into the wall behind ?

NC wrote:
I am planning to run a extension from an existing TV aerial socket
(type that is on a plate flush to the wall). Without taking this off
the wall to look at the back (new house... not moved in yet), is this
easy to do ? Are there likely to be terminals on the back of the
plate that I can wire a series entension into ? Or do I have to
remove the existing wire, fit a plug, then into a splitted then one
to the current socket via a short cable and a new cable to the new
one, allowing the splitter to drop into the wall behind ?

There are terminals on the back of the ariel plate but you will find ariel
cable might come through the wall from the outside another aspect is the
cable might come from the loft and recessed in the wall(chasing)then
plastered over.

So to use an extension from the socket you would have to chase the wall that
has the socket, down to the floor.

Easiest way IMHO is to have another ariel put on the mast and the cable run
to the back of the house or where ever your going to sight the other TV.
Using two TV's on the same ariel reduces the signal level a bit.

In article , ben
wrote:


There are terminals on the back of the ariel plate but you will find ariel
cable

I know thay they make soap powder, but I was unaware that you can buy Ariel
cable.

So to use an extension from the socket you would have to chase the wall that
has the socket, down to the floor.

No. You don't treat it like a ring main. There are impedances and suchlike
to bear in mind.

Easiest way IMHO is to have another ariel put on the mast and the cable run
to the back of the house

Very messy and unprofessional, besides being daft.

or where ever your going to sight the other TV.
Using two TV's on the same ariel reduces the signal level a bit.

Not by anything you need to be concerned about. Otherwise the main aerial
system needs sorting out first.

The correct solution to feed just one additional TV, is to install a
waterproof, inductive splitter in the cable run from the mast and then feed
directly to where required.

It could also be done by plugging in an inductive splitter to the existing
socket and running the second point from there. A further option is to split
it off at the output of the connected VCR / SAY / Freeview receiver.

--
AJL Electronics (G6FGO) Ltd : Satellite and TV aerial systems
http://www.classicmicrocars.co.uk : http://www.ajlelectronics.co.uk

On Mon, 18 Jul 2005 09:41:57 UTC, "Andy Luckman (AJL Electronics)"
wrote:

In article , ben
wrote:


There are terminals on the back of the ariel plate but you will find ariel
cable

I know thay they make soap powder, but I was unaware that you can buy Ariel
cable.

No, I think he's off with the fairies!

NC wrote:

I am planning to run a extension from an existing TV aerial socket (type
that is on a plate flush to the wall). Without taking this off the wall
to look at the back (new house... not moved in yet), is this easy to do
? Are there likely to be terminals on the back of the plate that I can
wire a series entension into ? Or do I have to remove the existing wire,
fit a plug, then into a splitted then one to the current socket via a
short cable and a new cable to the new one, allowing the splitter to
drop into the wall behind ?

First of all, do youy want to run a separate TV? Or just 'move' the socket?

If the latter, just solder new cable on* and use a blanking plate on the
existing...

IF OTOH you want to run several TV's you need a proper splitter. This
will degrade signal a bit and if you want half a dozen TV's you really
need a booster splitter - preferably up near the aerial...

* This is not totally trivial - exetnding co-ax cable: If you don't know
how to do it ask again.

If youu are adding a second TV, you sound like you're adding a second cable
to the back of this socket.

I'm assuming this is your main TV point which might have any of the
following: VCR, Sky, Cable.

Consider changing the face plate for a double one.
Come out of one of these as you do now, go through your equipment and before
you get to the TV, split it.
Then one goes to the TV, one to the second wall socket.

This way, the other TV will be able to get Sky/VCR aswell.

Just an idea, it's what i've done.