Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
Someone gave us this non working self propelled mower that he says
just stopped working. When my son first tried to start it he says that it would run for a few seconds and then quit. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. This morning we worked on it a little and I could not get it started at all. We ultimately found that there was no spark. I don't know what happened when he worked on it. The ignition kill switch is working, There is no short on that terminal in "run" position, the rust has been cleaned off both the rotor and stator areas of the flywheel and transformer and the plug of course looks OK too. There are no points or capacitor on this mower and there is just a magnet on the flywheel.The coil has a secondary wire to the plug, a terminal that is grounded to the transformer laminations with a self taping screw, and a terminal connected to the kill switch. Unless I'm missing something the operation of this system seems pretty cut and dried without timing or anything else being an issue, that as the magnet passes by the coil a voltage should be induced into the secondary. Am I correct in this assumption? Is there a way the positively bench test this coil before we go out a buy a new one that will no doubt be non returnable if it's not needed? Thanks, Lenny |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sat, 1 Sep 2012 12:57:03 -0700 (PDT), klem kedidelhopper
wrote: Someone gave us this non working self propelled mower that he says just stopped working. When my son first tried to start it he says that it would run for a few seconds and then quit. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. This morning we worked on it a little and I could not get it started at all. We ultimately found that there was no spark. I don't know what happened when he worked on it. The ignition kill switch is working, There is no short on that terminal in "run" position, the rust has been cleaned off both the rotor and stator areas of the flywheel and transformer and the plug of course looks OK too. There are no points or capacitor on this mower and there is just a magnet on the flywheel.The coil has a secondary wire to the plug, a terminal that is grounded to the transformer laminations with a self taping screw, and a terminal connected to the kill switch. Unless I'm missing something the operation of this system seems pretty cut and dried without timing or anything else being an issue, that as the magnet passes by the coil a voltage should be induced into the secondary. Am I correct in this assumption? Is there a way the positively bench test this coil before we go out a buy a new one that will no doubt be non returnable if it's not needed? Thanks, Lenny It's been a long time since I worked on lawn mower engines, but every one I ever saw had points and a capacitor. On vertical shaft engines they were typically under a cover under the flywheel. Now I will admit that this experience was well before the wide spread use of solid state devices, but there MUST be some method of interupting the primary circuit as the crankshaft nears top dead center. Also, the presence of a capacitor is pretty well mandatory. PlainBill |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
klem kedidelhopper wrote:
Someone gave us this non working self propelled mower that he says just stopped working. When my son first tried to start it he says that it would run for a few seconds and then quit. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. This morning we worked on it a little and I could not get it started at all. We ultimately found that there was no spark. I don't know what happened when he worked on it. The ignition kill switch is working, There is no short on that terminal in "run" position, the rust has been cleaned off both the rotor and stator areas of the flywheel and transformer and the plug of course looks OK too. There are no points or capacitor on this mower and there is just a magnet on the flywheel.The coil has a secondary wire to the plug, a terminal that is grounded to the transformer laminations with a self taping screw, and a terminal connected to the kill switch. Unless I'm missing something the operation of this system seems pretty cut and dried without timing or anything else being an issue, that as the magnet passes by the coil a voltage should be induced into the secondary. Am I correct in this assumption? Is there a way the positively bench test this coil before we go out a buy a new one that will no doubt be non returnable if it's not needed? Thanks, Lenny Have you downloaded the manual from Toro.com? May have a troubleshooting guide... Otherwise regular small engine repair books should be enough to get through the lack of spark problem. John :-#)# -- (Please post followups or tech enquiries to the newsgroup) John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games) www.flippers.com "Old pinballers never die, they just flip out." |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sep 1, 6:37*pm, John Robertson wrote:
