Building another shed from the Better Barn plans. The plan calls for 2x6
joists to run to a 2x6 band that sits on top of a 2x8 mudsill. Some of the
tops of the joists are sticking up about 1/8 to 1/4 inch above the 2x6 band.

Here is the basic framing question....before you lay down the 3/4 plywood
floor, do you plane down the 2x6 joist so it's in line with the band joist.
Or does it really not matter that much.

The second question...the side walls go up first. The side walls are
sheathed right to the edges of the walls. When you build the back wall,
should the sheathing be attached to the ends of the side walls? The last
one I built I sheathed the back wall but there was a gap at the end of the
sidewalls where there was no 1/2" CDX.

Thanks for your time.

In article , (JohnnyC) says...
Building another shed from the Better Barn plans. The plan calls for 2x6
joists to run to a 2x6 band that sits on top of a 2x8 mudsill. Some of the
tops of the joists are sticking up about 1/8 to 1/4 inch above the 2x6 band.

Here is the basic framing question....before you lay down the 3/4 plywood
floor, do you plane down the 2x6 joist so it's in line with the band joist.
Or does it really not matter that much.

It really doesn't matter that much.

The second question...the side walls go up first. The side walls are
sheathed right to the edges of the walls. When you build the back wall,
should the sheathing be attached to the ends of the side walls?

Yes.

The last
one I built I sheathed the back wall but there was a gap at the end of the
sidewalls where there was no 1/2" CDX.

You can rip a narrow strip of plywood to fill the gap, but you lose the
effect of a solid plywood gusset going all the way to the corner. For a
small shed, that probably doesn't matter a whole lot, but if you are in
an earthquake or high wind zone, it might keep the building from folding
up like a house of cards.

--
For email, replace firstnamelastinitial
with my first name and last initial.

Larry Caldwell wrote:

In article , (JohnnyC) says...
Building another shed from the Better Barn plans. The plan calls for 2x6
joists to run to a 2x6 band that sits on top of a 2x8 mudsill. Some of
the tops of the joists are sticking up about 1/8 to 1/4 inch above the
2x6 band.

Here is the basic framing question....before you lay down the 3/4 plywood
floor, do you plane down the 2x6 joist so it's in line with the band
joist. Or does it really not matter that much.

It really doesn't matter that much.

The second question...the side walls go up first. The side walls are
sheathed right to the edges of the walls. When you build the back wall,
should the sheathing be attached to the ends of the side walls?

Yes.

The last
one I built I sheathed the back wall but there was a gap at the end of
the sidewalls where there was no 1/2" CDX.

You can rip a narrow strip of plywood to fill the gap, but you lose the
effect of a solid plywood gusset going all the way to the corner. For a
small shed, that probably doesn't matter a whole lot, but if you are in
an earthquake or high wind zone, it might keep the building from folding
up like a house of cards.

Think that's called a shear wall, to stop lateral movement.

This is a pretty good site. It explains everything when building a house.
Probably a bit of overkill since it's California but a good reference. And
the OP is only building a shed.
http://www.abag.ca.gov/bayarea/eqmap...ch3/sld001.htm
--
"You can lead them to LINUX
but you can't make them THINK"
Running Mandriva release 2008.0 free-i586 using KDE on i586