Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
hi all!
i am starting a hobby project where i need to weld a lot of 2" 1/4wall square tubing. a lot of miter cuts etc. can someone please suggest a good welder for this specific case? i have some tig & mig experienec but don't currently own a welder myself. i was looking at the miller maxstar tig and the millermatic. any suggestions are welcome. thanks, -p |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
wrote:
i am starting a hobby project where i need to weld a lot of 2" 1/4wall square tubing. a lot of miter cuts etc. can someone please suggest a good welder for this specific case? i have some tig & mig experienec but don't currently own a welder myself. i was looking at the miller maxstar tig and the millermatic. Can't suggest brands, but you want a MIG/MAG, _not_ a TIG. Nick -- Motor Modelle // Engine Models http://www.motor-manufaktur.de DIY-DRO - YADRO - Eigenbau-Digitalanzeige |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
And your budget is?
|
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
|
#5
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
my budget is $1000
and this is a36 hot rolled steel tubing i am talking about btw. |
#6
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
wrote in message oups.com... hi all! i am starting a hobby project where i need to weld a lot of 2" 1/4wall square tubing. a lot of miter cuts etc. can someone please suggest a good welder for this specific case? i have some tig & mig experienec but don't currently own a welder myself. i was looking at the miller maxstar tig and the millermatic. any suggestions are welcome. thanks, -p Lincoln SP175 Plus. A great machine for around $700. Gas bottle extra. Do it once. Do it right. Steve |
#7
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
As others have said, you have two basic choices. You can stick weld
with a cheap buzz-box AC welder, probably $250 new and half that for used. However, it will take a bit of practice to learn to stick weld. Someone suggested 6011 rod, a good choice for penetration, but if appearance counts, try 6013. MIG is easier to learn, but for 1/4 inch steel, the smaller migs that run on 110VAC are not powerful enough. Someone suggested a 175 amp mig, that would run on 220VAC, and should work. Check the specs before you buy, to be sure that it is recommended for 1/4 inch steel. TIG is not generally used for 1/4 inch steel. I have a TIG welder that I use as a stick welder when I need to weld 1/4 inch steel. (More or less all TIG welders can be used as stick welders, but the reverse is not true). If you need full penetration for 1/4 inch thick steel, you may need to make a groove or leave a space to get to the bottom of the joint. Experiment, weld, and then cut it open and see what it looks like, try to break it with a hammer and a vise, etc. Richard wrote: hi all! i am starting a hobby project where i need to weld a lot of 2" 1/4wall square tubing. a lot of miter cuts etc. can someone please suggest a good welder for this specific case? i have some tig & mig experienec but don't currently own a welder myself. i was looking at the miller maxstar tig and the millermatic. any suggestions are welcome. thanks, -p -- http://www.fergusonsculpture.com Sculptures in copper and other metals |
#8
Posted to rec.crafts.metalworking
|
|||
|
|||
welding 2"-1/4 square tube?
|
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
End caps for 2" square tube | Metalworking | |||
Telescoping square tubes for e-wheel adjuster? | Metalworking | |||
Four questions form novice to welding | Metalworking | |||
Q: Welding Magnesium | Metalworking | |||
Sliding bearings for telescoping square tubing? | Metalworking |