klem kedidelhopper wrote: Someone gave us this non working self propelled mower that he says just stopped working. When my son first tried to start it he says that it would run for a few seconds and then quit. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. This morning we worked on it a little and I could not get it started at all. We ultimately found that there was no spark. I don't know what happened when he worked on it. The ignition kill switch is working, There is no short on that terminal in "run" position, the rust has been cleaned off both the rotor and stator areas of the flywheel and transformer and the plug of course looks OK too. There are no points or capacitor on this mower and there is just a magnet on the flywheel.The coil has a secondary wire to the plug, a terminal that is grounded to the transformer laminations with a self taping screw, and a terminal connected to the kill switch. Unless I'm missing something the operation of this system *seems pretty cut and dried without timing or anything else being an issue, that as the magnet passes by the coil a voltage should be induced into the secondary. Am I correct in this assumption? Is there a way the positively bench test this coil before we go out a buy a new one that will no doubt be non returnable if it's not needed? Thanks, Lenny Have you downloaded the manual from Toro.com? May have a troubleshooting guide... Otherwise regular small engine repair books should be enough to get through the lack of spark problem. John :-#)# -- * * (Please post followups or tech enquiries to the newsgroup) * John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 * Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games) * * * * * * * * * * *www.flippers.com * * * *"Old pinballers never die, they just flip out." These appear to be owners manuals. How to change the oil, etc. There really isn't anything mentioned that goes into anything that technical like bench testing a coil. I really think it is the coil. I just don't want to order one, about 20.00 and then possibly be stuck with it. Anyone have any ideas? Thanks, Lenny |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
klem kedidelhopper wrote:
... Anyone have any ideas? Thanks, Lenny I just went through this. I didn't want to believe that the coil was bad (a new one was $40). But there isn't a way, that I know of, to bench test. If you don't have a spark, it's bad. To test: - remove the kill wire - remove the spark plug, attach the coil wire, & ground the plug - pull the cord & watch for a spark on the plug This is better than trying to get a spark between the coil wire & ground. Bob |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sep 2, 9:05*am, Bob Engelhardt wrote:
klem kedidelhopper wrote: ... Anyone have any ideas? Thanks, Lenny I just went through this. *I didn't want to believe that the coil was bad (a new one was $40). *But there isn't a way, that I know of, to bench test. *If you don't have a spark, it's bad. To test: - remove the kill wire - remove the spark plug, attach the coil wire, & ground the plug - pull the cord & watch for a spark on the plug This is better than trying to get a spark between the coil wire & ground. Bob Wow, 40.00 for a coil! I am probably facing the same thing. I hope you at least got a kiss out of it...Lenny |
#7
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sun, 2 Sep 2012 05:35:19 -0700 (PDT), klem kedidelhopper
wrote: On Sep 1, 6:37*pm, John Robertson wrote: klem kedidelhopper wrote: Someone gave us this non working self propelled mower that he says just stopped working. When my son first tried to start it he says that it would run for a few seconds and then quit. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. This morning we worked on it a little and I could not get it started at all. We ultimately found that there was no spark. I don't know what happened when he worked on it. The ignition kill switch is working, There is no short on that terminal in "run" position, the rust has been cleaned off both the rotor and stator areas of the flywheel and transformer and the plug of course looks OK too. There are no points or capacitor on this mower and there is just a magnet on the flywheel.The coil has a secondary wire to the plug, a terminal that is grounded to the transformer laminations with a self taping screw, and a terminal connected to the kill switch. Unless I'm missing something the operation of this system *seems pretty cut and dried without timing or anything else being an issue, that as the magnet passes by the coil a voltage should be induced into the secondary. Am I correct in this assumption? Is there a way the positively bench test this coil before we go out a buy a new one that will no doubt be non returnable if it's not needed? Thanks, Lenny Have you downloaded the manual from Toro.com? May have a troubleshooting guide... Otherwise regular small engine repair books should be enough to get through the lack of spark problem. John :-#)# -- * * (Please post followups or tech enquiries to the newsgroup) * John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 * Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games) * * * * * * * * * * *www.flippers.com * * * *"Old pinballers never die, they just flip out." These appear to be owners manuals. How to change the oil, etc. There really isn't anything mentioned that goes into anything that technical like bench testing a coil. I really think it is the coil. I just don't want to order one, about 20.00 and then possibly be stuck with it. Anyone have any ideas? Thanks, Lenny Yes. Look he http://home.howstuffworks.com/home-i...l-engines3.htm The pictorial diagram and the two pictures match what I remember from 50 years ago. I also see references to solid state ignition systems used on these engines, that came well after the time I worked on them. If you can pull the coil without finding any wires other than to the kill switch and to the spark plug, the problem must be either the coil, the magnet in the flywheel, the spark plug, or the spark plug wire. The spark plug would seem to be the only replaceable part other than the coil. PlainBill |
#8
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sat, 1 Sep 2012 12:57:03 -0700 (PDT), klem kedidelhopper
wrote: Someone gave us this non working self propelled mower that he says just stopped working. Model number of the Toro mower? When my son first tried to start it he says that it would run for a few seconds and then quit. How many seconds is a few? If it's about 2-4 seconds, then you've got spark and some fuel. My guess(tm) is that you have a clogged fuel filter at the end of a hose banging around in the fuel tank. Fish out the fuel filter and hose with a coat hanger and replace the filter. No, don't try to clean it... just replace it. There may also be a filter at the fuel entry hose to the carb. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. Yep. It takes that long for fuel to sloooooooowly ooooooze through the clogged fuel filter. This morning we worked on it a little and I could not get it started at all. Sigh. One giant step backwards. We ultimately found that there was no spark. Remove spark plug. Reconnect wire from ignition coil. Ground the plug some place convenient on the engine (not the gas tank). Crank. Do you see sparks? If not, check the points. There are no points or capacitor on this mower and there is just a magnet on the flywheel. Keep looking. The breaker points and condenser might be buried. http://home.howstuffworks.com/home-improvement/repair/how-to-repair-small-engines3.htm http://www.ehow.com/how-does_5008999_lawn-mower-magneto-work.html Perhaps if you supplied the model number, an exploded view might be found? How to test a magneto: http://www.ask.com/questions-about/How-to-Test-a-Magneto Shopping and todo list: 1. Fuel filter 2. Points and condenser. 3. Replace fuel line hoses if they're plugged or cracking. 4. Spark plug. 5. Clean out engine exhaust port from carbon buildup. 6. Clean out engine intake port from tar buildup. 7. Carb cleaner. 8. Check the magneto gap. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#9
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
Jeff Liebermann wrote:
On Sat, 1 Sep 2012 12:57:03 -0700 (PDT), klem kedidelhopper .... There are no points or capacitor on this mower and there is just a magnet on the flywheel. Keep looking. The breaker points and condenser might be buried. ... Lawnmowers haven't had points for 20 (30?, 40?) years. |
#10
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Mon, 03 Sep 2012 09:22:34 -0400, Bob Engelhardt
wrote: Jeff Liebermann wrote: On Sat, 1 Sep 2012 12:57:03 -0700 (PDT), klem kedidelhopper ... There are no points or capacitor on this mower and there is just a magnet on the flywheel. Keep looking. The breaker points and condenser might be buried. ... Lawnmowers haven't had points for 20 (30?, 40?) years. True. I hate it when I date myself. I haven't had a lawn for about 35 years. We don't have lawns in the deep dark forest. Most of my small engine repairs are on chain saws and weed whackers, many of which have points and condensers. If it's an old riding mower, it has points and condenser on the engine. If it's newer, it's an electronic ignition. I'll wait for the model number to be disclosed to be certain. My comments on the fuel system problems still apply. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#11
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sat, 1 Sep 2012 12:57:03 -0700 (PDT), klem kedidelhopper
