Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
Over the past few months I've received a few cheapo LCD TVs with blown
power supplies that could not be repaired, the reason being that replacement parts (or whole boards) were simply not available. Another one just came in with the same problem, and this time an idea occurred to me. The power supplies in these sets are pretty simple, at least in terms of outputs and connections. They usually consist of a 5VDC standby supply and switchable 12 and 24VDV supplies. The standby voltage is always derived from a separate switching transformer, and it's usually the 12/24 volt circuit that goes bad. The connections are usually GND,5V,12v,24v, and power on signal. So the obvious question is - can an external power supply be added to the set? I once tried this but my homemade power supply wasn't filtered or regulated well enough to provide satisfactory operation. Looking on Ebay, I see that low-cost switching power supplies are readily available, in a wide assortment of voltages and amperages. I thought I might buy some and try creating external power supplies for these TVs, but first I'd like to know just how much current is required for a 27 to 32" TV. The 24 and 12V power supplies are available in current ratings of 2,3,5,10 amps and higher. A relay circuit would have to be added so that the backlights etc. wouldn't stay on when in power off mode. Adding an external power supply might not be as practical as replacing the internal one, but it's far cheaper and in some cases may be the only way to save the set from the landfill. |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
Chris F. wrote:
The power supplies in these sets are pretty simple, at least in terms of outputs and connections. They usually consist of a 5VDC standby supply and switchable 12 and 24VDV supplies. The standby voltage is always derived from a separate switching transformer, and it's usually the 12/24 volt circuit that goes bad. The connections are usually GND,5V,12v,24v, and power on signal. So the obvious question is - can an external power supply be added to the set? I once tried this but my homemade power supply wasn't filtered or regulated well enough to provide satisfactory operation. Looking on Ebay, I see that low-cost switching power supplies are readily available, in a wide assortment of voltages and amperages. I thought I might buy some and try creating external power supplies for these TVs, but first I'd like to know just how much current is required for a 27 to 32" TV. The 24 and 12V power supplies are available in current ratings of 2,3,5,10 amps and higher. A relay circuit would have to be added so that the backlights etc. wouldn't stay on when in power off mode. Adding an external power supply might not be as practical as replacing the internal one, but it's far cheaper and in some cases may be the only way to save the set from the landfill. Before you get excited... : think about *why* the supply died. Sure, it's possible that it just "gave up the ghost". But, it is also possible that some aspect of the *load* has changed in A Bad Way. Unless you fix the root cause, you stand a good chance of toasting your *new* supply... *or* something else in the set when it finds "enough" power available for it to cook itself without taking out the "semiconductor fuses" (otherwise known as transistors : ) in the power supply. |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
"D Yuniskis" wrote in message ... Chris F. wrote: The power supplies in these sets are pretty simple, at least in terms of outputs and connections. They usually consist of a 5VDC standby supply and switchable 12 and 24VDV supplies. The standby voltage is always derived from a separate switching transformer, and it's usually the 12/24 volt circuit that goes bad. The connections are usually GND,5V,12v,24v, and power on signal. So the obvious question is - can an external power supply be added to the set? I once tried this but my homemade power supply wasn't filtered or regulated well enough to provide satisfactory operation. Looking on Ebay, I see that low-cost switching power supplies are readily available, in a wide assortment of voltages and amperages. I thought I might buy some and try creating external power supplies for these TVs, but first I'd like to know just how much current is required for a 27 to 32" TV. The 24 and 12V power supplies are available in current ratings of 2,3,5,10 amps and higher. A relay circuit would have to be added so that the backlights etc. wouldn't stay on when in power off mode. Adding an external power supply might not be as practical as replacing the internal one, but it's far cheaper and in some cases may be the only way to save the set from the landfill. Before you get excited... : think about *why* the supply died. Sure, it's possible that it just "gave up the ghost". But, it is also possible that some aspect of the *load* has changed in A Bad Way. Unless you fix the root cause, you stand a good chance of toasting your *new* supply... *or* something else in the set when it finds "enough" power available for it to cook itself without taking out the "semiconductor fuses" (otherwise known as transistors : ) in the power supply. In my experience, most LCD TV internal power supplies fail for no other reason than that they just fail. Also, it is fairly rare that I find that the failure is on the secondary side, particularly in the 24v circuit, which normally feeds primarily the backlights, and sometimes the sound. For sure the 24v circuit may not appear to be working, but this is more often than not, because the backlight inverter has failed, and caused the supply to shut down. And whilst we are talking shutdown, it is very rare for faults external to the PSU to cause PSU damage. The switchers fitted to LCD TVs are absolutely *covered* in monitoring circuitry, and any overload condition on any rail, will bring about an immediate shutdown of all secondary supplies, and often, will place the standby supply into a cycling startup mode as well. Most of the failures that I come across involve either the standby supply, or the PFC supply, both of which are primary-side