Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
PHOTOS was Anyone needs a $87,000+ military NavAir thingamabob?
The little units are 24V relays. Keep the relays and their sockets. Pitch
the rest. RellikJM "Ignoramus3395" wrote in message ... On 21 Mar 2005 03:53:51 GMT, Ignoramus28076 wrote: I have a power supply for some military surface to air unit that originally cost $87,000. As far as I could tell, it is worthless and cannot be sold on ebay. It has a lot of specialty connectors. This thing is about 25 lbs or less and is not that big. It has a lot of little similar semiconductor units inside, which, as far as I could tell, are also worthless. Photos: http://igor.chudov.com/tmp/Navair-Power-Supply/ i |
#2
|
|||
|
|||
Ignoramus14288 wrote:
On Mon, 21 Mar 2005 23:33:46 -0700, RellikJM GO@SPAM wrote: The little units are 24V relays. Keep the relays and their sockets. Pitch the rest. Is there any way to find out what the relays do? Where are the "coil" contacts and where are the NO or NC contacts? Err, the label on the top of the relay cases tells you which are the coil pins and which are NO, NC. If pins are 1 2 3 4 5 X 7 8 9 A X C D E F G Then coil is 3 & E 7 is NC to 5 & NO to 1 1 is NC to 4 & No to 8 and so on. Caveat, I'm not wearing my glasses. |
#3
|
|||
|
|||
"Ignoramus14288" skrev i en meddelelse ... On Mon, 21 Mar 2005 23:33:46 -0700, RellikJM GO@SPAM wrote: The little units are 24V relays. Keep the relays and their sockets. Pitch the rest. Is there any way to find out what the relays do? Where are the "coil" contacts and where are the NO or NC contacts? http://igor.chudov.com/tmp/Navair-Po...y/dscf0095.jpg Coil is X1 + X2 the relay in the pic has 4 sets of contacts.. A1 is NO A3 is NC A2 is the other end of A1 or A3 Same thing with B, C and D sets.. Coil specs: 26.5VDC, 150 ohms.. It will probably run fine on 24VDC /peter |
#4
|
|||
|
|||
In article ,
RellikJM GO@SPAM SOMEONE ELSE.COM wrote: The little units are 24V relays. Keep the relays and their sockets. Pitch the rest. Agreed -- except also be sure to keep the hardware which mounts the sockets and accepts the screws from the relays, too. Those are top-quality relays, and usable even in space (since they have a sealed environment, so they won't have a problem with vacuum welding of the contacts. The two large boxes near the rear are the only power supplies in there, and it looks as though they depend on the chassis for heat-sinking, based on the smear of heat-sink grease (the white stuff) around the base of one. Enjoy, DoN. -- Email: | Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Photos of radial arm saw flipper stops (repost with corrected link) | Woodworking | |||
OT Guns more Guns | Metalworking | |||
I would like to see photos of your versions of.... | Woodworking |