wrote: Someone gave us this non working self propelled mower that he says just stopped working. When my son first tried to start it he says that it would run for a few seconds and then quit. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. This morning we worked on it a little and I could not get it started at all. We ultimately found that there was no spark. I don't know what happened when he worked on it. The ignition kill switch is working, There is no short on that terminal in "run" position, the rust has been cleaned off both the rotor and stator areas of the flywheel and transformer and the plug of course looks OK too. There are no points or capacitor on this mower and there is just a magnet on the flywheel.The coil has a secondary wire to the plug, a terminal that is grounded to the transformer laminations with a self taping screw, and a terminal connected to the kill switch. Unless I'm missing something the operation of this system seems pretty cut and dried without timing or anything else being an issue, that as the magnet passes by the coil a voltage should be induced into the secondary. Am I correct in this assumption? Is there a way the positively bench test this coil before we go out a buy a new one that will no doubt be non returnable if it's not needed? Thanks, Lenny Greetings Lenny, The electronics in the coil are probably bad. If you try the test suggested further down this thread and there is still no spark then it is very likely the electronics are bad. I have seen some coils that have the trigger electronics located in a bump on the coil. These types can sometimes be removed and replaced with aftermarket electronic ignition modules. It has been a long time since I've done this so maybe this won't work for you. The magneto works like this: the primary is grounded and the magnet passes quickly past the legs of the magneto assembly. At the proper moment the ground is disconnected and the collapsing field induces a voltage in the secondary. The aftermarket electronic ignitions sense the rising voltage and open the ground connection at the proper moment. So if you can get to the electronics and remove the connections, then figure out which wires are which, you can then maybe use an aftermarket module to make the thing work. Briggs and Stratton used to make an electronic ignition that worked differently than described above. It had some sort of coil that sensed the flywheeel position(Ithink). I never tried to hack one of those, just replaced parts. But I have repaired a few of the types described above. I have even just wired in an aftermarket electronic ignition on a weed trimmer that lost spark. The ignition module was made for a Tecumseh engine but since I had it already I just wired it the way I would have if I was retrofitting a points type ignition. The weed trimmer unit had obviously failed with the ground permanently connected and since the new module opens the ground to get spark it worked fine. If you don't mind a shock you can try what I do. I grab the spark plug wire and pull slowly on the starting rope. If I don't get even a tingle then I pull faster. If I get a good shock then that means either a bad spark plug or bad connections. If I just get a pretty good tingle then that probably means that the coil is being permanently grounded and I'm feeling the rising field. This is hopeful because it means that maybe an aftermarket ignition module will work since they just interrupt the ground. Whew! I didn't think this reply would be so long. Eric |
#12
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sep 4, 11:39*am, wrote:
On Sat, 1 Sep 2012 12:57:03 -0700 (PDT), klem kedidelhopper wrote: Someone gave us this non working self propelled mower that he says just stopped working. When my son first tried to start it he says that it would run for a few seconds and then quit. After this it would apparently take about 20 minutes before it would again start, and again run for about two seconds and then the process was repeated. This morning we worked on it a little and I could not get it started at all. We ultimately found that there was no spark. I don't know what happened when he worked on it. The ignition kill switch is working, There is no short on that terminal in "run" position, the rust has been cleaned off both the rotor and stator areas of the flywheel and transformer and the plug of course looks OK too. There are no points or capacitor on this mower and there is just a magnet on the flywheel.The coil has a secondary wire to the plug, a terminal that is grounded to the transformer laminations with a self taping screw, and a terminal connected to the kill switch. Unless I'm missing something the operation of this system *seems pretty cut and dried without timing or anything else being an issue, that as the magnet passes by the coil a voltage should be induced into the secondary. Am I correct in this assumption? Is there a way the positively bench test this coil before we go out a buy a new one that will no doubt be non returnable if it's not needed? Thanks, Lenny Greetings Lenny, The electronics in the coil are probably bad. If you try the test suggested further down this thread and there is still no spark then it is very likely the electronics are bad. I have seen some coils that have the trigger electronics located in a bump on the coil. These types can sometimes be removed and replaced with aftermarket electronic ignition modules. It has been a long time since I've done this so maybe this won't work for you. The magneto works like this: the primary is grounded and the magnet passes quickly past the legs of the magneto assembly. At the proper moment the ground is disconnected and the collapsing field induces a voltage in the