Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Removing a Fluorescent Display
My stereo receiver (a Sony STR-AV780) has a vacuum fluorescent display (VFD)
which goes dim intermittently. I have replaced some electrolytic capacitors already which has helped but there is another one I'd like change. Unfortunately it is mounted UNDER the VFD. The display tube is about 7 by 2 inches and mounted in a dual-inline socket. The socket is not a zero-insertion-force model. How do I remove and replace the glass display tube without damaging it? Chuck |
#2
|
|||
|
|||
I have worked on many Sony receivers with Fluorescent displays..... I
am guessing that what you are thinking is a socket is really a spacer and the display is soldered directly to the pcb. .... simple enough, get your solder wick out and un-solder and remove the display. electricitym |
#3
|
|||
|
|||
wrote in message
oups.com... I have worked on many Sony receivers with Fluorescent displays..... I am guessing that what you are thinking is a socket is really a spacer and the display is soldered directly to the pcb. .... Oooooh, I'll bet you're right. simple enough, get your solder wick out and un-solder and remove the display. I had considered doing that. It wouldn't take me too long and there's a much lower probability of damaging the display even if that spacer was a socket. Thanks for the reply. -- Chuck |
#4
|
|||
|
|||
"Charles" wrote in message ... wrote in message oups.com... I have worked on many Sony receivers with Fluorescent displays..... I am guessing that what you are thinking is a socket is really a spacer and the display is soldered directly to the pcb. .... Oooooh, I'll bet you're right. simple enough, get your solder wick out and un-solder and remove the display. I had considered doing that. It wouldn't take me too long and there's a much lower probability of damaging the display even if that spacer was a socket. Yeah give that a shot, those Radio Shack desoldering irons work pretty well for that sort of thing, one of the few worthwhile things they sell. Also if it has pins on both sides you may find that desoldering one side is sufficient to flip the display up and get to that cap. |
#5
|
|||
|
|||
"James Sweet" wrote in message
news:sIGAe.4086$Gk4.3588@trnddc01... Yeah give that a shot, those Radio Shack desoldering irons work pretty well for that sort of thing, one of the few worthwhile things they sell. I've got my trusty Edsyn Silverstat Soldapullt at hand. It works well if I keep it clean and greased. (About twenty years ago the nice people at Clearco Products sent me a 2 ounce sample of their silicone grease. I love that stuff.) Also if it has pins on both sides you may find that desoldering one side is sufficient to flip the display up and get to that cap. Those pins look pretty stout and I think I need to heat up the pins anyway. I took the cover off the receiver this morning to monitor some voltages. As luck would have it, the display, which was dim when the cover was on, is fine now. This is beginning to smell like a cold solder joint. I had the same problem with a Sony TV a while back. Heavy components vibrate slightly while going over the solder bath on the conveyor. They keep vibrating while the solder cools. As I resoldered the connections to the flyback transformer of that TV receiver, one of the joints gave an audible crack as I relieved the tension on it. After that it quit eating the horizontal drive transistor. Maybe the fluorescent display has the same problem. -- Chuck |
#6
|
|||
|
|||
I spent about two hours this afternoon removing the fluorescent display and
replacing the electrolytic capacitor hidden underneath. electricitym was right. The display (a Futaba 1-519-392-11) was not socketed. It is soldered directly to the printed circuit board and held off the board by a plastic spacer. There are about 80 connections to unsolder which didn't take long. The only hangup was releasing the spacer from the board. One of the three tabs which secures the spacer to the board was tight. I inspected and straightened all the pins on the display before reinserting it so lining the pins up to reinsert the display went well. The display which was exhibiting some uneven illumination yesterday looks good. -- Chuck |
#7
|
|||
|
|||
yup, I was going to say 'if in doubt just unsolder
the socket' "Charles" wrote in message ... : wrote in message : oups.com... : I have worked on many Sony receivers with Fluorescent displays..... I : am guessing that what you are thinking is a socket is really a spacer : and the display is soldered directly to the pcb. .... : : Oooooh, I'll bet you're right. : : simple enough, get your solder wick out and un-solder and remove the display. : : I had considered doing that. It wouldn't take me too long and there's a much : lower probability of damaging the display even if that spacer was a socket. : : Thanks for the reply. : : -- : Chuck : : |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Flakey LCD display on PowerBook | Electronics Repair | |||
Display dead, Panasonic NV-HD100 | Electronics Repair | |||
Display has no hard wire connections. | Electronics Repair | |||
Siemens Gigaset 2420 Display problem | Electronics Repair | |||
FA: Sharp 320 x 240 backlight monochrome touch screen LCD display LM32015T | Electronics Repair |