THe middle 4 go in but one on each end doesn't.

I can't figure out if there's a way to change the head.

I think I've had this problem before and had a workaround but
can't recall

Why not essentially make an awl/screwdriver type push down tool that also
takes up less space?


- = -
Vasos Panagiotopoulos, Columbia'81+, Reagan, Mozart, Pindus, BioStrategist
http://www.panix.com/~vjp2/vasos.htm
---{Nothing herein constitutes advice. Everything fully disclaimed.}---
[Homeland Security means private firearms not lazy obstructive guards]
[Urb sprawl confounds terror] [Phooey on GUI: Windows for subprime Bimbos]

On Thu, 1 Aug 2013 00:09:09 +0000 (UTC),
wrote:

The middle 4 go in but one on each end doesn't.

That's what an 8 pin RJ45 crimper will do if you try to crimp a 4 pin
RJ11 connector. The end push pins ride up on the wide edges of the
plastic connector. Are you using an RJ11/14 die or something else?

On some crimpers, you can also produce that effect by not pushing the
plastic plug all the way into the crimper die.

I can't figure out if there's a way to change the head.

Some change the head, others change a die. Some have an insert.
You'll need to disclose what you have before that can be determined.

I think I've had this problem before and had a workaround but
can't recall

Why not essentially make an awl/screwdriver type push down tool that also
takes up less space?

It takes quite a bit of force to crimp those connectors. A 4 pin RJ11
may not take much force, but the 10 pin RJ50 requires leverage.

--
Jeff Liebermann
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

It's an RJ11 "plier" crimper. Seems designed for four pins.

White plastic. THe handle has some sort of template for smaller connectors

Maybe my old workaround was to get connectors with only 4 pins?

- = -
Vasos Panagiotopoulos, Columbia'81+, Reagan, Mozart, Pindus, BioStrategist
http://www.panix.com/~vjp2/vasos.htm
---{Nothing herein constitutes advice. Everything fully disclaimed.}---
[Homeland Security means private firearms not lazy obstructive guards]
[Urb sprawl confounds terror] [Phooey on GUI: Windows for subprime Bimbos]

wrote:
It's an RJ11 "plier" crimper. Seems designed for four pins.

White plastic. THe handle has some sort of template for smaller connectors

Maybe my old workaround was to get connectors with only 4 pins?

There are several kinds of plugs. They are listed by the number of pins
and places for pins.

The small ones for headphones are called 4P4C (4 pins, 4 connectors).

The usual ones, also called RJ-11 are 4P6C, 4 pins, 6 connectors. The
center 4 are used, the outer 2 are not. This is the standard for telephone
lines as the center 2 are tip and ring, and the next 2 out (one one
each side) are tip and ring for a second phone line, or a third wire for
ringer, and a fourth for ground, and in the 1960's low voltage AC
for dial lights (back when they were bulbs).

The next step up is the 6P6C, where all 6 connectors in the plug are
filled. They are rare and are not normally used for telephones, so it
it possible that you have a 4P6C crimper and are trying to crimp
6P6C plugs in it.

From my experience the cheap white crimp tools sold in home repair
stores etc, are not very good and require a steady but slow hand or you
will squeeze too hard and break them.

Geoff.


--
Geoffrey S. Mendelson, N3OWJ/4X1GM/KBUH7245/KBUW5379

*+-it possible that you have a 4P6C crimper and are trying to crimp
*+-6P6C plugs in it.

Unfortunately I suspect same. Much obliged, though.



- = -
Vasos Panagiotopoulos, Columbia'81+, Reagan, Mozart, Pindus, BioStrategist
http://www.panix.com/~vjp2/vasos.htm
---{Nothing herein constitutes advice. Everything fully disclaimed.}---
[Homeland Security means private firearms not lazy obstructive guards]
[Urb sprawl confounds terror] [Phooey on GUI: Windows for subprime Bimbos]

://www.web-design-hyderabad.in/seo-course-in-neredmet/


Contact for advisor : +91 9177522892

Web Design Hyderabad has a great demand and much more competition, But many of companies are not able to provide good service for customers, The problem might be because of design quality, not providing dynamic works like contact form or may be client expecting more work with very low cost.

To work with Web Design in Hyderabad, A designer should more honest with the client, you have to be explain the work of cost exactly, If not a designer will be struggled one day with client, Every one knows a designer can do any work but it takes time right, We have to cost as per our time

web design companies in hyderabad

Web design history

The Hypertext concept was invented by Ted Nelson in 60s, however it was used only for some decades after. During 1992 to 1994 other developers started adding up their own bits of HTML codes. HTML 1 tags and the HTML 2 born. As internet faster now the Web designers are putting more HTML capabilities. In 1995 more HTML tags have appeared and HTMl 3 was born. Now designers have an lot of option to use HTML B tables and style sheets and many more. They also have animated images, and Flash also introduced. It changed the whole landscape of web design from static to dynamic.

The first web site published in the World Wide Web history at sometime in August of 1981. It was some 30 years ago, however the Internet born in the sixties. It wasn’t fast as today. However it was capable in transferring information from one computer to another. Tim Berners was the first person who invented the World Wide Web. Tim Berners is British computer scientist. The First website launched in year 1990. on December 25 1990 with the help of Robert Cailliau and young student at CERN, Tim Berners implemented first successful communication between a Hypertext Transfer Protocol (HTTP) patron and server via Internet.