secondary. The aftermarket electronic ignitions sense the rising voltage and open the ground connection at the proper moment. So if you can get to the electronics and remove the connections, then figure out which wires are which, you can then maybe use an aftermarket module to make the thing work. Briggs and Stratton used to make an electronic ignition that worked differently than described above. It had some sort of coil that sensed the flywheeel position(Ithink). I never tried to hack one of those, just replaced parts. But I have repaired a few of the types described above. I have even just wired in an aftermarket electronic ignition on a weed trimmer that lost spark. The ignition module was made for a Tecumseh engine *but since I had it already I just wired it the way I would have if I was retrofitting a points type ignition. The weed trimmer unit had obviously failed with the ground permanently connected and since the new module opens the ground to get spark it worked fine. If you don't mind a shock you can try what I do. I grab the spark plug wire and pull slowly on the starting rope. If I don't get even a tingle then I pull faster. If I get a good shock then that means either a bad spark plug or bad connections. If I just get a pretty good tingle then that probably means that the coil is being permanently grounded and I'm feeling the rising field. This is hopeful because it means that maybe an aftermarket ignition module will work since they just interrupt the ground. Whew! I didn't think this reply would be so long. Eric Wow Eric thanks for the theory. I think that it is a good bet that the electronics in the coil has failed. I'm pretty sure that I can get a used coil from a lawnmower repair guy in this area. There are a number of people that work on these and sell used mowers. I'm thinking that they must keep used parts around. I wish I could find the model number of this thing. Lenny |
#13
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Wed, 5 Sep 2012 10:18:38 -0700 (PDT), klem kedidelhopper
wrote: I wish I could find the model number of this thing. Lenny Ask and ye shall receive: http://www.jackssmallengines.com/toro_model_locator.cfm -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#14
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sep 5, 1:52*pm, Jeff Liebermann wrote:
On Wed, 5 Sep 2012 10:18:38 -0700 (PDT), klem kedidelhopper wrote: I wish I could find the model number of this thing. Lenny Ask and ye shall receive: http://www.jackssmallengines.com/toro_model_locator.cfm -- Jeff Liebermann * * 150 Felker St #D * *http://www.LearnByDestroying.com Santa Cruz CA 95060http://802.11junk.com Skype: JeffLiebermann * * AE6KS * *831-336-2558 How do you find this **** Jeff? It's a model 20016. Lenny |
#15
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Wed, 5 Sep 2012 12:06:48 -0700 (PDT), klem kedidelhopper
wrote: On Sep 5, 1:52*pm, Jeff Liebermann wrote: On Wed, 5 Sep 2012 10:18:38 -0700 (PDT), klem kedidelhopper wrote: I wish I could find the model number of this thing. Lenny Ask and ye shall receive: http://www.jackssmallengines.com/toro_model_locator.cfm How do you find this **** Jeff? It's a model 20016. Lenny I usually use a crystal ball. However, it's in the shop getting its temporal dimensional translator recalibrated. So, I had to settle for Google. A search for "Toro find serial number" immediately yielded the correct site on the first page (at the bottom). Here's the exploded view of the 20016: http://www.ereplacementparts.com/toro-20016-2600000012609999992006-lawn-mower-parts-c-121776_127291_127648.html Looking at the engine diagram, there are no points or condenser. Ok so I was wrong. Ignition coil: http://www.ereplacementparts.com/ignitionstate-solid-p-685744.html Oh swell... it's a special order. Digging for other vendors that carry a 34443D. http://www.ebay.com/sch/i.html?_nkw=34443d+coil $25. However, I'm still suspicious that it's a fuel problem based on the original symptoms. I'm not sure why it now doesn't have a spark. Performing at least one of several recommended test should help eliminate lack of spark as a probable cause. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#16
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Sep 6, 3:18*am, Jeff Liebermann wrote:
On Wed, 5 Sep 2012 12:06:48 -0700 (PDT), klem kedidelhopper wrote: On Sep 5, 1:52*pm, Jeff Liebermann wrote: On Wed, 5 Sep 2012 10:18:38 -0700 (PDT), klem kedidelhopper wrote: I wish I could find the model number of this thing. Lenny Ask and ye shall receive: http://www.jackssmallengines.com/toro_model_locator.cfm How do you find this **** Jeff? It's a model 20016. Lenny I usually use a crystal ball. *However, it's in the shop getting its temporal dimensional translator recalibrated. *So, I had to settle for Google. *A search for "Toro find serial number" immediately yielded the correct site on the first page (at the bottom). Here's the exploded view of the 20016: http://www.ereplacementparts.com/toro-20016-2600000012609999992006-la... Looking at the engine diagram, there are no points or condenser. *Ok so I was wrong. *Ignition coil: http://www.ereplacementparts.com/ignitionstate-solid-p-685744.html Oh swell... it's a special order. *Digging for other vendors that carry a 34443D. http://www.ebay.com/sch/i.html?