On Wed, 01 Sep 2004 03:04:21 GMT, Gunner
wrote:

On Tue, 31 Aug 2004 15:59:08 -0400, "BW"
wrote:

I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W

Two sheets of 3/4" plywood. Lay the far one under the one the mill is
on. Push to the new sheet, remove the old one, pry up the far end,
stick the new sheet under the one the mill is on, move to this sheet
and repeat. Takes more time to explain than to do.

Gunner

If I can't come up with three sheets I look to zenith.

The plywood prices are terrible . I use to get large counter tops from
dumpster diving. Their particle board , but 3/4 and laminated on the
other side. After 911 everyone seemed to stop making major screw ups.
I'm sure NAFTA didn't help.

Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

james, Port Orchard (seattle), Washington, USA, Earth


On Wed, 01 Sep 2004 20:09:26 -0700, Sunworshipper
wrote:

On Wed, 01 Sep 2004 03:04:21 GMT, Gunner
wrote:

On Tue, 31 Aug 2004 15:59:08 -0400, "BW"
wrote:

I finally got moved into my new house and the machines are nestled into the
garage. I have to move the lathe and bridgeport into the cellar. I have a
walk-in door to the basement but the problem is getting the stuff to the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was quite
a job. I am leery of trying to move the base the same way. Any suggestions
on moving the base ? There is not enough room to get a large machine in to
carry it.

Thanks,

Bill W

Two sheets of 3/4" plywood. Lay the far one under the one the mill is
on. Push to the new sheet, remove the old one, pry up the far end,
stick the new sheet under the one the mill is on, move to this sheet
and repeat. Takes more time to explain than to do.

Gunner

If I can't come up with three sheets I look to zenith.

The plywood prices are terrible . I use to get large counter tops from
dumpster diving. Their particle board , but 3/4 and laminated on the
other side. After 911 everyone seemed to stop making major screw ups.
I'm sure NAFTA didn't help.

On Thu, 02 Sep 2004 04:51:40 -0700, RainLover
wrote:

Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Is that Can't (as in 'NO, and that's FINAL!'), or Can't (as in 'You
don't have the proper straps, rigging and spreader bars yet, you might
scratch the paint Honey Dear...')?

If it was the second answer, does she have a single sister? ;-P

-- Bruce --
--
Bruce L. Bergman, Woodland Hills (Los Angeles) CA - Desktop
Electrician for Westend Electric - CA726700
5737 Kanan Rd. #359, Agoura CA 91301 (818) 889-9545
Spamtrapped address: Remove the python and the invalid, and use a net.

Sorry, I am in Massachusetts.

The plywood sounds good. I've got the base on a new skid that I built and
I'll get the plywood today and give it a go.

Thanks,

BW
"RainLover" wrote in message
...
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

james, Port Orchard (seattle), Washington, USA, Earth


On Wed, 01 Sep 2004 20:09:26 -0700, Sunworshipper
wrote:

On Wed, 01 Sep 2004 03:04:21 GMT, Gunner
wrote:

On Tue, 31 Aug 2004 15:59:08 -0400, "BW"
wrote:

I finally got moved into my new house and the machines are nestled into
the
garage. I have to move the lathe and bridgeport into the cellar. I have
a
walk-in door to the basement but the problem is getting the stuff to
the
door. There is about 40' of grass to move the stuff over. I moved the
bridgeport head and table on a skid by using rollers under it. It was
quite
a job. I am leery of trying to move the base the same way. Any
suggestions
on moving the base ? There is not enough room to get a large machine in
to
carry it.

Thanks,

Bill W

Two sheets of 3/4" plywood. Lay the far one under the one the mill is
on. Push to the new sheet, remove the old one, pry up the far end,
stick the new sheet under the one the mill is on, move to this sheet
and repeat. Takes more time to explain than to do.

Gunner

If I can't come up with three sheets I look to zenith.

The plywood prices are terrible . I use to get large counter tops from
dumpster diving. Their particle board , but 3/4 and laminated on the
other side. After 911 everyone seemed to stop making major screw ups.
I'm sure NAFTA didn't help.

RainLover wrote:
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Come on over to Issaquah! I'm moving in about a month and I've got a
lathe that prolly weighs more than your wife's car that needs to be
stuffed into a truck or something..

Oh, and here's the secret phrase you must learn in dealing with your
wife on these matters: "Hey, what can go wrong?!"

Sometimes, this is followed shortly thereafter with another magical,
secret phrase: "Hey, who knew?!" ;-)
--
Doug
http://www.des.indianchief.com/index.htm

On Thu, 02 Sep 2004 16:13:15 GMT, Doug Smith
wrote:

RainLover wrote:
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Come on over to Issaquah! I'm moving in about a month and I've got a
lathe that prolly weighs more than your wife's car that needs to be
stuffed into a truck or something..

Oh, and here's the secret phrase you must learn in dealing with your
wife on these matters: "Hey, what can go wrong?!"

Sometimes, this is followed shortly thereafter with another magical,
secret phrase: "Hey, who knew?!" ;-)


"hey, hold my beer and watch this!"

Gunner

"In my humble opinion, the petty carping levied against Bush by
the Democrats proves again, it is better to have your eye plucked
out by an eagle than to be nibbled to death by ducks." - Norman
Liebmann

Gunner wrote:

"hey, hold my beer and watch this!"

