Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to sci.electronics.repair
|
|||
|
|||
Mitsubishi VS-50805 bad convergence.
I went out on a service call for a friend who owns this Mitsubishi
VS-50805. I turned on the set and noticed that there is severe inward bowing on all four sides of the picture. The convergence controls that are accessible to the consumer, do not affect anything. I looked for bad capacitors and poor soldering but it looked in pretty good shape. I put the set back together and told the patient friend of mine that I'd do some research and get back to him. I found the following thread on another repair group forum: message 1 This being a 2000 model set, I don't have any service lit.close to this model.The set has gross mis-converg. I found resistors R8E00 & R8E03 Burned beyond recogin. They appear to be in the +35V line to the convergence IC's IC8D01 &IC8D02. (P/N STK392-040)I'M suspecting the IC's are bad and took out the resistors.If any one has any suggestions on this model or circuit (or possibly any tips from Mitsubishi),please reply? I'm ordering service lit. on it tomorrow but maybe I won't it with a little help.If someone has the values of the resistors I may be able to finish it up? Thank you in advance. Jess @ /message 1 message 2 Both R8E00, And R8E03 Are 120 Ohm/ 1/2 Watt AAnd Are In The +33 Volt Line. /message 2 message 3 (posted by original poster) Changed the 2 burned resistors and shorted IC's. after getting service lit. found i was missing the + & - 24v to the IC's. Changed the 2 circuit protects to get the voltage's back and everything functions normal. /message 3 Can somebody please tell me the part number of the two circuit protectors? Thanks for your reply. -- David Farber David Farber's Service Center L.A., CA |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Mitsubishi VS-50805 bad convergence.
Nothing special, just a 5A pico fuse. Mits # 283P043090
Replace the outputs, STK392-040, the resistors if needed and the fuses and realign. Leonard wrote in message ups.com... I went out on a service call for a friend who owns this Mitsubishi VS-50805. I turned on the set and noticed that there is severe inward bowing on all four sides of the picture. The convergence controls that are accessible to the consumer, do not affect anything. I looked for bad capacitors and poor soldering but it looked in pretty good shape. I put the set back together and told the patient friend of mine that I'd do some research and get back to him. I found the following thread on another repair group forum: message 1 This being a 2000 model set, I don't have any service lit.close to this model.The set has gross mis-converg. I found resistors R8E00 & R8E03 Burned beyond recogin. They appear to be in the +35V line to the convergence IC's IC8D01 &IC8D02. (P/N STK392-040)I'M suspecting the IC's are bad and took out the resistors.If any one has any suggestions on this model or circuit (or possibly any tips from Mitsubishi),please reply? I'm ordering service lit. on it tomorrow but maybe I won't it with a little help.If someone has the values of the resistors I may be able to finish it up? Thank you in advance. Jess @ /message 1 message 2 Both R8E00, And R8E03 Are 120 Ohm/ 1/2 Watt AAnd Are In The +33 Volt Line. /message 2 message 3 (posted by original poster) Changed the 2 burned resistors and shorted IC's. after getting service lit. found i was missing the + & - 24v to the IC's. Changed the 2 circuit protects to get the voltage's back and everything functions normal. /message 3 Can somebody please tell me the part number of the two circuit protectors? Thanks for your reply. -- David Farber David Farber's Service Center L.A., CA -------------------------------------------------------------------------------- I am using the free version of SPAMfighter for private users. It has removed 4436 spam emails to date. Paying users do not have this message in their emails. Try SPAMfighter for free now! |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Mitsubishi VS-50805 bad convergence.
Hi Leonard,
Thanks for the info. I'll put the parts in and report back. -- David Farber David Farber's Service Center L.A., CA "Leonard Caillouet" wrote in message .. . Nothing special, just a 5A pico fuse. Mits # 283P043090 Replace the outputs, STK392-040, the resistors if needed and the fuses and realign. Leonard wrote in message ups.com... I went out on a service call for a friend who owns this Mitsubishi VS-50805. I turned on the set and noticed that there is severe inward bowing on all four sides of the picture. The convergence controls that are accessible to the consumer, do not affect anything. I looked for bad capacitors and poor soldering but it looked in pretty good shape. I put the set back together and told the patient friend of mine that I'd do some research and get back to him. I found the following thread on another repair group forum: message 1 This being a 2000 model set, I don't have any service lit.close to this model.The set has gross mis-converg. I found resistors R8E00 & R8E03 Burned beyond recogin. They appear to be in the +35V line to the convergence IC's IC8D01 &IC8D02. (P/N STK392-040)I'M suspecting the IC's are bad and took out the resistors.If any one has any suggestions on this model or circuit (or possibly any tips from Mitsubishi),please reply? I'm ordering service lit. on it tomorrow but maybe I won't it with a little help.If someone has the values of the resistors I may be able to finish it up? Thank you in advance. Jess @ /message 1 message 2 Both R8E00, And R8E03 Are 120 Ohm/ 1/2 Watt AAnd Are In The +33 Volt Line. /message 2 message 3 (posted by original poster) Changed the 2 burned resistors and shorted IC's. after getting service lit. found i was missing the + & - 24v to the IC's. Changed the 2 circuit protects to get the voltage's back and everything functions normal. /message 3 Can somebody please tell me the part number of the two circuit protectors? Thanks for your reply. -- David Farber David Farber's Service Center L.A., CA -------------------------------------------------------------------------------- I am using the free version of SPAMfighter for private users. It has removed 4436 spam emails to date. Paying users do not have this message in their emails. Try SPAMfighter for free now! |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Mitsubishi Model VS-45603 PTV (No convergence) | Electronics Repair | |||
Mitsubishi VZ5 No convergence | Electronics Repair | |||
Mitsubishi 45" PTV Model # VS-45603 Chassis # VZ5 Convergence Problem | Electronics Repair | |||
MItsubishi VS60609 No convergence correction | Electronics Repair | |||
ICs for Sale - Specials, obsolete and Memory | Electronics Repair |