Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
TV turns off when changing channels
I have a Samsung TXE1970. I don't have a remote. Lately, when I try to
change channels by pushing the buttons on the front of the set, the TV turns off; sometimes it will change channels in the wrong direction(eg, go from 6 to 7, instead of 6 to 5). The "turn off" usually happens when trying to go to a higher numbered channel(the button). I haven't done any DMM tests yet, because the board/wires are a tight fit, and it's going to be a hassle to try to duplicate this problem with the board out of the chassis. I am hoping someone can tell me the most likely thing(s) to check: is this more likely just a loose solder joint, some mechanical button/spring issue, or a component prob? Thanks. |
#2
Posted to sci.electronics.repair
|
|||
|
|||
TV turns off when changing channels
It sounds to mike like contaminated circuit board and/or switches... maybe
cracked board traces or bad solder connections. To verify that the problem is only there and not in the system control chip in the television, I would go to WalMart or Radio Shack and get a $cheapo universal remote and verify that the problem only happens with the front panel switches on the television. Best Regards, Daniel Sofie Electronics Supply & Repair - - - - - - - "railbird" wrote in message ups.com... I have a Samsung TXE1970. I don't have a remote. Lately, when I try to change channels by pushing the buttons on the front of the set, the TV turns off; sometimes it will change channels in the wrong direction(eg, go from 6 to 7, instead of 6 to 5). The "turn off" usually happens when trying to go to a higher numbered channel(the button). I haven't done any DMM tests yet, because the board/wires are a tight fit, and it's going to be a hassle to try to duplicate this problem with the board out of the chassis. I am hoping someone can tell me the most likely thing(s) to check: is this more likely just a loose solder joint, some mechanical button/spring issue, or a component prob? Thanks. |
#3
Posted to sci.electronics.repair
|
|||
|
|||
TV turns off when changing channels
Hi!
I have a Samsung TXE1970. I don't have a remote. Lately, when I try to change channels by pushing the buttons on the front of the set, the TV turns off; sometimes it will change channels in the wrong direction(eg, go from 6 to 7, instead of 6 to 5). It really sounds like the control board is being "pressed" in the wrong places. Is the front panel cracked or damaged? In some sets, the buttons are connected together by thin molded plastic. Over time and use, this connection between buttons can or will break. This can cause the buttons to become misaligned or to press on the wrong button inside the set. You could open the set and (carefully!) try operating the buttons directly to see if they work properly. A cheap universal remote (as previously suggested by another poster) would also make a decent test and may be the fastest solution. William |
#4
Posted to sci.electronics.repair
|
|||
|
|||
TV turns off when changing channels
railbird wrote in news:1178721596.868023.23930
@n59g2000hsh.googlegroups.com: . I haven't done any DMM tests yet, because the board/wires are a tight fit, and it's going to be a hassle to try to duplicate this problem with the board out of the chassis. I am hoping someone can tell me the most likely thing(s) to check: is this more likely just a loose solder joint, some mechanical button/spring issue, or a component prob? Thanks. It might not be like my Quasar, but my TV uses a set of resistors with the buttons on the front panel, and that gets pretty wonky. Fortunately, I exclusively run it by remote. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
vinyl channels | Home Repair | |||
French TV channels | UK diy | |||
RCA TV only has a few channels | Electronics Repair | |||
Lost some HD Channels | Electronics Repair | |||
GE 46GW947 keep changing channels | Electronics Repair |