Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
How do you converge a direct view ATC221 chassis?
I personally have a 34" direct-view HDTV based on the ATC221 chassis
(D34EW11), I bought the thompson CD to figgure out how to correct some geometry errors and converge it, but I can only find references to converging the projection version of the chassis in the manual. There is no convergence selection in the service menu. I'm guessing if I opened it up, there would be at a minimum static convergence rings around the crt neck, but there must be more than that. I did a full-text search of every file on the CD, the only references to convergence are the PTV models. Any clues? Thanks. |
#2
|
|||
|
|||
How do you converge a direct view ATC221 chassis?
For all the standard consumer sets, there are only the static rings at the
back of the yoke. The most inner ones on most sets are the purity rings. On the walls of the tube, extending down under the yoke windings are the slip magnets for the sides, and corners. On the wall of the tube, there may be some button magnets, that are for the fine pin adjustments, and for the outer edge or corner purity. The tolerance of the shadowmask in the CRT, and the CRT is also very important for the accuracy of the convergence and purity. In the consumer sets, unless it is a very high model, there are no convergence controls in any of the menus or service mode. Most sets only have some basic pin adjustments in the service menu. This is all very tricky to mess with, and if you are not very experienced, you will end up making the set worse than it is. -- Greetings, Jerry Greenberg GLG Technologies GLG ========================================= WebPage http://www.zoom-one.com Electronics http://www.zoom-one.com/electron.htm ========================================= "Aaron Nabil" wrote in message om... I personally have a 34" direct-view HDTV based on the ATC221 chassis (D34EW11), I bought the thompson CD to figgure out how to correct some geometry errors and converge it, but I can only find references to converging the projection version of the chassis in the manual. There is no convergence selection in the service menu. I'm guessing if I opened it up, there would be at a minimum static convergence rings around the crt neck, but there must be more than that. I did a full-text search of every file on the CD, the only references to convergence are the PTV models. Any clues? Thanks. |
#3
|
|||
|
|||
How do you converge a direct view ATC221 chassis?
You need Chipper Checker ...and software.
MCM has them on sale. kip -- "Watch the return E-Mail addy its false" "Aaron Nabil" wrote in message om... I personally have a 34" direct-view HDTV based on the ATC221 chassis (D34EW11), I bought the thompson CD to figgure out how to correct some geometry errors and converge it, but I can only find references to converging the projection version of the chassis in the manual. There is no convergence selection in the service menu. I'm guessing if I opened it up, there would be at a minimum static convergence rings around the crt neck, but there must be more than that. I did a full-text search of every file on the CD, the only references to convergence are the PTV models. Any clues? Thanks. |
#4
|
|||
|
|||
How do you converge a direct view ATC221 chassis?
Mechanicl adjustments of convergence and purity rings on the neck of the crt
and physical location of the yoke. Like any other Direct View Tele. Might want to use a 1080 convergence patteren tho. "john" wrote in message .. . You need Chipper Checker ...and software. MCM has them on sale. kip -- "Watch the return E-Mail addy its false" "Aaron Nabil" wrote in message om... I personally have a 34" direct-view HDTV based on the ATC221 chassis (D34EW11), I bought the thompson CD to figgure out how to correct some geometry errors and converge it, but I can only find references to converging the projection version of the chassis in the manual. There is no convergence selection in the service menu. I'm guessing if I opened it up, there would be at a minimum static convergence rings around the crt neck, but there must be more than that. I did a full-text search of every file on the CD, the only references to convergence are the PTV models. Any clues? Thanks. |
#5
|
|||
|
|||
How do you converge a direct view ATC221 chassis?
Sorry thought it Pro Set
kip -- "Watch the return E-Mail addy its false" "Art" wrote in message ... Mechanicl adjustments of convergence and purity rings on the neck of the crt and physical location of the yoke. Like any other Direct View Tele. Might want to use a 1080 convergence patteren tho. "john" wrote in message .. . You need Chipper Checker ...and software. MCM has them on sale. kip -- "Watch the return E-Mail addy its false" "Aaron Nabil" wrote in message om... I personally have a 34" direct-view HDTV based on the ATC221 chassis (D34EW11), I bought the thompson CD to figgure out how to correct some geometry errors and converge it, but I can only find references to converging the projection version of the chassis in the manual. There is no convergence selection in the service menu. I'm guessing if I opened it up, there would be at a minimum static convergence rings around the crt neck, but there must be more than that. I did a full-text search of every file on the CD, the only references to convergence are the PTV models. Any clues? Thanks. |
#6
|
|||
|
|||
How do you converge a direct view ATC221 chassis?
I have the chipper check manual (it's on the CD), it also only
mentions convergence for PTV's. It has a few other functions, but mostly it seems to duplicate what is already available from the service menu. Are you _sure_ a chipper check will allow me to converge my DVTV? "john" wrote in message ... You need Chipper Checker ...and software. MCM has them on sale. kip -- "Watch the return E-Mail addy its false" "Aaron Nabil" wrote in message om... I personally have a 34" direct-view HDTV based on the ATC221 chassis (D34EW11), I bought the thompson CD to figgure out how to correct some geometry errors and converge it, but I can only find references to converging the projection version of the chassis in the manual. There is no convergence selection in the service menu. I'm guessing if I opened it up, there would be at a minimum static convergence rings around the crt neck, but there must be more than that. I did a full-text search of every file on the CD, the only references to convergence are the PTV models. Any clues? Thanks. |
#7
|
|||
|
|||
How do you converge a direct view ATC221 chassis?
|
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Tech Review: Victor's (8liners/Genao) Replacement Arcade RGB Monitor Chassis (LONG) | Electronics Repair | |||
Need Sony Monitor schematic CDM-5021PT | Electronics Repair |