I've been changing out bulbs and going to the LED lights. I really
like them and have swapped out 9 of them so far.

Yesterday though, I ran into a different situation. The outdoor light
over my family room sliding door is controlled by and X-10 switch.
I've done that for years and it is very handy as this is the most used
door in the house.

The light was "off" and I screwed the bulb in, and it lit partially.
Not full brightness, but just dull. When the timer came on, it went
to full brightness. Having it half on 24 hours takes away some of the
savings, but I guess it is still minimal security at night after the
normal off time. I also know not to replace the other X10 lights with
LED. They work fine with CFL.

On 10/21/2014 2:59 AM, Ed Pawlowski wrote:
I've been changing out bulbs and going to the LED lights. I really
like them and have swapped out 9 of them so far.

Yesterday though, I ran into a different situation. The outdoor light
over my family room sliding door is controlled by and X-10 switch.
I've done that for years and it is very handy as this is the most used
door in the house.

The light was "off" and I screwed the bulb in, and it lit partially.
Not full brightness, but just dull. When the timer came on, it went
to full brightness. Having it half on 24 hours takes away some of the
savings, but I guess it is still minimal security at night after the
normal off time. I also know not to replace the other X10 lights with
LED. They work fine with CFL.

I had the same problem with X10 dimmers and outdoor motion detector lights.
With CFL, I had to switch to X10 appliance modules with relays.
There's a resistor that puts current thru the lamp to allow you
to use the lamp switch to turn it on/off.
That resistor charged up the cap and the CFL flashed every few seconds.
Removing the resistor fixed that.

Non-dimmable LED's had much the same issues as CFL.
But the newer dimmable LED's work in the outside motion detectors
and SOME of the X10 lamp modules.
I still have one X10 wall-switch-dimmer that behaves exactly like yours.
I put an incandescent back in it and will wait to see what the next
generation leds do. If I used it much, I'd bite the bullet and swap
to a wall switch X10 module.

Ed Pawlowski wrote:
I've been changing out bulbs and going to the LED lights. I really
like them and have swapped out 9 of them so far.

Yesterday though, I ran into a different situation. The outdoor light
over my family room sliding door is controlled by and X-10 switch.
I've done that for years and it is very handy as this is the most used
door in the house.

The light was "off" and I screwed the bulb in, and it lit partially.
Not full brightness, but just dull. When the timer came on, it went
to full brightness. Having it half on 24 hours takes away some of the
savings, but I guess it is still minimal security at night after the
normal off time. I also know not to replace the other X10 lights with
LED. They work fine with CFL.

Hi,
That's odd, CFL gave me trouble like that, Philips dimmable LED has no
trouble.

In article ,
says...

I've been changing out bulbs and going to the LED lights. I really
like them and have swapped out 9 of them so far.

Yesterday though, I ran into a different situation. The outdoor light
over my family room sliding door is controlled by and X-10 switch.
I've done that for years and it is very handy as this is the most used
door in the house.

The light was "off" and I screwed the bulb in, and it lit partially.
Not full brightness, but just dull. When the timer came on, it went
to full brightness. Having it half on 24 hours takes away some of the
savings, but I guess it is still minimal security at night after the
normal off time. I also know not to replace the other X10 lights with
LED. They work fine with CFL.

The local control 'feature' turned out to be a blessing in my case. I
bought some dimmable LED strip for under the kitchen cabinets, planning
to control them with an X10 lamp module, dimming them at night. They
flickered badly and generally misbehaved, so I tried an appliance
module. Turns out, the small current that is bled through results in
the perfect light level for the night light! It doesn't take much to
light up an LED.

FYI, the "half on 24 hours" that you're now observing was there all
along. It's not sufficient to light up a conventional lamp, so you just
never noticed it. Rest assured, it was still consuming watts