_nkw=34443d+coil $25. However, I'm still suspicious that it's a fuel problem based on the original symptoms. *I'm not sure why it now doesn't have a spark. Performing at least one of several recommended test should help eliminate lack of spark as a probable cause. -- Jeff Liebermann * * 150 Felker St #D * *http://www.LearnByDestroying.com Santa Cruz CA 95060http://802.11junk.com Skype: JeffLiebermann * * AE6KS * *831-336-2558 I have eliminated an internally arcing spark plug as a possibility because I tried sticking a screw driver into the boot and acing it to ground and there was no spark with that method. In addition, with the shroud (with the starter pull rope) removed, and turning the engine with a drill the high voltage wire is well removed from chassis ground so it arcing is not the problem either. However now I think that I know what may have happened. I ran across the sites below that had really good writeups on small engine ignition theory. The second one happened to mention that you should never fire an ignition coil with the secondary disconnected from the spark plug or as they put it a "suitable load". The article went on to say that doing so could cause internal acing in the coil and damage it. I never knew this but it makes sense and incidentally adds up as well. I happened to mention this to my son this morning and he admitted that during the course of his working on the engine when he had it running for a few seconds and then it would die he had done this very thing. And mysteriously now we have no spark where he did before. So a new coil is about twenty five dollars and I'm thinking that should hopefully take us back to square one where we should be back to the two second run problem, (I hope). If I knew that it was just the coil I guess I'd spring for the twenty five bucks plus freight. However given the history with this engine I'd rather not go throwing a lot of money at something that may need a carburetor or more as well. I gotta go see the used lawn mower guys this week and hopefully find a coil. Lenny |
#17
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
klem kedidelhopper wrote:
... you should never fire an ignition coil with the secondary disconnected from the spark plug or as they put it a "suitable load". The article went on to say that doing so could cause internal acing in the coil and damage it. ... Although that sounds plausible, I'm skeptical. First, I don't see how an internal spark would happen. I.e., what the path would be. But even if it could, I've fired disconnected coils lots of times without problems. An alternative explanation would be that the coil was marginal at the start - good enough to run for the few seconds. Then failed altogether. I don't know if there is a coil failure mode like that, but I wouldn't rule it out. Bob |
#18
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
... you should never fire an ignition coil with the secondary
disconnected from the spark plug, or as they put it a "suitable load". The article went on to say that doing so could cause internal acing in the coil and damage it. ... Although that sounds plausible, I'm skeptical. First, I don't see how an internal spark would happen, ie, what the path would be. But even if it could, I've fired disconnected coils lots of times without problems. And how is external arcing "somewhere else" different from arcing across the spark plug's gap? |
#19
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Thu, 6 Sep 2012 06:18:03 -0700, "William Sommerwerck"
wrote: ... you should never fire an ignition coil with the secondary disconnected from the spark plug, or as they put it a "suitable load". The article went on to say that doing so could cause internal acing in the coil and damage it. ... Although that sounds plausible, I'm skeptical. First, I don't see how an internal spark would happen, ie, what the path would be. But even if it could, I've fired disconnected coils lots of times without problems. And how is external arcing "somewhere else" different from arcing across the spark plug's gap? When the coil creates a high voltage, there will be an arc wherever the gap is the smallest. That is supposed to be the spark plug. If the plug isn't there, it could arc inside the coil and thereby destroying some high voltage insulation. It is possible that from then on, the shortest gap is inside the coil. I am not saying that is what happened - just explaining what the warning meant. |
#20
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
Pat wrote:
