Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1
Default Kenwood KA-5700 - Please help me repair / Hobby Repair / Blows Fuses

Hello fellow techno-junkies!


I've always been a little of an electronics junkie. I was that kid
who took his toys apart, brought radios and tv's home from the
garbage... Just one of those.

I've been given a Kenwood ka5700 amplifier and have been attempting
to repair it my brother who been given the amp had replaced the fuses
and found they blew almost right after power was applied.

Being so inclined I quickly accepted the gift and put my nose right in
it. I examined the amp deeply and found no obvious signs of damage. I
removed the 4 main power transistors and found 2 had failed.

I replaced them just the other night and with my brother on the phone
the switch was thrown and 1 of replaced transistors managed to smoke
before the fuses blew.... (Note the volume was all the way down and
the speaker select switch was off.)


I have purchase the service manual for the amp and I simply am at a
loss for what to next.

I removed two main jumpers from the amp separating the power supply
from the reset of the amp. According to the service manual power after
the bridge rectifier circuit should be 40v dc. I measure at this point
50v, it's not to spec but is this to high?

What should I do next? I am thinking I should purchase a variac to
introduce a lower ac voltage to the system that may help to determine
the problem. Of course I don't know the trick to repair with this
device. Do I simply apply half the AC power and expect half the
voltage in the circuit from what is listed in the schematic and trace
the components from there.

Do I simply start removing every component and test - then repair and
replace until I've gone through every bit?

It's not so much that I want to repair this particular item, I am
just enjoying the chase.

Thank you for your kind advice. Perhaps someone could recommend a
book?

Tony

  #2   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default Kenwood KA-5700 - Please help me repair / Hobby Repair / Blows Fuses


"Tony Heslington" wrote in message
oups.com...
Hello fellow techno-junkies!


I've always been a little of an electronics junkie. I was that kid
who took his toys apart, brought radios and tv's home from the
garbage... Just one of those.

I've been given a Kenwood ka5700 amplifier and have been attempting
to repair it my brother who been given the amp had replaced the fuses
and found they blew almost right after power was applied.

Being so inclined I quickly accepted the gift and put my nose right in
it. I examined the amp deeply and found no obvious signs of damage. I
removed the 4 main power transistors and found 2 had failed.

I replaced them just the other night and with my brother on the phone
the switch was thrown and 1 of replaced transistors managed to smoke
before the fuses blew.... (Note the volume was all the way down and
the speaker select switch was off.)


I have purchase the service manual for the amp and I simply am at a
loss for what to next.

I removed two main jumpers from the amp separating the power supply
from the reset of the amp. According to the service manual power after
the bridge rectifier circuit should be 40v dc. I measure at this point
50v, it's not to spec but is this to high?

What should I do next? I am thinking I should purchase a variac to
introduce a lower ac voltage to the system that may help to determine
the problem. Of course I don't know the trick to repair with this
device. Do I simply apply half the AC power and expect half the
voltage in the circuit from what is listed in the schematic and trace
the components from there.

Do I simply start removing every component and test - then repair and
replace until I've gone through every bit?

It's not so much that I want to repair this particular item, I am
just enjoying the chase.

Thank you for your kind advice. Perhaps someone could recommend a
book?

Tony


The variac trick only works if the amp is not electronically switched. If it
is, you need to get to at least 75% of the line input voltage before the
drive to the power switching relay will come up. By this time, the rails
will be up high enough to blow your transistors again. The way around this
is to bridge the power relay, but you need to understand the schematics and
what you are doing, to do this correctly and safely. The variac is
definitely the right approach for this type of fault on this type of
equipment, assuming that you possess one. You are correct in your surmisal
that half the input voltage equals half the secondary rails, but half is way
too much. If you understand what you are measuring as you bring the input
voltage up, 10 - 20% is plenty enough to find the fault.

In going for a repair on a DC coupled amp, which has a failed output stage,
you have picked a notoriously difficult area. Some of these amps can have
even the most experienced of us, who work on them all the time, tearing our
hair out.

