Yes, I did google. What I found was some roll on stuff in ten foot wide
pieces, and cost about two grand.

I live in a 14 x 65 trailer. I finally cut a small poke hole in the ceiling,
there is 4 inches space between the top of the ceiling board, and the tin
roof. Is that enough to blow some cellulose?

Would be nice to find some UV resistant bubble wrap I could roll on, with
some tar to hold it down. What else can be done?

--

Christopher A. Young
Do good work.
It's longer in the short run
but shorter in the long run.
..
..

"Stormin Mormon" wrote
I live in a 14 x 65 trailer. I finally cut a small poke hole in the
ceiling,
there is 4 inches space between the top of the ceiling board, and the tin
roof. Is that enough to blow some cellulose?

That's a half inch more than typical 2"x4" wall. Keep in mind, you will
have to poke a hole to fill each cavity. First I would want to get an idea
b/4 poking holes, exactly how it's constructed, and _if_ there's already
insulation there. You should be able to reach about an R-15 value using this
stuff (sold widely around here, your area may differ). That's not a whole
lot of insulation for ceiling, but it sure would beat none.

http://www.cocooninsulation.com/highRValue.asp?Type=B

Stormin, I would use fiberglass, not that chopped up newspaper crap they
call cellulose insulation. It can be blown into that space. Look in the
yellow pages and see if you can find an insulation company that
specializes in insulating hard to access places. I did that about 9
years ago. I cut openings in the tops of the outside walls on either
end, and we taped the insulation blower hose to about 30 feet of 3/4"
pipe to use as a long handle. They carefully inserted the hose all the
way in through the opening, and slowly moved it side to side as they
pulled it out. I am sure they were not able to get 100% coverage, but
the did manage to get a bunch of insulation in. They showed up in a
pickup full of bags on insulation and a trailer mounted machine-- they
had only a few bags left over afterward. Cost was $300. MH was
slilghtly smaller than yours-- 12x63. I did use cellulose (didn't know
any better then), and have had no problems at all. However, the MH was
over-roofed with R panel, so virtually no chance of any leaks. If
cellulose ever gets wet, you can have serious mold problems. BTW,the
insulation made a huge difference in heating and cooling. Larry

"lp13-30" wrote in message
...
Stormin, I would use fiberglass, not that chopped up newspaper crap they
call cellulose insulation. It can be blown into that space. Look in the
yellow pages and see if you can find an insulation company that
specializes in insulating hard to access places. I did that about 9
years ago. I cut openings in the tops of the outside walls on either
end, and we taped the insulation blower hose to about 30 feet of 3/4"
pipe to use as a long handle. They carefully inserted the hose all the
way in through the opening, and slowly moved it side to side as they
pulled it out. I am sure they were not able to get 100% coverage, but
the did manage to get a bunch of insulation in. They showed up in a
pickup full of bags on insulation and a trailer mounted machine-- they
had only a few bags left over afterward. Cost was $300. MH was
slilghtly smaller than yours-- 12x63. I did use cellulose (didn't know
any better then), and have had no problems at all. However, the MH was
over-roofed with R panel, so virtually no chance of any leaks. If
cellulose ever gets wet, you can have serious mold problems. BTW,the
insulation made a huge difference in heating and cooling. Larry


Read the warning label on the cellulose package.

Pay particular attention to the metal corrosion statement.


--
Colbyt
One picture can be worth a 1000 words.
Post yours at www.alt-home-repair.com for FREE.
No Banners, No pop-ups, No Spam, No hassle.