When the coil creates a high voltage, there will be an arc wherever the gap is the smallest. ... it could arc inside the coil and thereby destroying some high voltage insulation. ... You're right, but there are limitations. First, the voltage isn't unlimited, it has some maximum, whether there's a gap or not. I don't know the mechanisms limiting it - parasitic capacitance, leakage current, I dunno. Hopefully the coil designer knew and insulated against it, maybe. Then there's the path of an internal arc. There's certainly not enough voltage for an arc between adjacent turns. Also very unlikely between adjacent layers. The highest voltage is between the last turn and the core. But that's the most heavily insulated path. I'd be convinced by an actual case of an internal arc - anybody ever see one? Bob |
#21
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Thu, 6 Sep 2012 05:08:32 -0700 (PDT), klem kedidelhopper
wrote: The second one happened to mention that you should never fire an ignition coil with the secondary disconnected from the spark plug or as they put it a "suitable load". The article went on to say that doing so could cause internal acing in the coil and damage it. I never knew this but it makes sense and incidentally adds up as well. I happened to mention this to my son this morning and he admitted that during the course of his working on the engine when he had it running for a few seconds and then it would die he had done this very thing. 90% baloney as usual. There are two ways to "run" an engine without a load on the ignition coil. One is to hand start the engine with the spark plug wire disconnected. That won't do any damage as there's not enough energy in the spark from hand cranking to do any damage. The other way is to run the engine for a while, and remove the spark plug wire. Assuming you can do this without getting a nasty shock, it might internally arc across the coil. However, in my limited experience with chain saws and small generator engines, a shorted coil will still generate a small arc. Not a hot or big as a normal coil, but unless the short is somehow across the entire coil (easily found with an ohmmeter test), you'll still see a tiny spark. Buy a real tester: http://www.ebay.com/sch/i.html?_trksid=p5197.m570.l1313&_nkw=spark+plug+te ster (I made my own spark gap from a piece of U shaped plastic). What I think happened here is that someone transplanted the story from their automobile or multi-cylinder engine experience. With more than one cyclinder, it is possible to run the engine with one spark plug wire disconnected, which might cause internal arcing. However, it's not likely with a single cylinder engine. Note that the coil part number that I excavated is used in Husqvarna, Tecumseh, Toro, and others. If it was as failure prone when NOT running as you imply, there would be recalls and other failures in epidemic numbers. Testing the ignition: http://www.youtube.com/watch?v=MNvwZmZj610 This one covers most ways to test your engine spark. http://www.youtube.com/watch?v=5qSgmunp_Ys -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#22
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
"Bob Engelhardt" wrote in message ... Pat wrote: I'd be convinced by an actual case of an internal arc - anybody ever see one? Bob Yes. Many. Thats how they fail. Temperature, vibration, aging induce small cracks in the insulation. Dirt, moisture infiltrate, etc. Better coils are designed with internal aux gaps greater than the normal spark plug gap. I've dissected failed coils, not hard to find traces of internal arcing, melting. |
#23
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
Bob Engelhardt wrote:
I'd be convinced by an actual case of an internal arc - anybody ever see one? Well, I had a B&S engine that would run for 10 minutes or so, and then get weak, sputter and finally die. if you let it sit for a couple minutes, it would start and run for 30 seconds or so and die again. A new spark coil fixed it completely, and it ran fine until the deck, wheel drive, etc. was completely worn out. Just had a problem with its replacement mower. it would run for about 20 minutes, start knocking, lose power and then die with a big blast of oil smoke, I guess it got hot enough to boil the oil out the crankcase vent, and sucked that into the carb. I cleaned the cooling passages, but that didn't help. It finally occurred to me the timing could be off, so I checked the shearable key on the flywheel, and it was sheared. I haven't run it for 20 minutes yet, but I'll be that was the problem, advanced spark timing. It does seem to run better though, I'll put the kids to work soon for a more exhaustive test of my repair. Jon |
#24
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
Replace the coil and be done Jerry |
#25
Posted to sci.electronics.repair
|
|||
|
|||
Toro self propelled lawn mower ignition problem
On Fri, 27 Feb 2015 09:08:17 -0800 (PST), wrote:
Replace the coil and be done Jerry HUH? I don't even own a Toro self propelled lawn mower! Oh, I see... Another google grooper... |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Toro Lawn Mower hard to start | Home Repair | |||
briggs and stratton yardman self propelled lawn mower carb problem | Home Repair | |||
Craftsman Self-Propelled Mower Problem | Home Repair | |||
Toro rear drive lawn mower | Home Repair | |||
Walk-Behind, Self Propelled, Lawn Mower Questions Re Toro & Craftsman ? | Home Repair |