Before investing in a variac, assuming that the other channel works ok -
prove this by removing the bad o/p Tr's, fitting new fuses, and retrying -
you might try just doing comparison checks of resistance between the good
channel and the bad. I would suggest an analogue multimeter for this, as it
tends to give a quicker and more meaningful display than a digital. Set the
meter to a standard ohms x 1 range, clip the black lead to deck, then do
comparison checks between corresponding points on the two channels. As soon
as you find a significant difference, chase this down to arrive at the
faulty component(s).

I'm willing to bet that as well as your bad output transistors, you also
have at least one bad driver transistor. Also check for open circuit
resistors. Typical places for these after an output stage failure, are the
low value high power emitter resistors for the output pair, and base
coupling resistors, which are often tiny low value types.

I wish you luck with it but, based on many years' experience, I fear that
you may not get very far.

Arfa


  #3   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2
Default Kenwood KA-5700 - Please help me repair / Hobby Repair / Blows Fuses

Tony , look in the circuit corresponding to the output that blew again and
there are driver transistors in that circuit that drive the bigger power
transistors ... check them for shorted or open or for a bad gate ... its a
typical output stage and when you lose the main outputs it usually takes out
the pre-drivers with it , not always but sometimes ... i would almost bet
you that one of your pre-drivers is shorted ..... always compare one channel
to the other with a meter at different points , i usually meter all drivers
transistors as its a good sign when all the drivers are reading good , then
i proceed to the final output stage then i will meter and compare the final
stages against each other before i fire it back up ..... hope this helps


regards


"Tony Heslington" wrote in message
oups.com...
Hello fellow techno-junkies!


I've always been a little of an electronics junkie. I was that kid
who took his toys apart, brought radios and tv's home from the
garbage... Just one of those.

I've been given a Kenwood ka5700 amplifier and have been attempting
to repair it my brother who been given the amp had replaced the fuses
and found they blew almost right after power was applied.

Being so inclined I quickly accepted the gift and put my nose right in
it. I examined the amp deeply and found no obvious signs of damage. I
removed the 4 main power transistors and found 2 had failed.

I replaced them just the other night and with my brother on the phone
the switch was thrown and 1 of replaced transistors managed to smoke
before the fuses blew.... (Note the volume was all the way down and
the speaker select switch was off.)


I have purchase the service manual for the amp and I simply am at a
loss for what to next.

I removed two main jumpers from the amp separating the power supply
from the reset of the amp. According to the service manual power after
the bridge rectifier circuit should be 40v dc. I measure at this point
50v, it's not to spec but is this to high?

What should I do next? I am thinking I should purchase a variac to
introduce a lower ac voltage to the system that may help to determine
the problem. Of course I don't know the trick to repair with this
device. Do I simply apply half the AC power and expect half the
voltage in the circuit from what is listed in the schematic and trace
the components from there.

Do I simply start removing every component and test - then repair and
replace until I've gone through every bit?

It's not so much that I want to repair this particular item, I am
just enjoying the chase.

Thank you for your kind advice. Perhaps someone could recommend a
book?

Tony



  #4   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 175
Default Kenwood KA-5700 - Please help me repair / Hobby Repair / BlowsFuses



bloggybob wrote:
Tony , look in the circuit corresponding to the output that blew again and
there are driver transistors in that circuit that drive the bigger power
transistors ... check them for shorted or open or for a bad gate ... its a
typical output stage and when you lose the main outputs it usually takes out
the pre-drivers with it , not always but sometimes ... i would almost bet
you that one of your pre-drivers is shorted ..... always compare one channel
to the other with a meter at different points , i usually meter all drivers
transistors as its a good sign when all the drivers are reading good , then
i proceed to the final output stage then i will meter and compare the final
stages against each other before i fire it back up ..... hope this helps


regards


If that's the antique i think it is, good luck getting the output
transistors. They were something like B688's or such with mount tabs
on the sides. If your clever, you can retrofit others in but its hardly
worth the hassle.