failures. There are many many 'service kits' available to deal with most of these failures, and they are usually quite reasonably priced. They contain all of the components which fail, and if you just go ahead and replace all the parts that they give you, irrespective of whether they appear to be faulty or not, you will usually end up with a working supply. Before totally writing off the existing supplies, you should probably try to diagnose your problems a little deeper, and then see if a kit is available. As to what the demand is on the various rails, they are all quite light except for the 24v rail, where the demand is typically around 4 amps. I use two 12v 50watt halogen lamps in series as a test load for the 24v rail. With regard to trying to use an 'alternative' supply, wired in externally, I personally would not consider doing this as I feel that you may be opening yourself up to all manner of potential safety issues, and certainly would be compromising any safety approvals that were already in place for the equipment. This could bring a whole legal ****storm down on your head, if anyone received any injury as a result ... Far better, I think, that the existing power supplies are repaired. Although diagnosing these supplies is a bit of a black art, contrary to what you believe, most are repairable, and most parts are available, if you look hard enough. Arfa |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
On Tue, 24 Nov 2009 14:46:58 -0000, "Arfa Daily"
wrote: "D Yuniskis" wrote in message ... Chris F. wrote: The power supplies in these sets are pretty simple, at least in terms of outputs and connections. They usually consist of a 5VDC standby supply and switchable 12 and 24VDV supplies. The standby voltage is always derived from a separate switching transformer, and it's usually the 12/24 volt circuit that goes bad. The connections are usually GND,5V,12v,24v, and power on signal. So the obvious question is - can an external power supply be added to the set? I once tried this but my homemade power supply wasn't filtered or regulated well enough to provide satisfactory operation. Looking on Ebay, I see that low-cost switching power supplies are readily available, in a wide assortment of voltages and amperages. I thought I might buy some and try creating external power supplies for these TVs, but first I'd like to know just how much current is required for a 27 to 32" TV. The 24 and 12V power supplies are available in current ratings of 2,3,5,10 amps and higher. A relay circuit would have to be added so that the backlights etc. wouldn't stay on when in power off mode. Adding an external power supply might not be as practical as replacing the internal one, but it's far cheaper and in some cases may be the only way to save the set from the landfill. Before you get excited... : think about *why* the supply died. Sure, it's possible that it just "gave up the ghost". But, it is also possible that some aspect of the *load* has changed in A Bad Way. Unless you fix the root cause, you stand a good chance of toasting your *new* supply... *or* something else in the set when it finds "enough" power available for it to cook itself without taking out the "semiconductor fuses" (otherwise known as transistors : ) in the power supply. In my experience, most LCD TV internal power supplies fail for no other reason than that they just fail. Also, it is fairly rare that I find that the failure is on the secondary side, particularly in the 24v circuit, which normally feeds primarily the backlights, and sometimes the sound. For sure the 24v circuit may not appear to be working, but this is more often than not, because the backlight inverter has failed, and caused the supply to shut down. And whilst we are talking shutdown, it is very rare for faults external to the PSU to cause PSU damage. The switchers fitted to LCD TVs are absolutely *covered* in monitoring circuitry, and any overload condition on any rail, will bring about an immediate shutdown of all secondary supplies, and often, will place the standby supply into a cycling startup mode as well. Most of the failures that I come across involve either the standby supply, or the PFC supply, both of which are primary-side failures. There are many many 'service kits' available to deal with most of these failures, and they are usually quite reasonably priced. They contain all of the components which fail, and if you just go ahead and replace all the parts that they give you, irrespective of whether they appear to be faulty or not, you will usually end up with a working supply. Before totally writing off the existing supplies, you should probably try to diagnose your problems a little deeper, and then see if a kit is available. As to what the demand is on the various rails, they are all quite light except for the 24v rail, where the demand is typically around 4 amps. I use two 12v 50watt halogen lamps in series as a test load for the 24v rail. With regard to trying to use an 'alternative' supply, wired in externally, I personally would not consider doing this as I feel that you may be opening yourself up to all manner of potential safety issues, and certainly would be compromising any safety approvals that were already in place for the equipment. This could bring a whole legal ****storm down on your head, if anyone received any injury as a result ... Far better, I think, that the existing power supplies are repaired. Although diagnosing these supplies is a bit of a black art, contrary to what you believe, most are repairable, and most parts are available, if you look hard enough. Arfa There are a few things I would add. Examining schematics of a few LCD TV power supplies show a great deal of cross coupling in the regulation. Using 5V, 12V, and 24 V supplies and swtiching them on without proper care in the sequencing almost certainly will not work. Parts availablity can be a problem unless you can obtain a parts kit. Parts are not stocked at the local Radio Shack and major suppliers such as Mouser or Digikey may not heve them. PlainBill |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
Parts availablity can be a problem unless you can obtain a parts kit.
