Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to sci.electronics.repair
|
|||
|
|||
JVC RX-318 half dead
Ok I got a weird one.
I ran into a JVC RX-318 that is half dead. when you plug it in, the standby relay comes on, the main speaker relays will also come on 5 seconds after the standby relay comes on, does this under normal conditions also. But the whole front panel is dead, no VFD, no standby LED, nothing. i see filiments, thats about it. I checked the incomming standby 5V, it is present. im at a standstill. any ideas? bad micro? |
#2
Posted to sci.electronics.repair
|
|||
|
|||
JVC RX-318 half dead
here is the funny thing.
If i take and wet my finger a little bit, and touch underneith the crystal, sometimes the front pannel will spring back to life, and shortly after it will "lock up" and go dead again. sometimes it dont work at all. i changed the crystal, didnt resolve it. resoldered the entire area. im at a standstill. any ideas? its like the clockpulse just doesnt want to start. "Mike" wrote in message .. . Ok I got a weird one. I ran into a JVC RX-318 that is half dead. when you plug it in, the standby relay comes on, the main speaker relays will also come on 5 seconds after the standby relay comes on, does this under normal conditions also. But the whole front panel is dead, no VFD, no standby LED, nothing. i see filiments, thats about it. I checked the incomming standby 5V, it is present. im at a standstill. any ideas? bad micro? |
#3
Posted to sci.electronics.repair
|
|||
|
|||
JVC RX-318 half dead
Mike wrote:
here is the funny thing. If i take and wet my finger a little bit, and touch underneith the crystal, sometimes the front pannel will spring back to life, and shortly after it will "lock up" and go dead again. sometimes it dont work at all. i changed the crystal, didnt resolve it. resoldered the entire area. im at a standstill. any ideas? its like the clockpulse just doesnt want to start. "Mike" wrote in message .. . Ok I got a weird one. I ran into a JVC RX-318 that is half dead. when you plug it in, the standby relay comes on, the main speaker relays will also come on 5 seconds after the standby relay comes on, does this under normal conditions also. But the whole front panel is dead, no VFD, no standby LED, nothing. i see filiments, thats about it. I checked the incomming standby 5V, it is present. im at a standstill. any ideas? bad micro? There could be some contamination in the area, a small cap could be leaky, a reset line being pulled down, 5 volt line being just a "bit" low, who knows? Sounds like a fun one all right. A service manual and some experience with problems like this would be good... Mark Z. |
#4
Posted to sci.electronics.repair
|
|||
|
|||
JVC RX-318 half dead
On Sat, 25 Nov 2006 04:54:43 GMT, "Mike" wrote:
Ok I got a weird one. I ran into a JVC RX-318 that is half dead. when you plug it in, the standby relay comes on, the main speaker relays will also come on 5 seconds after the standby relay comes on, does this under normal conditions also. But the whole front panel is dead, no VFD, no standby LED, nothing. i see filiments, thats about it. I checked the incomming standby 5V, it is present. im at a standstill. any ideas? bad micro? I would check for high esr capacitors in the power supply. I had a Nak receiver with the same symptom and it was caused by a faulty electrolytic. Chuck |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Half of breaker panel hot, the other dead!?! | Home Repair | |||
Sony KV32S22 - half-way back from the dead - what now? | Electronics Repair | |||
TV is half dead | Electronics Repair | |||
Old JVC VCRs - half of picture missing | Electronics Repair |