Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Zenith model # A3241w
working on this set replace cx3231, HOT str53041, the set only click once
and no hv need help on this set it's beating . do'nt have a sam on this set it have a 9-2003 board in it . i've repaired chassis almost like this one but this one is a pistol any help will be greatful a appreciated. i thought it was the fly but it not blowing any fuse or the HOT. |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Zenith model # A3241w
Jonesy82 wrote:
working on this set replace cx3231, HOT str53041, the set only click once and no hv need help on this set it's beating . do'nt have a sam on this set it have a 9-2003 board in it . i've repaired chassis almost like this one but this one is a pistol any help will be greatful a appreciated. i thought it was the fly but it not blowing any fuse or the HOT. if the HOT was out and you replaced it with a new one then you have 2 possible problems. you have a shorted flyback which is most likely or one of the low voltage taps have shorted diodes/caps! but in that case, you normally get a short attempt to start and shut down. -- Real Programmers Do things like this. http://webpages.charter.net/jamie_5 |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Zenith model # A3241w
"Jonesy82" wrote in message news:sOIVf.3195$fS6.2973@dukeread11... working on this set replace cx3231, HOT str53041, the set only click once and no hv need help on this set it's beating . do'nt have a sam on this set it have a 9-2003 board in it . i've repaired chassis almost like this one but this one is a pistol any help will be greatful a appreciated. i thought it was the fly but it not blowing any fuse or the HOT. did you try powering the set up without the HOT in place- if so did the psu come up ok with hv and low voltage supplied reading ok? |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Zenith model # A3241w
Jonesy82 wrote: working on this set replace cx3231, HOT str53041, the set only click once and no hv need help on this set it's beating . do'nt have a sam on this set it have a 9-2003 board in it . . . . If you haven't already, replace CX3416 (100 uf). The power supply won't run if it's bad. Here's a nice low tech diagnostic for the SMPS: When you plug the set in you should hear a soft, sweet little squeak from the SMPS. If the set is in shutdown, you will hear this sweet little squeak when you UNPLUG the set. Occassionally D3410 will be shorted. It will shut down the PS, but will NOT blow the line fuse. If D3410 is shorted you will hear the powerdown squeak mentioned previously. David, on the Illinois prairie. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
(Zenith), Wards, 1989 console model 17750, SVC # PL2511H152 will not power up. | Electronics Repair | |||
Zenith H1913Y 1990 model TV - no audio | Electronics Repair | |||
Zenith TV model B25A24Z no sound | Electronics Repair | |||
Zenith Color tv Model # H2017Y7 Color problem | Electronics Repair | |||
Won't buy another new Zenith | Electronics Repair |