Does the old (circa 1986) Sony KV-20XBR have a service menu or service
mode? I just received the TV back from the repair shop this week after
a flyback, and some other ancillary parts (HOT), replacement. All is
basically fine with the set, except the convergence appears to be a bit
off as compared to what it was previously.

I'm just wondering whether it has a service mode, or you must converge
the set the "old fashioned" way? I have the necessary convergence test
equipment, but no technical info.

Also, were may I find a service pack, i.e. schematics, etc. for this
set. Are Sam's PhotoFacts, or equivalent, still available?

Thanks,
Don W9CW

Try this

http://myweb.accessus.net/~090/sonyadj.html

Regards


--
______________________
Danilo Ll. f: 56-8-9533942





"Don Allen" escribió en el mensaje
...
Does the old (circa 1986) Sony KV-20XBR have a service menu or service
mode? I just received the TV back from the repair shop this week after
a flyback, and some other ancillary parts (HOT), replacement. All is
basically fine with the set, except the convergence appears to be a bit
off as compared to what it was previously.

I'm just wondering whether it has a service mode, or you must converge
the set the "old fashioned" way? I have the necessary convergence test
equipment, but no technical info.

Also, were may I find a service pack, i.e. schematics, etc. for this
set. Are Sam's PhotoFacts, or equivalent, still available?

Thanks,
Don W9CW

On Sat, 10 Jul 2004 11:31:31 -0400, "Danilo Llorens R."
wrote:

Try this

http://myweb.accessus.net/~090/sonyadj.html

Regards


Not this one. Ancient models doesn't have service mode support.
KV-20XBR came out in 1985. I know because I had one in shop last week
for a estimate and the flyback transformer was split.

Cheers,

Wizard



--
______________________
Danilo Ll. f: 56-8-9533942





"Don Allen" escribió en el mensaje
m...
Does the old (circa 1986) Sony KV-20XBR have a service menu or service
mode? I just received the TV back from the repair shop this week after
a flyback, and some other ancillary parts (HOT), replacement. All is
basically fine with the set, except the convergence appears to be a bit
off as compared to what it was previously.

I'm just wondering whether it has a service mode, or you must converge
the set the "old fashioned" way? I have the necessary convergence test
equipment, but no technical info.

Also, were may I find a service pack, i.e. schematics, etc. for this
set. Are Sam's PhotoFacts, or equivalent, still available?

Thanks,
Don W9CW

This model does not have a service mode. The convergence in some models of
Sony XBR's have some pots on part of the scan board for trimming the
convergence and the pin set-up. The corners are also done with slip magnets.
All of the tubes use ring magnets for the centre convergence, and purity
set-up.

I suggest you DO NOT mess with the convergence, unless you have the proper
pattern generator, and know exactly what to do. I have seen a lot of people
really screw up their sets with this, and many service men are not very good
at doing convergence.

The main part of the convergence is done on the CRT with ring magnets, and
on the sides of the tube with slip magnets, as like all other TV sets.

In the service modes of TV sets that have a service mode, I have not very
often seen convergence controls.

After changing the flyback in these models, it is very possible that the
convergence can be effected. I am surprised that the service man did not
check this out!

Also, did you have the tube manually degaussed after the set was
re-installed? After a number of power cycles the internal degaussing coil
may clear this up over time, if it is a magnetism problem on the mask of the
tube, and not from the characteristics difference with the new flyback.

If you sent your set to an authorized Sony service centre, I would be
surprised if the set would be delivered with bad convergence. This is one of
the things that is specified to check when doing any type of horiz scan
servicing, or power supply servicing.

Another thing that interests me, is that why would someone want to put in
good money on a 1986 set? Many of the parts are no longer available from
Sony. I am sure that the tech must have used some type of generic
replacement flyback. I have sometimes had problems with these. I would also
be surprised of the picture tube is not soft by now. Considering the age of
many of the other components in the set, I would not expect it to be very
reliable over the long run.

You can get a very good 20 inch Sony TV these days for under $400 US. The
new set would be superior to a 18 year old set, and also have a descent
warranty. The new set would probably last you at least 6 to 10 years, which
I doubt you will get out of your 1986 set, since the repair.


--

Jerry G. GLG Technologies GLG
==========================




"Don Allen" escribió en el mensaje
...
Does the old (circa 1986) Sony KV-20XBR have a service menu or service
mode? I just received the TV back from the repair shop this week after
a flyback, and some other ancillary parts (HOT), replacement. All is
basically fine with the set, except the convergence appears to be a bit
off as compared to what it was previously.

I'm just wondering whether it has a service mode, or you must converge
the set the "old fashioned" way? I have the necessary convergence test
equipment, but no technical info.

Also, were may I find a service pack, i.e. schematics, etc. for this
set. Are Sam's PhotoFacts, or equivalent, still available?

Thanks,
Don W9CW