Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
I need ideas for a support bearing for a spinning table.
Jack R wrote: I need to spin a 24 inch round table at about 150 RPM several hours a day. The motor will drive a belt going around just under the table at a circumference that allows the slow speed. What I can't find is a lazy susan or bearing that I can attach under the spinning table and to the top of my work stand. Because the motor is driving the table it is also pulling it sideways so a standard lazy susan bearing might not work as they are designed for force downward, not sideways. Any thoughts. What are you going to do with this thingamajig? Cosmetics important? If you can find a junk potter's wheel, it might work. |
#2
|
|||
|
|||
"Jack R" wrote in message ... I need to spin a 24 inch round table at about 150 RPM several hours a day. The motor will drive a belt going around just under the table at a circumference that allows the slow speed. What I can't find is a lazy susan or bearing that I can attach under the spinning table and to the top of my work stand. Because the motor is driving the table it is also pulling it sideways so a standard lazy susan bearing might not work as they are designed for force downward, not sideways. Any thoughts. i built a 24" lap grinder that spins at around 125 rpm under load. i used the following plans: http://mrcol.freeyellow.com/grinder/...ap_grinder.htm and just scaled them up for 24". i used 2 pillow blocks and a couple of pulleys to make the arbor, and 2 flange blocks to support the axle. chose the pulley sizes to get the speed you want. if you want my spreadsheet that has the part numbers and places i used, send me an email. remove the obvious from the address. |
#3
|
|||
|
|||
Charles Spitzer wrote:
i built a 24" lap grinder that spins at around 125 rpm under load... Ouch! |
#4
|
|||
|
|||
On Thu, 07 Apr 2005 11:14:45 -0700, Jack R
wrote: I need to spin a 24 inch round table at about 150 RPM several hours a day. Any thoughts. 150rpm is quite fast for 24inch diameter. It's fast enough to need things fastening down to it. For a hub, go to a scrapyard and get a car front hub. Something with a Macpherson strut often allows easy unbolting and re-mounting. A brake disk can make a base for the table. Rubber toothed belt drives will easily drive by friction alone onto a turned cast iron cylinder and a toothed pinion on the small diameter motor shaft. |
#5
|
|||
|
|||
Andy Dingley wrote:
On Thu, 07 Apr 2005 11:14:45 -0700, Jack R wrote: I need to spin a 24 inch round table at about 150 RPM several hours a day. Any thoughts. 150rpm is quite fast for 24inch diameter. It's fast enough to need things fastening down to it. For a hub, go to a scrapyard and get a car front hub. Something with a Macpherson strut often allows easy unbolting and re-mounting. A brake disk can make a base for the table. Rubber toothed belt drives will easily drive by friction alone onto a turned cast iron cylinder and a toothed pinion on the small diameter motor shaft. Current Dodge truck front hubless designs come to mind. Maybe the 1 ton model, 2000, 2001 year. Bottom flange ( inboard on the truck ) will have 4 threaded holes so you can bolt it to something. The top flange ( outboard on the truck, where the rotor and wheel attach ) will have eight studs. Maybe 5-6" total height. Nice big ol' tapered bearings in there, too. That'll handle a load!! And guess what? With rim / tire assembly on the vehicle, it turns out to be almost a 24" diameter if not more. Put a side force on it all you want, that's how they work in their designed environment. Multi-directional load. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
(Sort of) sleeper wall problem: any ideas? | UK diy | |||
Chain tensioner ideas | Metalworking | |||
Base cabinets and low wall to support granite countertops | Woodworking | |||
Sony G410R Monitor problem (and bad Sony support) | Electronics Repair |