Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
threaded grease/dustcaps
stryped wrote:
I have a trailer that I think uses very old truck or automotive axles. It is 6 bolt on 5.5 pattern. One set of axles has threaded grease caps which are missing. (The threads are on the outside of the hib, so in essence the grease cap is female and the hub is male). I just re greased the bearings and would like to replace these or fab somethign up but I have tried everywhere and cant find them. The threads are on the hub and look to be slightly over 2 inches and maybe fine thread. Can anyone help me????? I am about to go crazy! No trailer parts store, or anythign online has them. Got a lathe ? -- Snag Learning keeps you young ! |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
threaded grease/dustcaps
"Snag" wrote in message ... stryped wrote: I have a trailer that I think uses very old truck or automotive axles. It is 6 bolt on 5.5 pattern. One set of axles has threaded grease caps which are missing. (The threads are on the outside of the hib, so in essence the grease cap is female and the hub is male). I just re greased the bearings and would like to replace these or fab somethign up but I have tried everywhere and cant find them. The threads are on the hub and look to be slightly over 2 inches and maybe fine thread. Can anyone help me????? I am about to go crazy! No trailer parts store, or anythign online has them. Got a lathe ? Sounds like maybe "bearing buddies"...typically these are installed onto boat trailer wheel hubs so that one can easily flush water and replace with fresh grease after each launch. --IF so, suggest check a local marina... http://www.google.com/search?hl=en&r...1440&bih=83 9 |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
threaded grease/dustcaps
On Jun 13, 7:45*pm, "PrecisionmachinisT"
wrote: "Snag" wrote in message ... stryped wrote: I have a trailer that I think uses very old truck or automotive axles. It is 6 bolt on 5.5 pattern. One set of axles has threaded grease caps which are missing. (The threads are on the outside of the hib, so in essence the grease cap is female and the hub is male). *I just re greased the bearings and would like to replace these or fab somethign up but I have tried everywhere and cant find them. The threads are on the hub and look to be slightly over 2 inches and maybe fine thread. Can anyone help me????? I am about to go crazy! No trailer parts store, or anythign online has them. Got a lathe ? Sounds like maybe "bearing buddies"...typically these are installed onto boat trailer wheel hubs so that one can easily flush water and replace with fresh grease after each launch. --IF so, suggest check a local marina... I thought about those. But my problem is the size. The inside diameter of the openign is about 2.1 inches. Outside opening is 2.7. I would need a bearing buddy that is roughly 2.1 inhes. They have a 1.98, but that is the closest I could find. http://www.google.com/search?hl=en&r...dies&um=1&ie=U... |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Building an axle puller- Source for hardened threaded rod/screws, andthrough-hole threaded material for same? | Metalworking | |||
source of threaded rod? | Metalworking | |||
Lithium grase + silicone grease vs. axle grease | UK diy | |||
Threaded Rod Expert Out There? | Metalworking | |||
Special threaded rod. | Metalworking |