NO! Never give up yer beer! Nothing good can come of this. I once
fell down an entire flight of stairs without spilling a drop. Got a
standing ovation from an admiring crowd for that one..

Of course, I was considerably younger then. Now, I'd probably get all
banged up and stuff. Still wouldn't spill any beer tho..

They can take my beer when they can peel my cold dead fingers from
around the can. ;-)
--
Doug
http://www.des.indianchief.com/index.htm

On Thu, 02 Sep 2004 16:13:15 GMT, Doug Smith
wrote:

RainLover wrote:
Where are you located? I've got this new knuckle-boom I'm itchin' to
try out and my wife says I can't lift her car up with it!

Come on over to Issaquah! I'm moving in about a month and I've got a
lathe that prolly weighs more than your wife's car that needs to be
stuffed into a truck or something..

Oh, and here's the secret phrase you must learn in dealing with your
wife on these matters: "Hey, what can go wrong?!"

Sometimes, this is followed shortly thereafter with another magical,
secret phrase: "Hey, who knew?!" ;-)

Don't tell me, you Consider the Red Green show to be a Religion? LOL

I'd move it, but you'd have to pay for gas and ferry to get me there
and back! What's your guess on its weight?

James, Port Orchard.

RainLover wrote:
...snippage...
Don't tell me, you Consider the Red Green show to be a Religion? LOL

Heh.. I have seen that show a few times and it has always made me laugh
out loud.


...snippage...
I'd move it, but you'd have to pay for gas and ferry to get me there
and back! What's your guess on its weight?

Oh, I'd gladly pay more than that. I'm looking at a 24' truck with lift
gate -- gotta see how much that lift gate can lift. If not enough (and
I expect it won't be) I might just take you up on that!

Weight is 3,000 lbs for the lathe. The other tools are all sub-1000
pounders and, hence, no problem even for the lift gate thang.

Jeez, I kinda dread this move. What an ordeal. But the end result will
be worth it..
--
Doug
http://www.des.indianchief.com/index.htm

On Fri, 03 Sep 2004 06:29:27 GMT, Doug Smith
wrote:

RainLover wrote:
...snippage...
Don't tell me, you Consider the Red Green show to be a Religion? LOL

Heh.. I have seen that show a few times and it has always made me laugh
out loud.


...snippage...
I'd move it, but you'd have to pay for gas and ferry to get me there
and back! What's your guess on its weight?

Oh, I'd gladly pay more than that. I'm looking at a 24' truck with lift
gate -- gotta see how much that lift gate can lift. If not enough (and
I expect it won't be) I might just take you up on that!

Weight is 3,000 lbs for the lathe. The other tools are all sub-1000
pounders and, hence, no problem even for the lift gate thang.

Jeez, I kinda dread this move. What an ordeal. But the end result will
be worth it..

Well, I usually charge $50/hour for me and the truck (plus ferry but
fuel is included) I can lift 7,000 lbs up close and I'm not sure what
the knuckle boom can lift 20' out, but if I can get close enough to
your equipment I should be able to pick and set it on a truck
easily... if you're not moving too far, we could strap them all to my
truck and make moving IN at the new place a breeze....

Think of it as being a patron of the arts since I'm just trying to
help pay for the truck that moves my sculpture around...

James, Port Orchard

plywood as above plus

http://www.grainger.com/Grainger/pro...777302&ccitem=

Hey Doug... I got your email but " seems to be
invalid... if you send me another email, try a REAL address. :-)

James, Port Orchard.


On Fri, 03 Sep 2004 06:29:27 GMT, Doug Smith
wrote:

RainLover wrote:
...snippage...
Don't tell me, you Consider the Red Green show to be a Religion? LOL

Heh.. I have seen that show a few times and it has always made me laugh
out loud.


...snippage...
I'd move it, but you'd have to pay for gas and ferry to get me there
and back! What's your guess on its weight?

Oh, I'd gladly pay more than that. I'm looking at a 24' truck with lift
gate -- gotta see how much that lift gate can lift. If not enough (and
I expect it won't be) I might just take you up on that!

Weight is 3,000 lbs for the lathe. The other tools are all sub-1000
pounders and, hence, no problem even for the lift gate thang.

Jeez, I kinda dread this move. What an ordeal. But the end result will
be worth it..

I know .. he did that to me lately recently too. Not even a link on his
Web page .. dude does NOT like spam, can't blame him.

Me, I handle putting email addy's out on the Web thusly:
http://www.tinyisland.com/email.html

I still get spam, though.

Grant

RainLover wrote:

Hey Doug... I got your email but " seems to be
invalid... if you send me another email, try a REAL address. :-)

James, Port Orchard.


On Fri, 03 Sep 2004 06:29:27 GMT, Doug Smith
wrote:


RainLover wrote:

...snippage...
Don't tell me, you Consider the Red Green show to be a Religion? LOL

Heh.. I have seen that show a few times and it has always made me laugh
out loud.



...snippage...
I'd move it, but you'd have to pay for gas and ferry to get me there
and back! What's your guess on its weight?

Oh, I'd gladly pay more than that. I'm looking at a 24' truck with lift
gate -- gotta see how much that lift gate can lift. If not enough (and
I expect it won't be) I might just take you up on that!

Weight is 3,000 lbs for the lathe. The other tools are all sub-1000
pounders and, hence, no problem even for the lift gate thang.

Jeez, I kinda dread this move. What an ordeal. But the end result will
be worth it..