Last week I had my Formica kitchen countertops replaced by Granite by a
subcontractor of Home Depot Expo. Although the new countertops look great,
I am concerned about the installation. Specially my concern is with the
granite bar that is in back of the sink and leads to the great room. The
bar was previously 15 1/2 inches wide by 90 inches in length. The 15
1/2 width sat on one side of a wall that was 4 3/4 inch wide. When the
measuring person came to my home, I asked him if I could extend the width to
17 1/2 inches, and he said that would be no problem.

After the installer took off the old counter and replaced it with the
granite one, he indicated to me that I would need more support due to all
the additional weight of the granite counter bar. He temporarily put 2
wooden sticks on each side of the bar and advised me to get and install 3
corbels or shelf brackets under the width. Home Depot or Lowes do not
carry "heavy" corbels or shelf brackets. I noticed Home Depot has a shelf
bracket that can carry 50 lbs of weight.

Should the granite installer be responsible to the "complete installation",
including the safe supporting of the granite bar? They tell me it is my
responsibility to add this additional support. What type of a craftsman
should be used to make the installation safe?

Any comments / suggestions would be appreciated.

--
Have a great day, except you spammers
To email, remove the obvious

.......

"Les" wrote in message
...
Last week I had my Formica kitchen countertops replaced by Granite by a
subcontractor of Home Depot Expo. Although the new countertops look
great,
I am concerned about the installation. Specially my concern is with the
granite bar that is in back of the sink and leads to the great room. The
bar was previously 15 1/2 inches wide by 90 inches in length. The 15
1/2 width sat on one side of a wall that was 4 3/4 inch wide. When the
measuring person came to my home, I asked him if I could extend the width
to
17 1/2 inches, and he said that would be no problem.

After the installer took off the old counter and replaced it with the
granite one, he indicated to me that I would need more support due to all
the additional weight of the granite counter bar. He temporarily put 2
wooden sticks on each side of the bar and advised me to get and install 3
corbels or shelf brackets under the width. Home Depot or Lowes do not
carry "heavy" corbels or shelf brackets. I noticed Home Depot has a shelf
bracket that can carry 50 lbs of weight.

Should the granite installer be responsible to the "complete
installation",
including the safe supporting of the granite bar? They tell me it is my
responsibility to add this additional support. What type of a craftsman
should be used to make the installation safe?

Any comments / suggestions would be appreciated.

--
Have a great day, except you spammers
To email, remove the obvious

You made a change in mid stream. Your going to have to pick up the pieces.

Hi Les,

I wouldn't put the blame on the installer at all. I think the guy
that measured your countertops should have said something and told you there
would be extra costs associated with the modification.
Your installer should be commended for having enough pride in his work
to mention you needed added support. These supports mentioned aren't too
much money anyways.
If your looking for a "heavy" set of brackets, go to your local
welding shop and have some made up. Probably won't cost you more than about
20 bucks (I own a welding business).
Hope that was of some help....Jim





"Les" wrote in message
...
Last week I had my Formica kitchen countertops replaced by Granite by a
subcontractor of Home Depot Expo. Although the new countertops look
great,
I am concerned about the installation. Specially my concern is with the
granite bar that is in back of the sink and leads to the great room. The
bar was previously 15 1/2 inches wide by 90 inches in length. The 15
1/2 width sat on one side of a wall that was 4 3/4 inch wide. When the
measuring person came to my home, I asked him if I could extend the width
to
17 1/2 inches, and he said that would be no problem.

After the installer took off the old counter and replaced it with the
granite one, he indicated to me that I would need more support due to all
the additional weight of the granite counter bar. He temporarily put 2
wooden sticks on each side of the bar and advised me to get and install 3
corbels or shelf brackets under the width. Home Depot or Lowes do not
carry "heavy" corbels or shelf brackets. I noticed Home Depot has a shelf
bracket that can carry 50 lbs of weight.

Should the granite installer be responsible to the "complete
installation",
including the safe supporting of the granite bar? They tell me it is my
responsibility to add this additional support. What type of a craftsman
should be used to make the installation safe?

Any comments / suggestions would be appreciated.

--
Have a great day, except you spammers
To email, remove the obvious

......

Complain to HD and expo. The measurer, or whoever at HD was incharge of
your install should have been made aware of extra support needed. You
paid extra for those Extra inches , right. So it should have been a
complete job. HD should fix it free.

The person who did the measuring worked for the same company as the
installers. Actually one of the 2 installers was one of 2 measurers who
all work for the same granite company subcontracted by home depot.

Just saw the manager of home depot who I ordered the countertops from, and
he said he will call the granite company tomorrow and get the issue revolved
to my satisfaction

--
Have a great day, except you spammers
To email, remove the obvious

.......
"Jim M" jim wrote in message ...
Hi Les,

I wouldn't put the blame on the installer at all. I think the guy
that measured your countertops should have said something and told you
there
would be extra costs associated with the modification.
Your installer should be commended for having enough pride in his
work
to mention you needed added support. These supports mentioned aren't too
much money anyways.
If your looking for a "heavy" set of brackets, go to your local
welding shop and have some made up. Probably won't cost you more than
about
20 bucks (I own a welding business).
Hope that was of some help....Jim





"Les" wrote in message
...
Last week I had my Formica kitchen countertops replaced by Granite by a
subcontractor of Home Depot Expo. Although the new countertops look
great,
I am concerned about the installation. Specially my concern is with the
granite bar that is in back of the sink and leads to the great room.
The
bar was previously 15 1/2 inches wide by 90 inches in length. The
15
1/2 width sat on one side of a wall that was 4 3/4 inch wide. When the
measuring person came to my home, I asked him if I could extend the
width
to
17 1/2 inches, and he said that would be no problem.

After the installer took off the old counter and replaced it with the
granite one, he indicated to me that I would need more support due to
all
the additional weight of the granite counter bar. He temporarily put 2
wooden sticks on each side of the bar and advised me to get and install
3
corbels or shelf brackets under the width. Home Depot or Lowes do not
carry "heavy" corbels or shelf brackets. I noticed Home Depot has a
shelf
bracket that can carry 50 lbs of weight.

Should the granite installer be responsible to the "complete
installation",
including the safe supporting of the granite bar? They tell me it is my
responsibility to add this additional support. What type of a craftsman
should be used to make the installation safe?

Any comments / suggestions would be appreciated.

--
Have a great day, except you spammers
To email, remove the obvious

......