Parts are not stocked at the local Radio Shack and major suppliers such as Mouser or Digikey may not heve them. PlainBill Can someone link to a SMPS repair parts kit? I've not seen these. Thanks. |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
"Fester Bestertester" wrote in message ... Parts availablity can be a problem unless you can obtain a parts kit. Parts are not stocked at the local Radio Shack and major suppliers such as Mouser or Digikey may not heve them. PlainBill Can someone link to a SMPS repair parts kit? I've not seen these. Thanks. For instance http://cgi.ebay.co.uk/LCD-PSU-REPAIR...13178002r28571 UK e-bay, but I'm sure a bit of googling or e-bay research would turn up others in the U.S. or wherever Arfa |
#7
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
Far better, I think, that the existing power supplies are repaired. Although diagnosing these supplies is a bit of a black art, contrary to what you believe, most are repairable, and most parts are available, if you look hard enough. Arfa There are a few things I would add. Examining schematics of a few LCD TV power supplies show a great deal of cross coupling in the regulation. Using 5V, 12V, and 24 V supplies and swtiching them on without proper care in the sequencing almost certainly will not work. Parts availablity can be a problem unless you can obtain a parts kit. Parts are not stocked at the local Radio Shack and major suppliers such as Mouser or Digikey may not heve them. PlainBill Interestingly, whole power supplies are available here, sometimes at ridiculously low prices. For instance, many sets use a Vestel chassis, and some of these PSUs are being sold brand new for as little as 25UKP, although you can also find the same PSU at the same vendor for 3 times that, but listed as being for a different make / model, so it's often advantageous to know what power supply is used in multiple different manufacturer's sets. Anyway, the point I was going to make is that a friend of mine whose shop specialises in repair of LCD TV sets, often buys in these power supplies at this price, and fits them into sets that they were never intended to go in, and apparently without any problem. As long as he can find the turn on signal from the system control micro, and there is physically room to fit a Vestel supply in the set in question, he just goes ahead and does it, if necessary, soldering the wires directly to the output connectors. To take your point about cross-coupled regulation, I have not found this to be a problem. I repair a lot of Vestel supplies for the trade, and they are happy to regulate with any load from nothing to full, on any rail, all rails, or no rails at all. As for the rails coming up in any specific order, I think all of the ones that I've seen have all of the switched rails come up together. Certainly, my friend doesn't seem to have ever had an issue with the actual working of an internal supply substitute. Arfa |
#8
Posted to sci.electronics.repair
|
|||
|
|||
Subbing an LCD TV Power Supply
On Tue, 24 Nov 2009 19:42:34 -0000, "Arfa Daily"
wrote: Far better, I think, that the existing power supplies are repaired. Although diagnosing these supplies is a bit of a black art, contrary to what you believe, most are repairable, and most parts are available, if you look hard enough. Arfa There are a few things I would add. Examining schematics of a few LCD TV power supplies show a great deal of cross coupling in the regulation. Using 5V, 12V, and 24 V supplies and swtiching them on without proper care in the sequencing almost certainly will not work. Parts availablity can be a problem unless you can obtain a parts kit. Parts are not stocked at the local Radio Shack and major suppliers such as Mouser or Digikey may not heve them. PlainBill Interestingly, whole power supplies are available here, sometimes at ridiculously low prices. For instance, many sets use a Vestel chassis, and some of these PSUs are being sold brand new for as little as 25UKP, although you can also find the same PSU at the same vendor for 3 times that, but listed as being for a different make / model, so it's often advantageous to know what power supply is used in multiple different manufacturer's sets. Anyway, the point I was going to make is that a friend of mine whose shop specialises in repair of LCD TV sets, often buys in these power supplies at this price, and fits them into sets that they were never intended to go in, and apparently without any problem. As long as he can find the turn on signal from the system control micro, and there is physically room to fit a Vestel supply in the set in question, he just goes ahead and does it, if necessary, soldering the wires directly to the output connectors. To take your point about cross-coupled regulation, I have not found this to be a problem. I repair a lot of Vestel supplies for the trade, and they are happy to regulate with any load from nothing to full, on any rail, all rails, or no rails at all. As for the rails coming up in any specific order, I think all of the ones that I've seen have all of the switched rails come up together. Certainly, my friend doesn't seem to have ever had an issue with the actual working of an internal supply substitute. Arfa I think we were failing to communicate properly here. I interpreted the plan as to buy three separate power supplies (5V, 12V, 24V) and use them to replace an integrated 5V, 12V, 24V supply. I do not think that will work well. You appear to be discussing using a 5V, 12V, 24V supply designed for an XYZ brand of TV in a QED TV. I would have to agree, if dimensional and current ratings are compatible, that should work. From a personal perspective, I 'grew up' with analog power supplies (often using vacuum tube rectifiers). These were inefficient, but easy to repair. The switch to SMPS supplies required more sophisticated techniques, but in the end was not that much more difficult, even for the multiple output supplies found in PCs. At this point I am finding the supplies in LCD TVs to be extremely difficult to troubleshoot safely and effectively. PlainBill |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
QUESTION: How to connect a power supply to my home power grid? | Electronics | |||
HP/Agilent E3632A programmable power supply has power up failure (solution) | Electronics Repair | |||
ATX power supply to bench supply conversion | Electronics Repair | |||
Sanyo DS27214 - Subbing the Power Supply? | Electronics Repair | |||
27" RCA tv chassis:CTC187 subbing HOT | Electronics Repair |