Bob

----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
  #5   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 533
Default Kenwood KA-5700 - Please help me repair / Hobby Repair / BlowsFuses

Bob Urz wrote:


bloggybob wrote:
Tony , look in the circuit corresponding to the output that blew again
and
there are driver transistors in that circuit that drive the bigger power
transistors ... check them for shorted or open or for a bad gate ...
its a
typical output stage and when you lose the main outputs it usually
takes out
the pre-drivers with it , not always but sometimes ... i would almost bet
you that one of your pre-drivers is shorted ..... always compare one
channel
to the other with a meter at different points , i usually meter all
drivers
transistors as its a good sign when all the drivers are reading good ,
then
i proceed to the final output stage then i will meter and compare the
final
stages against each other before i fire it back up ..... hope this helps


regards


If that's the antique i think it is, good luck getting the output
transistors. They were something like B688's or such with mount tabs
on the sides. If your clever, you can retrofit others in but its hardly
worth the hassle.

Bob


It is an antique; but I believe he said he'd replaced the out's once
already....

jak


----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet
News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----




  #6   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 100
Default Kenwood KA-5700 - Please help me repair / Hobby Repair / Blows Fuses

On 8 Jul 2006 14:13:54 -0700, "Tony Heslington"
wrote:

Hello fellow techno-junkies!


I've always been a little of an electronics junkie. I was that kid
who took his toys apart, brought radios and tv's home from the
garbage... Just one of those.

I've been given a Kenwood ka5700 amplifier and have been attempting
to repair it my brother who been given the amp had replaced the fuses
and found they blew almost right after power was applied.

Being so inclined I quickly accepted the gift and put my nose right in
it. I examined the amp deeply and found no obvious signs of damage. I
removed the 4 main power transistors and found 2 had failed.

I replaced them just the other night and with my brother on the phone
the switch was thrown and 1 of replaced transistors managed to smoke
before the fuses blew.... (Note the volume was all the way down and
the speaker select switch was off.)


I have purchase the service manual for the amp and I simply am at a
loss for what to next.

I removed two main jumpers from the amp separating the power supply
from the reset of the amp. According to the service manual power after
the bridge rectifier circuit should be 40v dc. I measure at this point
50v, it's not to spec but is this to high?

What should I do next? I am thinking I should purchase a variac to
introduce a lower ac voltage to the system that may help to determine
the problem. Of course I don't know the trick to repair with this
device. Do I simply apply half the AC power and expect half the
voltage in the circuit from what is listed in the schematic and trace
the components from there.

Do I simply start removing every component and test - then repair and
replace until I've gone through every bit?

It's not so much that I want to repair this particular item, I am
just enjoying the chase.

Thank you for your kind advice. Perhaps someone could recommend a
book?

Tony




As someone who repaired a large volume of these amps, I would suggest
putting a 60 watt bulb in series with the hot side of the AC input.
Then if I was inexperienced in repairing amps, I would replace the
driver, output, and bias transistors and check the values of resistors
in the related circuitry. Sometimes on this amp, the differential
input transistors would fail causing a dc offset on the output. After
replacing these parts, turn the amplifier on and see ,after the
initial brightness of the bulb, if the bulb dims and if the amplifier
works. If it doesn't you will at least know there are other problems
and most likely won't damage any components. Once the amp is
functional, plug it directly into the wall and set the bias and offset
voltages. This amp isn't too shabby and is much easier to work on
than the multichannel wonders on the market today. Chuck
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Motor repair - Kenwood mixer Iain Mac Donald UK diy 14 November 3rd 05 07:17 PM
Refrigerator repair story with a happy ending ! wgd Home Repair 16 July 4th 05 08:40 PM
LeCroy Oscilloscope/ VME/ CAMAC/ NIM/ FASTBUS repair fernando1222 Electronics Repair 0 June 7th 05 10:18 PM
Kenwood Car stereo repair HELP!! Barry & Nikki Electronics Repair 4 November 16th 04 06:03 AM
RCA 36" TV blows fuses David G. Electronics Repair 2 February 16th 04 01:44 AM


All times are GMT +1. The time now is 02:18 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"