Do you tape the joint with joint compound or thinset?

Or should I just tile the entire wall in the shower area all the way
up to the ceiling?

On Oct 3, 6:08 am, wrote:
Do you tape the joint with joint compound or thinset?

Or should I just tile the entire wall in the shower area all the way
up to the ceiling?

In my opinion, you should just tile to the ceiling. Mine isn't and if
I redo it it will be, ceiling and all.
Unless you have no water pressure, it will constantly get splashed,
which will lead to,
peeling or at least discoloration adding additional cleaning and
painting chores. If the drywall ever gets soaked,
(green board is water resistant not water proof) replacing it will
play hell with the top row of tile.
If you do decide to transition, do it above the tile for the reason
stated above.

On Wed, 03 Oct 2007 04:08:06 -0700, wrote:

Do you tape the joint with joint compound or thinset?

Or should I just tile the entire wall in the shower area all the way
up to the ceiling?

You can tile it all the way up if you like; probably easiest and most
durable.

If you want to transition, here's what I do.

I plan the transition so it falls about 1/4 to 1/2 inch below the top
edge of the top row of tiles. I just leave an open joint; no tape,
mud, thinset, or the like. I then tile the area, being careful to hold
the thinset back on the top row so the tile is only adhered to the
backer board. Then instead of grouting the very top joint between the
drywall and the tile, I use urethane or silicone caulk after the
drywall is painted. This has worked very well for me.

HTH,

Paul F.

wrote:
Do you tape the joint with joint compound or thinset?

Or should I just tile the entire wall in the shower area all the way
up to the ceiling?



I used Wonderboard all the way to the ceiling, and skimmed it with
"EasySand 120" setting-type joint compound from the top row of tiles to
the ceiling.

It's too soon to tell if this was a good idea or not.

Bob

On Oct 3, 12:53 pm, zxcvbob wrote:
wrote:
Do you tape the joint with joint compound or thinset?

Or should I just tile the entire wall in the shower area all the way
up to the ceiling?

I used Wonderboard all the way to the ceiling, and skimmed it with
"EasySand 120" setting-type joint compound from the top row of tiles to
the ceiling.

It's too soon to tell if this was a good idea or not.

Bob

Hi, I should have mentioned that the transition I need is on the wall
on a vertical joint. Where the back wall of the shower ends one
column of tiles goes beyond the shower door (outside the shower area)
and then the sheetrock starts - all on the same wall.

I assume that this last column of tiles - under these tiles - the
joint from hardibacker to sheetrock should be (outside the water area
of the shower.)

The other side of the shower - the tiles end right at a 90 degree
corner. So I'm guessing that I could use a corner bead over the
hardbacker and sheetrock - use jointcompound on the sheetrock side
maybe a little extra thinset on the hardibacker side and make
everything flush. I'm sure it sounds easier than it actually is but I
don't think it will be impossible.

Someone in the history of the world must have ran into this?

On Oct 3, 12:03 pm, Paul Franklin
wrote:
On Wed, 03 Oct 2007 04:08:06 -0700, wrote:
Do you tape the joint with joint compound or thinset?

Or should I just tile the entire wall in the shower area all the way
up to the ceiling?

You can tile it all the way up if you like; probably easiest and most
durable.

If you want to transition, here's what I do.

I plan the transition so it falls about 1/4 to 1/2 inch below the top
edge of the top row of tiles. I just leave an open joint; no tape,
mud, thinset, or the like. I then tile the area, being careful to hold
the thinset back on the top row so the tile is only adhered to the
backer board. Then instead of grouting the very top joint between the
drywall and the tile, I use urethane or silicone caulk after the
drywall is painted. This has worked very well for me.

HTH,

Paul F.

That sounds reasonable but I'm curious as to why you wouldn't put a
little thinset on that small 1/2 inch section of sheetrock? I think
the caulk at the top certainly sounds reasonable.

On Thu, 04 Oct 2007 13:00:33 -0700, wrote:

On Oct 3, 12:03 pm, Paul Franklin
wrote:
On Wed, 03 Oct 2007 04:08:06 -0700, wrote:
Do you tape the joint with joint compound or thinset?

Or should I just tile the entire wall in the shower area all the way
up to the ceiling?

You can tile it all the way up if you like; probably easiest and most
durable.

If you want to transition, here's what I do.

I plan the transition so it falls about 1/4 to 1/2 inch below the top
edge of the top row of tiles. I just leave an open joint; no tape,
mud, thinset, or the like. I then tile the area, being careful to hold
the thinset back on the top row so the tile is only adhered to the
backer board. Then instead of grouting the very top joint between the
drywall and the tile, I use urethane or silicone caulk after the
drywall is painted. This has worked very well for me.

HTH,

Paul F.

That sounds reasonable but I'm curious as to why you wouldn't put a
little thinset on that small 1/2 inch section of sheetrock? I think
the caulk at the top certainly sounds reasonable.

Anytime you have two dissimilar materials they are likely to move
slightly relative to each other with changes in temperature and
humidity. By not using thinset on the sheetrock edge, it allows for
this motion. The caulk is flexible so it can tolerate the movement.

Is it a huge deal in this case? I doubt it, but it's easy to do and
it's held up well for me.

Paul F.