I need to install a basement sink located 4 feet from a main soil
basement stack. The 3" PVC main soil stack drains 3 fixtures (toilet,
kitchen sink, bath sink) on the above first floor. The following vent
configurations for the basement sink would use 1.5" PVC:

1. Install a (circuit) revent to stack.

2. Install a wet vent directly to the stack.

3. Install a (long) branch vent. The branch vent would have about 50
feet of horizontal 1.5" PVC with five 90-degree turns installed on the
basement ceiling. This would connect to a branch vent (1.5") PVC of
42 feet vertical length that connects to the main vent in the attic
and through the roof. Due to the length of this configuration, this
vent would not have a slope, but should be dry.

Which one of these three is best/acceptable? Thanks.

One story or two story house?

"Phisherman" wrote in message
...
I need to install a basement sink located 4 feet from a main soil
basement stack. The 3" PVC main soil stack drains 3 fixtures (toilet,
kitchen sink, bath sink) on the above first floor. The following vent
configurations for the basement sink would use 1.5" PVC:

1. Install a (circuit) revent to stack.

2. Install a wet vent directly to the stack.

3. Install a (long) branch vent. The branch vent would have about 50
feet of horizontal 1.5" PVC with five 90-degree turns installed on the
basement ceiling. This would connect to a branch vent (1.5") PVC of
42 feet vertical length that connects to the main vent in the attic
and through the roof. Due to the length of this configuration, this
vent would not have a slope, but should be dry.

Which one of these three is best/acceptable? Thanks.

On Dec 14, 5:05 pm, "EXT" wrote:
One story or two story house?

"Phisherman" wrote in message

...

I need to install a basement sink located 4 feet from a main soil
basement stack. The 3" PVC main soil stack drains 3 fixtures (toilet,
kitchen sink, bath sink) on the above first floor. The following vent
configurations for the basement sink would use 1.5" PVC:

1. Install a (circuit) revent to stack.

2. Install a wet vent directly to the stack.

3. Install a (long) branch vent. The branch vent would have about 50
feet of horizontal 1.5" PVC with five 90-degree turns installed on the
basement ceiling. This would connect to a branch vent (1.5") PVC of
42 feet vertical length that connects to the main vent in the attic
and through the roof. Due to the length of this configuration, this
vent would not have a slope, but should be dry.

Which one of these three is best/acceptable? Thanks.

4. Install an air admittance valve.
http://www.toolbase.org/Technology-I...ittance-valves

R

"Two story with basement" is the local terminology in USA, TN.

On Fri, 14 Dec 2007 17:05:12 -0500, "EXT"
wrote:

One story or two story house?

"Phisherman" wrote in message
.. .
I need to install a basement sink located 4 feet from a main soil
basement stack. The 3" PVC main soil stack drains 3 fixtures (toilet,
kitchen sink, bath sink) on the above first floor. The following vent
configurations for the basement sink would use 1.5" PVC:

1. Install a (circuit) revent to stack.

2. Install a wet vent directly to the stack.

3. Install a (long) branch vent. The branch vent would have about 50
feet of horizontal 1.5" PVC with five 90-degree turns installed on the
basement ceiling. This would connect to a branch vent (1.5") PVC of
42 feet vertical length that connects to the main vent in the attic
and through the roof. Due to the length of this configuration, this
vent would not have a slope, but should be dry.

Which one of these three is best/acceptable? Thanks.